Introduction
This manual provides essential instructions for the proper setup, operation, and maintenance of your Intermec SR30 Linear Imager RS232 Barcode Scanner. Please read this manual thoroughly before using the device to ensure optimal performance and to prevent damage.
The Intermec SR30 is a high-performance linear imager designed for reliable barcode scanning in various environments, connecting via an RS232 interface.
Коопсуздук маалыматы
- Сканерди экстремалдык температурага, нымдуулукка же тике күн нуруна калтырбаңыз.
- Сканерди түшүрүп алуудан же катуу соккуга кабылтуудан алыс болуңуз.
- Do not attempt to open or modify the scanner. Refer all servicing to qualified personnel.
- Use only the power supply and cables provided or approved by Intermec.
- Штрих-коддун так окулушун камсыз кылуу үчүн сканерлөө терезесин таза кармаңыз.
Пакеттин мазмуну
Пакетиңизде төмөнкү заттар бар экенин текшериңиз:
- Intermec SR30 Linear Imager Barcode Scanner
- RS232 Interface Cable
- Электр менен жабдуу бирдиги
- Документтер (бул колдонмо же ушул сыяктуу)
Эгерде кандайдыр бир буюмдар жок болсо же бузулуп калса, дароо жеткирүүчүңүзгө кайрылыңыз.
Жайгашуу
1. Сканерди туташтыруу
- Connect the RS232 Cable: Plug the RS232 connector of the interface cable into the corresponding serial port on your host computer or POS system.
- Сканерге туташуу: Plug the other end of the interface cable into the port at the base of the SR30 scanner. Ensure a secure connection.
- Кубат булагына туташтыруу: Connect the power supply unit to the power port on the interface cable or directly to the scanner base, as applicable for your specific cable configuration. Plug the power supply into a standard electrical outlet.
2. Баштапкы күйгүзүү
Once connected, the scanner should power on automatically. Observe the indicator lights (typically an LED) for initial status. The scanner may emit a short beep to indicate it is ready for operation.
3. Basic Configuration (if required)
The SR30 scanner may require configuration for specific RS232 communication parameters (e.g., baud rate, data bits, parity) to match your host system. Refer to the detailed programming guide (often a separate document with programming barcodes) for advanced configuration. For basic operation, the default settings are often sufficient.
Сканерди иштетүү
1. Штрихкоддорду сканерлөө
- Максаты: Point the scanning window of the SR30 at the barcode you wish to read. Ensure the entire barcode is within the scanner's field of view.
- Скандоо: Press and hold the trigger button (if applicable) or present the barcode to the scanner's window for automatic scanning.
- Ырастоо: A successful scan is typically indicated by an audible beep and/or a change in the LED indicator light (e.g., green light). The barcode data will be transmitted to your host system.
2. Understanding Indicators
- Жашыл LED: Indicates a successful barcode read.
- Red/Amber LED: May indicate an error, scanner busy, or awaiting input. Consult the full programming guide for specific error codes or patterns.
- Beep Sounds: Different beep patterns can indicate successful reads, errors, or configuration changes.
Техникалык тейлөө
Сканерди тазалоо
- Сканерлөө терезесин жумшак, мамыксыз чүпүрөк менен үзгүлтүксүз тазалап туруңуз dampсуу же жумшак, абразивдик тазалоочу каражат менен тазалаңыз.
- Do not use harsh chemicals, solvents, or abrasive materials, as these can damage the scanner's surface.
- Тазалоодон мурун сканердин өчүрүлгөнүн текшериңиз.
Сактагыч
Колдонулбай турган учурда, сканерди таза, кургак жерде, күндүн түз нурунан жана өтө жогорку температурадан алыс сактаңыз.
Проблемаларды чечүү
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Сканер күйбөйт. | Power cable not connected; power outlet faulty; power supply unit failure. | Check all cable connections. Try a different power outlet. Ensure the power supply is functioning. |
| Сканер штрих-коддорду окубайт. | Barcode damaged or poorly printed; scanning window dirty; incorrect symbology enabled; scanner not configured for host. | Ensure barcode is clear. Clean scanning window. Verify scanner configuration matches host system requirements. Try scanning a known good barcode. |
| Barcode data not appearing on host. | RS232 cable loose or faulty; incorrect RS232 communication settings (baud rate, parity); host application not ready. | Check RS232 cable connection. Verify RS232 settings on both scanner and host. Ensure host application is active and ready to receive input. |
Техникалык шарттар
- Модел: SR30
- Бөлүмдүн номери: 225-727-003 (Kit)
- Сканер түрү: Lineer Imager
- Интерфейс: RS232
- Өндүрүүчү: Intermec
- Элемент Салмагы: 0.01 ounces (approximate, scanner only)
- Бөлүм: Штрихкод
- ASIN: B003T0WF3S
Кепилдик жана колдоо
For warranty information and technical support, please refer to the documentation provided with your purchase or visit the official Intermec webсайт. Сатып алуу квитанциясын кепилдик дооматтары үчүн сатып алуунун далили катары сактаңыз.
Contact your reseller or Intermec customer service for assistance with issues not covered in this manual.