DIGITEN G3/8 Water Flow Sensor (Model FL-308T) Instruction Manual

1. Продукт бүтүп калдыview

The DIGITEN G3/8 Water Flow Sensor (Model FL-308T) is a Hall effect flowmeter designed for precise liquid fluid measurement. It is suitable for various applications requiring flow monitoring, such as water heaters, water dispensers, water purifiers, and irrigation systems. This sensor provides a pulse signal output proportional to the water flow rate.

Figure 1: DIGITEN G3/8 Water Flow Sensor (Model FL-308T)

Негизги өзгөчөлүктөрү:

• Жеңил жана компакт дизайн.
• Stable performance with low water pressure start.
• Integrated Hall effect sensor for electrical pulse output.
• Constructed from food-grade plastic for safety and reliability.
• Waterproof, heat-resistant, pressure-resistant, and cold-resistant properties.

2. Техникалык шарттар

The following table details the technical specifications for the DIGITEN G3/8 Water Flow Sensor:

Figure 2: Sensor dimensions and key specifications

3. Орнотуу жана орнотуу

Proper installation is crucial for accurate readings and reliable operation of the water flow sensor.

3.1 Электр зымдары боюнча нускамалар

The sensor features a 3-wire connection. Connect the wires as follows:

• Кызыл зым: VCC (+) - Connect to the positive power supply (3-24V DC).
• Кара зым: GND (-) - Connect to ground.
• Сары зым: Signal Output - Connect to your microcontroller or reading device.

Figure 3: Sensor with wiring label

Figure 4: Sensor with electrical connector

3.2 Сантехниканы туташтыруу

The sensor uses G3/8 inch BSP (British Standard Pipe) threads. If connecting to NPT (National Pipe Taper) threads, it is recommended to use thread seal tape to ensure a watertight connection.

Ensure the sensor is installed with the correct flow direction. An arrow indicating the flow direction is marked on the sensor body. Align this arrow with the direction of water flow in your system.

Figure 5: Flow direction indicator on the sensor body

3.3 Жайгаштыруу маселелери

• Install the sensor in a section of pipe where the water flow is stable and free from turbulence.
• Avoid installing near pumps or valves that may cause sudden changes in flow or pressure.
• Ensure easy access for future maintenance or inspection.

4. Иштөө принциптери

The DIGITEN G3/8 Water Flow Sensor operates on the Hall effect principle. Inside the sensor, a small turbine wheel rotates as water flows through it. A magnet is attached to this turbine, and a Hall effect sensor detects the magnetic field changes as the magnet passes by. Each rotation of the turbine generates an electrical pulse.

The frequency of these pulses is directly proportional to the water flow rate. The relationship is given by the formula: F = 23 * Q, кайда:

• F is the pulse frequency in Hz.
• Q is the flow rate in Liters per Minute (L/Min).

By measuring the pulse frequency, you can calculate the instantaneous water flow rate. The sensor outputs a square wave pulse signal, which can be easily read by microcontrollers or other digital input devices.

5. Техникалык тейлөө

The DIGITEN G3/8 Water Flow Sensor is designed for low maintenance. However, periodic checks can help ensure its longevity and accuracy.

• Үзгүлтүксүз текшерүү: Periodically check for any leaks at the connection points.
• Туташуу бүтүндүгү: Ensure electrical connections remain secure and free from corrosion.
• Таштандыларды текшерүү: If flow readings become erratic or stop, inspect the sensor for any debris that might be obstructing the turbine's rotation. If necessary, disconnect the sensor and gently flush it with clean water. Avoid using harsh chemicals or abrasive tools.
• Сактагыч: If storing the sensor for an extended period, ensure it is clean, dry, and stored within the specified storage temperature and humidity ranges.

6. Кыйынчылыктарды

If you encounter issues with your DIGITEN G3/8 Water Flow Sensor, consider the following troubleshooting steps:

6.1 No Signal Output

• Кубат менен камсыздоону текшерүү: Verify that the sensor is receiving the correct operating voltage (3-24V DC) and that the ground connection is secure.
• Зымдарды текшерүү: Ensure all three wires (Red, Black, Yellow) are correctly connected to your system.
• Verify Flow: Confirm that water is actually flowing through the sensor. The sensor requires a minimum flow rate of 0.3 L/min to generate pulses.
• Ички тоскоолдук: If water is flowing but no pulses are detected, the internal turbine might be jammed by debris. Refer to the Maintenance section for cleaning instructions.

6.2 Туура эмес окуулар

• Агым багыты: Ensure the sensor is installed with the correct flow direction, aligning with the arrow on the sensor body.
• Stable Flow: Turbulent flow can affect accuracy. Try to install the sensor in a straight section of pipe away from elbows, valves, or pumps.
• Pulse Constant: Double-check your calculation using the pulse constant F = 23 * Q. Ensure your reading device is correctly interpreting the pulse frequency.
• Тtage Туруктуулук: Ensure the power supply to the sensor is stable and within the specified voltage диапазону.

7. Кепилдик жана колдоо

DIGITEN provides a one-year warranty for any product quality problems. If you experience any issues or require technical assistance, please contact DIGITEN customer support through the retailer where you purchased the product or visit the official DIGITEN webколдоо булактары үчүн сайт.

For further information or inquiries, please refer to the contact details provided with your purchase or on the DIGITEN brand store page.