ODI J30XTH-U

ODI ATV X-Treme Lock-On Grips

Model: J30XTH-U

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your ODI ATV X-Treme Lock-On Grips. Please read this manual thoroughly before installation and use to ensure proper function and longevity of your product.

Продукт бүттүview

The ODI X-Treme Lock-On Grips are engineered for optimal traction and control on ATVs. Featuring a unique design, these grips ensure a secure hold in various conditions.

Негизги өзгөчөлүктөрү:

  • Designed for optimal traction regardless of condition.
  • Tacky diamond plate pads provide exceptional grip.
  • Small 3/4 flange helps keep hands securely on the bars.
  • 100% slip-free performance guaranteed with ODI's Patented Lock-On system.
  • Available in 130mm length.
ODI ATV X-Treme Lock-On Grip, Graphite color

Image of the ODI ATV X-Treme Lock-On Grip, showcasing its design and texture. The grip features a diamond plate pattern for enhanced traction and a small 3/4 flange.

Орнотуу жана орнотуу

Proper installation is crucial for the performance and safety of your ODI Lock-On Grips. Follow these steps carefully:

  1. Prepare Handlebars: Ensure your ATV handlebars are clean and free from any old grip residue, dirt, or grease. Use a suitable cleaner if necessary and allow to dry completely.
  2. Remove Old Grips (if applicable): If replacing existing grips, carefully cut or slide off the old grips. Remove any old glue or adhesive.
  3. Install Throttle Side Grip: Slide the grip onto the throttle tube. Ensure the grip is fully seated against the throttle housing. The lock-on clamp should be positioned correctly.
  4. Install Clutch Side Grip: Slide the grip onto the clutch side of the handlebar. Ensure it is fully seated.
  5. Tighten Lock-On Clamps: Using an appropriate hex key, tighten the lock-on clamps on both grips. Do not overtighten; tighten until the grips are secure and do not rotate. Refer to your ATV's manual for specific torque specifications if available, or tighten firmly by hand.
  6. Test Grips: Before riding, ensure both grips are firmly in place and do not slip or rotate. Check throttle operation for smooth movement.

Эскертүү: Always ensure the throttle operates freely and returns to the idle position without obstruction after grip installation.

Иштөө нускамалары

The ODI X-Treme Lock-On Grips are designed for immediate use after proper installation. Their primary function is to provide a secure and comfortable interface between the rider and the ATV handlebars.

  • Коопсуз кармоо: The patented Lock-On system ensures the grips remain firmly in place, preventing unwanted rotation or slipping during aggressive riding.
  • Күчөтүлгөн тартуу күчү: The tacky diamond plate pattern provides superior grip, allowing for better control and reduced hand fatigue, especially in wet or muddy conditions.
  • Комфорт: The material and design are optimized for rider comfort, absorbing vibrations and providing a consistent feel.

No special operating procedures are required beyond standard ATV riding practices. Focus on maintaining a firm but relaxed grip for optimal control.

Техникалык тейлөө

Regular maintenance will extend the life and performance of your ODI X-Treme Lock-On Grips.

  • Тазалоо: Clean grips regularly with mild soap and water. Avoid harsh chemicals or solvents that could degrade the grip material. Rinse thoroughly and allow to air dry.
  • Текшерүү: Periodically inspect the grips for signs of wear, tears, or damage. Check the lock-on clamps to ensure they remain tight. If any damage is observed, consider replacing the grips for safety.
  • Сактагыч: When not in use for extended periods, store your ATV in a clean, dry environment away from direct sunlight and extreme temperatures to prevent material degradation.

Проблемаларды чечүү

If you encounter issues with your ODI X-Treme Lock-On Grips, refer to the following common problems and solutions:

КөйгөйМүмкүн себепЧечим
Grips rotate or slip on handlebars.Lock-on clampлар жетиштуу турде бекемделбеген.Камсыз кылуу clamps are tightened firmly with an appropriate hex key. Do not overtighten.
Grips feel loose after installation.Incorrect grip size for handlebars, or clampтолук кандуу ишке тартылган эмес.Verify grip size matches handlebar diameter. Re-install, ensuring grips are fully seated and clamps are properly engaged and tightened.
Reduced traction or worn surface.Normal wear and tear, or accumulation of dirt/oil.Clean grips thoroughly. If wear is significant, consider replacing the grips for optimal performance and safety.

Техникалык шарттар

Модель атыATV Xtreme Lock-On Grips
Бөлүмдүн номериJ30XTH-U
БрендODI (Old Dutch International)
Унаа кызматынын түрүATV
ТүсГрафит
Өлчөмү130мм
Элемент Салмагы0.35 фунт
Элементтердин саны2
UPC711484187766
Элементтин өлчөмдөрү (LxWxH)7.9 x 4.7 x 2.3 дюйм
Пакеттин өлчөмдөрү (LxWxH)8 x 8 x 3 дюйм

Кепилдик жана колдоо

For warranty information or technical support regarding your ODI ATV X-Treme Lock-On Grips, please contact the manufacturer directly. Details can typically be found on the official ODI webсайты же ыйгарым укуктуу дилериңиз аркылуу.

Сураныч, кепилдик дооматтар үчүн сатып алуу далилиңизди сактап коюңуз.

© 2024 ODI. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.