1. Киришүү
This manual provides essential information for the safe and effective use of the HILTI 3511065 Adh ANC HY 100 Anchor System. Please read these instructions carefully before installation and operation.
The HILTI Adh ANC HY 100 is a high-performance adhesive anchor system designed for various fastening applications in concrete and masonry. It includes the HY 100 adhesive and is typically used with the HDE 500 dispenser tool.
2. Коопсуздук маалыматы
ЭСКЕРТҮҮ: Бул коопсуздук көрсөтмөлөрүн аткарбоо олуттуу жаракат алууга же өлүмгө алып келиши мүмкүн.
- Always wear appropriate personal protective equipment (PPE), including safety glasses, gloves, and respiratory protection, especially when handling chemical components.
- Иш зонасында шайкеш желдетүүнү камсыз кылыңыз.
- Балдар жетпеген жерде сактаңыз.
- Refer to the Safety Data Sheet (SDS) for detailed information on chemical components.
- Do not ingest. In case of contact with skin or eyes, rinse immediately with plenty of water and seek medical advice.
3. Компоненттер
The HILTI 3511065 Adh ANC HY 100 Anchor System typically includes the following components:
- HILTI HY 100 Adhesive Cartridge (16.9oz/500ml)
- Mixing Nozzles (2MC)
- HDE 500 Dispenser Tool (sold separately or as part of a kit)
- Anchor Rods or Rebar (not included, selected based on application)
Figure 1: HILTI HY 100 Adhesive Cartridge and HDE 500 Dispenser Tool. This image shows the adhesive cartridge and the tool used for dispensing it, essential components of the anchor system.
4. Орнотуу
- Prepare the Substrate: Drill a hole of the specified diameter and depth according to the anchor rod size and application requirements. Ensure the hole is clean, dry, and free of dust and debris. Use a brush and compressed air to thoroughly clean the drilled hole.
- Prepare the Adhesive Cartridge: Remove the cap from the HY 100 adhesive cartridge. Screw a new mixing nozzle firmly onto the cartridge.
- Load into Dispenser: Insert the prepared adhesive cartridge into the HDE 500 dispenser tool.
- Dispense Initial Material: Before injecting into the hole, dispense a small amount of adhesive onto a piece of cardboard or waste material until a consistent, uniformly mixed color is achieved. This ensures proper mixing of the two-component adhesive.
5. Иштөө нускамалары
- Inject Adhesive: Insert the mixing nozzle to the bottom of the drilled hole. Begin dispensing the adhesive while slowly withdrawing the nozzle, ensuring the hole is filled from the bottom up to approximately 2/3 full. Avoid trapping air.
- Insert Anchor Element: Immediately insert the anchor rod or rebar into the adhesive-filled hole with a slight twisting motion until it reaches the bottom.
- Айыруу убактысы: Observe the specified curing time (working time and full curing time) provided in the product technical data sheet, which varies based on ambient temperature. Do not load the anchor until full curing is achieved.
- Тазалоо: Clean any excess adhesive from the surface before it cures.
6. Техникалык тейлөө
- Dispenser Tool: After use, clean the HDE 500 dispenser tool thoroughly, especially the plunger and cartridge holder, to prevent adhesive buildup.
- Сактагыч: Store unused adhesive cartridges in a cool, dry place, away from direct sunlight and extreme temperatures. Ensure the cap is securely replaced on partially used cartridges (if applicable, though HY 100 is often single-use once mixed).
- Жоюу: Dispose of used cartridges and mixing nozzles according to local environmental regulations.
7. Кыйынчылыктарды
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Adhesive not mixing properly (streaky color) | Insufficient initial dispensing; clogged nozzle | Dispense more material until uniform color is achieved. Replace nozzle if clogged. |
| Anchor rod not fully seating | Hole too shallow; too much adhesive | Ensure correct hole depth. Do not overfill the hole (fill 2/3). |
| Adhesive cures too quickly/slowly | Incorrect ambient temperature | Refer to technical data sheet for temperature-dependent curing times. Adjust work pace accordingly. |
8. Техникалык шарттар
- Модел: 3511065
- Чаптама түрү: HY 100 (Hybrid Mortar)
- Cartridge Volume: 16.9 унция / 500 мл
- Dispenser Tool Compatibility: HDE 500
- Колдонмо температурасы: Refer to product technical data sheet for specific ranges.
- Айыруу убактысы: Varies with temperature; refer to technical data sheet.
9. Кепилдик жана колдоо
For warranty information and technical support, please contact HILTI directly.
HILTI Customer Service:
- Webсайт: www.hilti.com
- Байланыш маалыматы: Refer to the official HILTI webжергиликтүү байланыш номерлери жана колдоо параметрлери үчүн сайт.