SRAM Flat Mount 20F Rear Bracket Instruction Manual

1. Киришүү

This manual provides comprehensive instructions for the proper installation, maintenance, and troubleshooting of the SRAM Flat Mount 20F Rear Bracket. This component is designed to adapt your bicycle's flat mount brake system for a 160mm rear rotor, ensuring optimal braking performance and compatibility.

2. Коопсуздук маалыматы

ЭСКЕРТҮҮ:

• Always ensure all components are installed correctly and tightened to the manufacturer's specified torque values. Incorrect installation can lead to component failure, loss of control, and serious injury.
• If you are unsure about any installation step, consult a qualified bicycle mechanic.
• Regularly inspect the bracket and associated brake components for wear, damage, or loose fasteners.
• Do not modify the bracket or use it for purposes other than its intended design.

3. Пакеттин мазмуну

Төмөндө тизмеленген нерселердин баары пакетиңизде бар экенин текшериңиз:

• 1 x SRAM Flat Mount 20F Rear Bracket
• 2 x Stainless Bracket Mounting Bolts
• 2 x Washers (typically included with bolts)

Figure 3.1: SRAM Flat Mount 20F Rear Bracket shown with two mounting bolts and two washers.

4. Продукт бүтүп калдыview

The SRAM Flat Mount 20F Rear Bracket is a precision-engineered component designed to facilitate the use of a 160mm brake rotor on bicycle frames equipped with flat mount brake caliper interfaces. It is constructed from durable synthetic fiber and features a multi-color finish. The bracket effectively offsets the brake caliper to accommodate the larger rotor size, enhancing braking power and modulation.

5. Орнотуу жана орнотуу

Follow these steps for proper installation of the SRAM Flat Mount 20F Rear Bracket:

1. кадрды даярдоо: Ensure the flat mount interface on your bicycle frame is clean and free of debris.
2. Кронштейнди жайгаштырыңыз: Align the SRAM Flat Mount 20F Rear Bracket with the mounting points on your bicycle frame's rear chainstay or seatstay. The "REAR 160" marking on the bracket should be visible and oriented correctly.
3. Монтаждоо болттору: Insert the two stainless bracket mounting bolts through the bracket and into the frame's threaded inserts. If washers are provided, place them under the bolt heads.
4. Алгачкы бекемдөө: Hand-tighten the bolts to secure the bracket in place.
5. Install Brake Caliper: Mount your flat mount brake caliper onto the bracket using the appropriate caliper mounting bolts (not included with this bracket).
6. Акыркы момент: Using a torque wrench, tighten the bracket mounting bolts to the torque specifications provided by your bicycle frame manufacturer. Similarly, tighten the brake caliper mounting bolts to the brake caliper manufacturer's specifications. Refer to your frame and brake manuals for precise torque values.
7. Brake Alignment: After installation, ensure the brake caliper is properly aligned with the 160mm rotor. Adjust as necessary to prevent rotor rub and ensure optimal braking performance.

Эскертүү: Always refer to your bicycle frame and brake caliper manufacturer's instructions for specific torque values and alignment procedures.

6. Техникалык тейлөө

Regular maintenance will ensure the longevity and safe operation of your SRAM Flat Mount 20F Rear Bracket:

• Мезгилдүү текшерүү: Visually inspect the bracket for any signs of cracks, bends, or damage, especially after impacts or heavy use.
• Болт текшерүү: Periodically check the tightness of all mounting bolts (bracket to frame, and caliper to bracket) to ensure they remain at the specified torque. Loose bolts can lead to poor braking performance or component failure.
• Тазалоо: Keep the bracket and surrounding area clean from dirt, mud, and road grime. Use a mild soap and water solution, then rinse thoroughly and dry. Avoid harsh chemicals that could damage the finish or material.

7. Кыйынчылыктарды

If you encounter issues with your brake system after installing the bracket, consider the following:

• Rotor Rub: If the brake rotor rubs against the caliper pads, ensure the caliper is properly aligned. This often involves loosening the caliper mounting bolts slightly, squeezing the brake lever to center the caliper, and then re-tightening the bolts while holding the lever.
• Loose Braking: Check all bolts (bracket to frame, caliper to bracket) for proper torque. A loose bracket can cause inconsistent braking.
• адаттан тыш үндөр: Investigate any creaking or grinding noises. This could indicate loose components, contamination, or worn brake pads/rotor.

If problems persist, consult a professional bicycle mechanic.

8. Техникалык шарттар

9. Кепилдик жана колдоо

For warranty information or technical support regarding your SRAM Flat Mount 20F Rear Bracket, please refer to the official SRAM webсайтка же түздөн-түз кардарларды тейлөөгө кайрылыңыз. Ар кандай кепилдик дооматтары үчүн сатып алганыңыздын далилин сактаңыз.

SRAM расмий Webсайт: www.sram.com