KeylessOption 3-Button Key Fob Remote Control Replacement

Introduction

This manual provides comprehensive instructions for the installation, programming, and maintenance of your KeylessOption 3-Button Key Fob Remote Control Replacement. This product is designed to replace your original factory remote with a reliable and functional alternative. Please read all instructions carefully before proceeding.

Пакеттин мазмуну

Пакетиңизде бардык буюмдар бар экенин текшериңиз:

• KeylessOption 3-Button Remote Control(s)
• CR2032 Lithium Battery(s) (pre-installed)
• Ачкыч шакекчелеринин илмектери
• Programming Instructions (included with product)

Figure 1: Contents of the KeylessOption Key Fob package. Includes remote controls, pre-installed batteries, and key ring loops.

Унаа шайкештиги

This key fob is compatible with specific vehicle models and years. Ensure your vehicle is listed below before attempting to program the remote. This remote is a replacement for OEM part numbers LHJ011, 15186200, 15186201, 15132197, 15132198, 10377295, 22730827, 15186203, & 21997127 (FCC ID: LHJ011).

• Кадиллак: Escalade (2003-2007)
• Chevrolet: Avalanche (2003-2007), Silverado (2003-2007), Suburban (2003-2007), Tahoe (2003-2007)
• GMC: Sierra (2003-2007), Yukon (2003-2007)
• Hummer: H2 (2003-2007)

Figure 2: Visual guide to self-programming and compatible vehicle models.

Key Fob Features

Your KeylessOption remote features three distinct buttons for convenient vehicle control:

• Кулпу баскычы: Secures all vehicle doors.
• Кулпуну ачуу баскычы: Бардык унаа эшиктерин ачат.
• Паника баскычы: Activates the vehicle's alarm system for emergency situations.

Сүрөт 3: Алдыңкы view of the key fob, highlighting the Lock, Unlock, and Panic buttons.

Программалоо нускамалары

This key fob is designed for self-programming. The exact steps may vary slightly by vehicle model and year. Always refer to your vehicle's owner's manual for the most accurate programming procedure. A common procedure for compatible GM vehicles is as follows:

1. Ensure all vehicle doors are closed.
2. Айдоочунун отургучуна отуруңуз.
3. Insert your vehicle's ignition key into the ignition.
4. басып туруңуз БҮЛПӨНҮ АЧУУ айдоочу тараптагы эшиктин панелиндеги баскыч.
5. кармап жатканда БҮЛПӨНҮ АЧУУ button, cycle the ignition key from ӨЧҮРҮҮ чейин ON жана кайра ӨЧҮРҮҮ two times. Do not start the engine.
6. бошотуңуз БҮЛПӨНҮ АЧУУ button. The vehicle's door locks should cycle (lock and unlock) to indicate that the vehicle is now in programming mode.
7. On the new key fob, simultaneously press and hold the БУЛПОО жана БҮЛПӨНҮ АЧУУ buttons for approximately 15 seconds. The vehicle's door locks should cycle again to confirm successful programming of the first remote.
8. If programming additional remotes (including existing ones), immediately repeat step 7 for each additional remote. All remotes must be programmed during the same session.
9. To exit programming mode, turn the ignition key to the ON position, then remove the key. The door locks should cycle one last time.
10. Test all programmed remotes to ensure full functionality.

Important Note for Multiple Fobs: If you are programming more than one key fob, ensure you program all of them during the same session. If you program one and then exit programming mode before programming the others, the previously programmed fobs may become unprogrammed.

Батареяны алмаштыруу

The key fob uses a CR2032 lithium battery. If the remote's range decreases or it stops responding, the battery may need replacement.

1. Locate the small notch on the side of the key fob.
2. Using a small flat-head screwdriver or a coin, carefully pry open the two halves of the key fob at the notch.
3. Remove the old CR2032 battery. Note the orientation (+/-) of the battery.
4. Жаңы CR2032 батареясын оң (+) тарабын өйдө каратып салыңыз.
5. Carefully snap the two halves of the key fob back together until they are securely closed.
6. Ачкычтын функциясын текшериңиз.

Figure 4: Back of the key fob, indicating the opening point for battery replacement.

Техникалык шарттар

Проблемаларды чечүү

• Fob not responding after programming:
  • Ensure all steps of the programming procedure were followed precisely.
  • If programming multiple fobs, ensure all were programmed in the same session. Reprogram all fobs if necessary.
  • Check the battery. Replace if necessary, ensuring correct polarity.
  • Унаанын шайкештигин текшерүү.
• Кыскартылган диапазон:
  • Батарея аз болушу мүмкүн. CR2032 батареясын алмаштырыңыз.
  • Ensure there are no obstructions or strong radio interference between the fob and the vehicle.
• Баскычтар катуу же жооп бербейт:
  • Check for debris or damage around the buttons.
  • Ensure the fob is properly assembled after battery replacement.

Кепилдик жана колдоо

Your KeylessOption key fob comes with a 90-day warranty from the date of purchase. This warranty covers manufacturing defects and ensures quality and peace of mind. If you experience any defects or issues within this period, please contact KeylessOption customer support for assistance or a replacement.

For further support or to inquire about specific programming details for your vehicle, please refer to your vehicle's owner's manual or visit the official KeylessOption webсайт.