Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Global Door Control Push Bar Panic Exit Device with Exterior Lever Trim. This device is designed for emergency egress and secure entry, suitable for doors 30 to 36 inches wide. Please read this manual thoroughly before installation and use to ensure proper function and safety.
Коопсуздук маалыматы
- Орнотуу учурунда ар дайым коргоочу көз айнек жана кол кап сыяктуу тиешелүү жеке коргонуу шаймандарын (ЖКК) кийиңиз.
- Ensure the door frame and door material are suitable for the installation of this device.
- Орнотууну баштоодон мурун бардык компоненттердин бар экенин жана бузулбаганын текшериңиз.
- Do not modify the device. Unauthorized modifications can compromise safety and void the warranty.
- Тумчугуп калуу коркунучун болтурбоо үчүн кичинекей бөлүктөрүн балдардан алыс кармаңыз.
- Эгерде сиз орнотуу процессинин кайсы бир кадамы боюнча күмөн санасаңыз, квалификациялуу адиске кайрылыңыз.
Пакеттин мазмуну
Бардык компоненттерди кылдаттык менен таңгактан чыгарып, төмөнкү нерселерди алганыңызды текшериңиз:
- Push Bar Panic Exit Device (Main Bar Assembly)
- Exterior Lever Trim with Keyed Entry
- Strike Plate
- Dogging Key (or Pin)
- Installation Hardware (screws, fasteners, etc.)
- Орнотуу шаблоны (эгер камтылган болсо)
Сүрөт 1: Бүттүview of the Global Door Control Push Bar Panic Exit Device components. This image displays the main push bar assembly, the exterior lever handle with a keyhole, the strike plate for the door frame, and a small dogging pin. All components are finished in aluminum.
Орнотуу жана орнотуу
This device is reversible and non-handed, meaning it can be installed on both left-hand and right-hand doors. The panic bar can be cut to size to fit doors between 30 and 36 inches wide.
Керектүү куралдар:
- Бургулоо
- Өлчөө лентасы
- Карандаш же маркер
- Бурагычтар (Phillips жана Flathead)
- Hacksaw (if cutting the panic bar to size)
- Chisel (if mortising for the strike plate)
Орнотуу кадамдары:
- эшикти даярдоо: If necessary, measure your door width. The panic bar is designed for doors 30" to 36" wide. If your door is narrower than 36", you may need to cut the panic bar to the appropriate length. Refer to the included template for precise measurements and cutting instructions.
- Маркалоо жана бургулоо: Use the provided installation template to mark the positions for the mounting holes on both the door and the door frame. Ensure the template is level and correctly aligned. Drill pilot holes according to the template's specifications.
- Install Exterior Lever Trim: Install the exterior lever trim assembly on the outside of the door, aligning it with the pre-drilled holes. Secure it using the provided screws. Ensure the spindle or connecting mechanism passes through the door to engage with the panic device.
- Mount Panic Bar Assembly: Position the main push bar assembly on the interior side of the door, aligning it with the exterior lever trim's mechanism and the pre-drilled mounting holes. Secure the panic bar assembly firmly to the door using the appropriate hardware.
- Strike Plate орнотуу: Align the strike plate on the door frame with the latch bolt of the panic device. Mark the outline and screw holes. If required, mortise the door frame to ensure the strike plate sits flush. Secure the strike plate with screws.
- Сыноо операциясы: After installation, test the panic device and exterior lever thoroughly.
- From the inside, press the push bar to ensure the latch retracts smoothly and the door opens.
- From the outside, use the key to lock and unlock the exterior lever. Test the lever's operation when unlocked.
- Түзөтүүлөр: Make any necessary adjustments to ensure smooth operation and proper alignment. The device should operate freely without binding.
Иштөө нускамалары
Interior Operation (Emergency Egress):
To exit from the interior, simply push the horizontal bar (panic bar) firmly. This action retracts the latch bolt, allowing the door to open. The door will remain unlocked until the bar is released and the latch re-engages with the strike plate.
Exterior Operation (Entry):
To enter from the exterior, use the key to unlock the lever trim. Once unlocked, depress the lever handle to retract the latch bolt and open the door. The key can be removed in either the locked or unlocked position.
Dogging Feature:
The dogging feature allows the panic bar to remain in the retracted (unlocked) position, keeping the door unlocked for extended periods without needing to press the bar each time. This is useful for high-traffic situations where security is not a primary concern. To engage the dogging feature, depress the push bar and insert the dogging key (or pin) into the designated hole on the panic device, then turn or push to secure the bar in the retracted position. To disengage, reverse the process.
Техникалык тейлөө
- Тазалоо: Clean the aluminum surfaces with a soft, damp кездеме. Абразивдүү тазалагычтардан же эриткичтерден алыс болуңуз, анткени алар финишке зыян келтириши мүмкүн.
- Майлоо: Periodically apply a small amount of silicone-based lubricant to the moving parts of the latch mechanism and the key cylinder to ensure smooth operation. Do not over-lubricate.
- Текшерүү: Regularly inspect all screws and fasteners to ensure they are tight. Check for any signs of wear or damage to the panic bar, lever, or strike plate. Replace worn or damaged components immediately.
- Функционалдык тест: Test the panic device and exterior lever functionality monthly to ensure they operate correctly in case of an emergency.
Проблемаларды чечүү
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Panic bar is stiff or difficult to push. | Lack of lubrication, misalignment, or debris in mechanism. | Clean and lubricate moving parts. Check for proper alignment of the panic bar and strike plate. Remove any obstructions. |
| Exterior lever does not operate smoothly or key is difficult to turn. | Key cylinder needs lubrication, debris in cylinder, or internal mechanism issue. | Apply graphite lubricant to the key cylinder. Ensure the key is fully inserted. If issues persist, the lever trim may need replacement. |
| Эшик бекем жабылбайт. | Strike plate misalignment, worn latch bolt, or door sag. | Adjust the strike plate position. Inspect the latch bolt for wear. Check door hinges for sag and adjust if necessary. |
| Dogging feature does not engage/disengage. | Dogging mechanism obstructed or damaged. | Ensure the push bar is fully depressed when attempting to engage/disengage. Check for debris. If damaged, professional service may be required. |
Техникалык шарттар
- Модел: CMOBED-501-TH1100-LHEDAL
- Бренд: Global Door Control
- Материал: Алюминий
- Түсү: Алюминий
- Продукциянын өлчөмдөрү: 36"L x 3"W (Adjustable for doors 30" to 36" wide)
- Тышкы жасалгалоо: Алюминий
- Кулпу түрү: Key Lock (Exterior Lever)
- Колдун багыты: Ambidextrous (Reversible, Non-Handed)
- Өзгөчөлүктөр: Easy to Install, Keyed Entry, Dogging Feature
- Элемент Салмагы: Болжол менен 10.62 фунт
- Камтылган компоненттер: Орнотуу жабдыктары
- UPC: 703624961817
Кепилдик маалымат
Specific warranty details for the Global Door Control Push Bar Panic Exit Device are typically provided at the point of purchase or on the manufacturer's official website. Please retain your proof of purchase for warranty claims. Generally, products are warranted against defects in materials and workmanship under normal use for a specified period. For detailed terms and conditions, please refer to the documentation included with your product or contact Global Door Control customer support.
Кардарларды колдоо
If you have any questions, require assistance with installation, or need to report a problem with your Global Door Control Push Bar Panic Exit Device, please contact customer support. Contact information can usually be found on the manufacturer's website or on the product packaging. When contacting support, please have your model number (CMOBED-501-TH1100-LHEDAL) and proof of purchase readily available.