LASCO 06-9123 Angle Stop Adapter Tee User Manual

Introduction

This manual provides instructions for the proper installation, operation, and maintenance of the LASCO 06-9123 Angle Stop Adapter Tee. This lead-free brass fitting is designed to add an additional water line to an existing single outlet supply valve. Please read these instructions carefully before installation to ensure safe and correct usage.

Коопсуздук маалыматы

• Сантехникалык иштерди баштоодон мурун ар дайым негизги суу менен камсыздоону өчүрүп коюңуз.
• Коргоочу көз айнектер жана кол каптар сыяктуу тиешелүү жеке коргоочу шаймандарды кийиңиз.
• Ensure all connections are tight to prevent leaks. Do not overtighten, as this can damage threads or components.
• This product is made from lead-free rough brass and is approved for use in all states.
• Эгер кандайдыр бир кадамга ишенбесеңиз, квалификациялуу сантехникке кайрылыңыз.

Пакеттин мазмуну

• 1 x LASCO 06-9123 Angle Stop Adapter Tee

Техникалык шарттар

Орнотуу нускамалары

Follow these steps to install the LASCO 06-9123 Angle Stop Adapter Tee:

1. аймакты даярдоо:

   Locate the existing single outlet supply valve. Ensure there is sufficient space for the adapter tee and the additional water line.

   

   Image: The LASCO 06-9123 Angle Stop Adapter Tee, showing its three connection points. This image illustrates the overall design of the product.
2. Суу менен камсыздоону өчүрүү:

   Turn off the main water supply to the area where you will be working. Open a nearby faucet to relieve any pressure in the lines.

3. Disconnect Existing Line:

   Carefully disconnect the existing water supply line from the single outlet supply valve. Have a towel ready to catch any residual water.

4. Install Adapter Tee:

   Connect one of the 3/8-inch OD compression ends of the adapter tee to the existing supply valve. Hand-tighten first, then use a wrench to secure, being careful not to overtighten.

   Эскертүү: The adapter tee features two 3/8-inch OD compression connections and one 1/2-inch slip joint connection. The compression connections are typically used for flexible supply lines, while the slip joint is often used for rigid pipes or specific appliance connections.

5. Reconnect Existing Line:

   Connect the previously disconnected water supply line to the other 3/8-inch OD compression end of the adapter tee. Secure tightly.

6. Connect New Water Line:

   Connect your new water line (e.g., for a bidet, humidifier, or other appliance) to the 1/2-inch slip joint connection of the adapter tee. Ensure a proper seal, using thread sealant or tape if required for the specific connection type.

   

   Сүрөт: жакын план view of the adapter tee, highlighting the different connection types (3/8-inch compression and 1/2-inch slip joint) for clarity during installation.

7. Агышууларды текшерүү:

   Slowly turn the main water supply back on. Carefully inspect all connections for any signs of leaks. Tighten any leaking connections slightly until the leak stops. Do not overtighten.

Операция

Once installed, the LASCO 06-9123 Angle Stop Adapter Tee functions as a passive splitter, allowing water to flow to both connected lines simultaneously from a single supply valve. There are no moving parts or controls on the adapter tee itself.

Техникалык тейлөө

The LASCO 06-9123 Angle Stop Adapter Tee requires minimal maintenance. Periodically inspect the connections for any signs of corrosion or leaks. If a leak is detected, ensure the connection is secure. If the leak persists, the fitting may need to be re-sealed or replaced.

Проблемаларды чечүү

• Туташуулардагы агып кетүүлөр:

  Ensure all compression nuts are tightened properly. For slip joint connections, verify that the washer is correctly seated and the nut is snug. Avoid overtightening, which can damage the fitting or tubing. If using thread tape or sealant, ensure it was applied correctly.
• Суунун жетишсиз агымы:

  Check that the main water supply valve is fully open. Inspect connected lines for kinks or obstructions. The adapter tee itself does not restrict flow significantly.

Кепилдик маалымат

This LASCO product comes with a 1 жылдык Чектелген Кепилдик from the date of purchase. This warranty covers defects in material and workmanship under normal use and service. For warranty claims or further details, please contact LASCO customer support.

Кардарларды колдоо

For technical assistance, replacement parts, or general inquiries, please visit the official LASCO website or contact their customer service department. Refer to your product packaging or the LASCO webакыркы байланыш маалыматы үчүн сайт.

LASCO Official Webсайт: www.lascofittings.com