Performance Tool W1612 2.5 Ton Hydraulic Floor Jack User Manual

1. Коопсуздук маалыматы

Always prioritize safety when operating the Performance Tool W1612 hydraulic floor jack. Failure to follow these instructions may result in serious injury or property damage.

• Колдонмону окуу: Read and understand all instructions and warnings in this manual before using this product.
• Тегиз, катуу бетте колдонуу: Operate the jack only on a hard, level surface capable of supporting the load. Avoid uneven or soft ground.
• Кубаттуулуктан ашпаңыз: Never exceed the rated capacity of 5,000 lbs (2.5 tons).
• Джек стенддерин колдонуңуз: After lifting the vehicle to the desired height, always support it immediately with appropriately rated jack stands. The hydraulic jack is a lifting device only and is not designed to sustain loads for extended periods.
• Жүктү борборлоштуруу: Ensure the load is centered on the jack saddle. Off-center loads can cause instability.
• Коопсуздук шаймандарын кийүү: Always wear ANSI-approved safety goggles and heavy-duty work gloves during operation.
• Таза кармоо: Keep hands, feet, and other body parts clear of moving parts and the vehicle during lifting and lowering.
• Колдонуудан мурун текшерүү: Before each use, inspect the jack for any damage, leaks, or loose parts. Do not use if damaged.
• Туура сактоо: Store the jack in a clean, dry place, fully lowered, when not in use.

2. Продукт бүтүп калдыview

The Performance Tool W1612 is a heavy-duty 2.5 ton (5,000 lb) hydraulic floor jack designed for lifting vehicles. It features a robust steel construction, wide front wheels, and a 360-degree swivel saddle for ease of use.

Негизги компоненттер:

• Кол көтөрүү: The main arm that raises and lowers the vehicle.
• Ээр: The contact point with the vehicle's lifting area.
• туткасы: Used for pumping to lift and rotating to lower.
• Чыгаруучу клапан: Домкраттын түшүрүү ылдамдыгын башкарат.
• Wheels/Casters: Allow for easy positioning and maneuvering.

Figure 1: Performance Tool W1612 2.5 Ton Hydraulic Floor Jack. This image shows the overall design of the yellow hydraulic floor jack with its long handle and wheels.

2-сүрөт: Каптал view of the Performance Tool W1612 Hydraulic Floor Jack. This image provides a different angle of the jack, highlighting its low-profile design and robust construction.

3. Орнотуу

Алгачкы даярдоо:

1. Пакеттен чыгаруу: Carefully remove the jack from its packaging. Inspect for any shipping damage.
2. Туткасы Ассамблеясы: Insert the handle into the handle socket and secure it according to the instructions provided in the packaging.

Bleeding the Hydraulic System:

Air can become trapped in the hydraulic system during shipping or use, affecting performance. Bleeding the system removes this air.

1. Open Release Valve: Turn the handle counter-clockwise to fully open the release valve.
2. Насос туткасы: Pump the handle 6-8 full strokes to force air out of the system.
3. Close Release Valve: Чыгаруучу клапанды жабуу үчүн тутканы саат жебеси боюнча буруңуз.
4. Сыноо: Test the jack by lifting and lowering it a few times without a load. If the jack does not lift smoothly or to its full height, repeat the bleeding process.

4. Иштөө нускамалары

Lifting a Vehicle:

1. Унаа даярдоо: Park the vehicle on a hard, level surface. Engage the parking brake and block the wheels that will remain on the ground.
2. Жектин кызматы: Position the jack directly under the vehicle's designated lifting point. Consult your vehicle's owner's manual for proper lifting points.
3. Close Release Valve: Turn the handle clockwise until the release valve is firmly closed. Do not overtighten.
4. Көтөрүп жүрүүчү унаа: Pump the handle up and down to raise the vehicle to the desired height. Ensure the vehicle remains stable during lifting.
5. Жек Стенддери менен бекемдеңиз: Once the vehicle is at the desired height, immediately place appropriately rated jack stands under the vehicle's frame or designated support points.
6. Slightly Lower onto Stands: Slowly turn the handle counter-clockwise to open the release valve, allowing the vehicle to gently rest onto the jack stands. Remove the hydraulic jack once the vehicle is securely supported by the stands.

Lowering a Vehicle:

1. Reposition Jack: If removed, place the hydraulic jack back under the vehicle's lifting point and raise it slightly to take the load off the jack stands.
2. Джек стенддерин алып салыңыз: Домкрат таянычтарын унаанын астынан этияттык менен алып салыңыз.
3. Төмөнкү унаа: Slowly turn the handle counter-clockwise to open the release valve. Control the lowering speed by adjusting how much you open the valve.
4. Fully Lower: Унаа толугу менен түшүрүлгөндөн кийин, домкратты алып салыңыз.

5. Техникалык тейлөө

Regular maintenance ensures the longevity and safe operation of your hydraulic floor jack.

• Гидравликалык суюктуктун деңгээли: Check the hydraulic fluid level periodically. With the jack fully lowered, remove the oil filler plug. The fluid level should be just below the filler hole. Top up with high-quality hydraulic jack oil if necessary. Do not use brake fluid or motor oil.
• Майлоо: Lubricate all moving parts and pivot points with light machine oil monthly or as needed.
• Тазалоо: Keep the jack clean and free of dirt, grease, and corrosive materials. Wipe down the ram and pump plungers after each use.
• Сактагыч: Store the jack in a dry, protected area, fully lowered, to prevent rust and seal damage.

6. Кыйынчылыктарды

7. Техникалык шарттар

• Модел: W1612
• Жүктөө жөндөмдүүлүгү: 5,000 lbs (2.5 Tons)
• Максималдуу көтөрүү бийиктиги: 19.25 дюйм
• Minimum Lifting Height: Approximately 5 inches (standard floor jack minimums)
• Материал: Эритме болот
• Элемент Салмагы: 79.7 фунт
• Продукциянын өлчөмдөрү (L x W x Y): 30.6 x 8.6 x 15.4 дюйм
• Унаа тейлөө түрү: Автоунаа, жүк ташуучу унаа

8. Кепилдик жана колдоо

For warranty information or technical support regarding your Performance Tool W1612 hydraulic floor jack, please refer to the documentation included with your purchase or contact Performance Tool customer service directly. Keep your purchase receipt for warranty claims.

Өндүрүүчү: Performance Tool (Wilmar Corporation)

UPC: 039564124778

Биринчи жеткиликтүү болгон күнү: 1-апрель, 2004-жыл