Rema Patch Kit Cement Only 5G - Instruction Manual

Продукт бүттүview

The REMA TIP TOP Cold Vulcanizing Fluid is an essential component for repairing bicycle, garden, car, truck, and tractor tubes. This 5-gram tube of cement is specifically designed to be used with REMA TIP TOP feather edge patches. When applied correctly, this fluid ensures that the tube patches stretch evenly in all directions, creating a perfect, durable bond and a seamless repair that maintains the integrity of the tube.

This image displays the Rema SVS-VULC cold vulcanizing fluid, packaged in a small, green tube. The tube has a black screw cap and is labeled with 'SVS-VULC', '5g/7ml', and 'Art.Nr. 505 9032'. The Rema Tip Top logo and 'ORIGINAL VULCANISATION' are also visible near the cap. This fluid is essential for creating a strong, seamless bond when repairing tubes with Rema Tip Top patches.

Орнотуу жана даярдоо

1. Locate the Puncture: Thoroughly inspect the tube to find the puncture. Mark the area clearly.
2. Аймакты тазалоо: Using a clean cloth, remove any dirt, grease, or moisture from around the puncture site. The area must be completely dry and free of contaminants for proper adhesion.
3. Roughen the Surface: Gently abrade the area around the puncture with sandpaper or a metal scraper. The roughened area should be slightly larger than the patch you intend to use. This creates a textured surface for the cement to adhere to.
4. Таштандыларды алып салуу: Wipe away any loose rubber particles or dust created during the roughening process. Ensure the surface is clean and dry before proceeding.

Operating Instructions (Applying the Cement)

1. Apply Cement: Squeeze a small amount of REMA TIP TOP Cold Vulcanizing Fluid onto the center of the prepared, roughened area.
2. Бир калыпта жайылтуу: Using the applicator tip or a clean, small brush, spread the cement thinly and evenly over the entire roughened area. Ensure the cement layer extends slightly beyond where the patch will sit.
3. Кургатууга уруксат: Allow the cement to dry completely. This is crucial for proper vulcanization. The cement will change from a wet, glossy appearance to a dull, matte finish. This typically takes 5-10 minutes depending on temperature and humidity. Do not touch the cement during this drying period.
4. Apply Patch: Once the cement is dry to the touch (no longer tacky), carefully peel the backing off your REMA TIP TOP feather edge patch. Avoid touching the adhesive side of the patch.
5. Катуу басыңыз: Center the patch over the puncture and press it down firmly onto the dried cement. Work from the center outwards to remove any air bubbles.
6. Дарылоо: Apply consistent pressure to the patch for several minutes to ensure maximum adhesion. A roller or the back of a spoon can be used for this. The repair is now complete.

Тейлөө жана сактоо

• Cap Tightly: After each use, ensure the cap is securely fastened to prevent the cement from drying out.
• Салкын, кургак жерде сактаңыз: Keep the tube in a cool, dry environment, away from direct sunlight, heat sources, and open flames.
• Кол жетпеген жерде сактаңыз: Балдар жана үй жаныбарлары жетпеген жерде сактаңыз.
• Check Expiration: While not explicitly stated, always check for any expiration dates on the packaging and dispose of expired product responsibly.

Проблемаларды чечүү

• Patch Not Sticking:
  • Ensure the tube surface was thoroughly cleaned and roughened.
  • Verify the cement was applied thinly and allowed to dry completely (to a dull, matte finish) before applying the patch.
  • Apply firm, even pressure to the patch after placement.
• Cement Dried in Tube:
  • Ensure the cap is tightly sealed after every use.
  • Салкын, кургак жерде сактаңыз.
• Bubbles Under Patch:
  • When applying the patch, start from the center and smooth outwards to push out any trapped air.
  • Ensure the cement layer is even and not too thick.

Техникалык шарттар

Кепилдик жана колдоо

For specific warranty information or technical support regarding REMA TIP TOP products, please refer to the official Rema Tip Top website or contact their customer service directly. Details are typically provided on the product packaging or through authorized distributors.

Always ensure you are using genuine REMA TIP TOP patches with this vulcanizing fluid for optimal repair results and to maintain product warranty, if applicable.