1. Киришүү
This manual provides instructions for the safe and efficient operation, setup, and maintenance of your SOMMER Pearl 4018 4018V000 TX55-868-4 garage door remote control. This device utilizes the SOMloq2 radio system and is compatible with Somloq Rollingcode systems, as well as Pro Teckentrup Drive models 4020, 4026, and 4031 Slider.
1-сүрөт: SOMMER Pearl 4018 4018V000 TX55-868-4 Remote Control. This image shows the compact, modern design of the remote control, featuring four buttons and a stainless steel application.
2. Коопсуздук маалыматы
- Keep the remote control out of reach of children to prevent accidental operation of the garage door.
- Балдардын пульт же гараждын эшигин ачуучу механизм менен ойношуна жол бербеңиз.
- Гараждын эшигин иштетүүдөн мурун, анын көрүнүп турганын жана тоскоолдуктардан таза экенин текшериңиз.
- Do not operate the garage door if people or objects are in its path.
- Батареяларды жергиликтүү эрежелерге ылайык жок кылыңыз. Батареяларды өрттөбөңүз.
- Avoid exposing the remote control to extreme temperatures, moisture, or direct sunlight.
3. Пакеттин мазмуну
Пакетиңизде бардык буюмдар бар экенин текшериңиз:
- SOMMER Pearl 4018 4018V000 TX55-868-4 Remote Control (quantity as purchased, typically 2 units)
- 3V CR2032 Lithium-metal battery (pre-installed or included)
4. Орнотуу жана программалоо
The SOMMER Pearl 4018 remote control must be programmed to your garage door opener receiver. The exact programming steps may vary slightly depending on your specific SOMMER garage door opener model. Refer to your garage door opener's manual for precise instructions. A common programming method is outlined below:
- Кабыл алуучуну табыңыз: Identify the garage door opener's motor unit. On the motor unit, locate the "Learn" or "Program" button. This button is often small and may be recessed.
- Үйрөнүү режимин иштетүү: Press and immediately release the "Learn" or "Program" button on your garage door opener. The indicator light on the opener will typically illuminate or flash, indicating it is in learn mode. You usually have about 30 seconds to complete the next step.
- Пультту программалоо: Within the learn mode timeframe, press and hold the desired button on your SOMMER Pearl 4018 remote control that you wish to use for operating the garage door.
- Программалоону ырастоо: Release the button on the remote control once the garage door opener's indicator light flashes or changes color, or if the garage door moves slightly. This indicates successful programming.
- Сыноо операциясы: Press the programmed button on your remote control to ensure it operates the garage door correctly.
- Программанын кошумча пульттары: Repeat these steps for any additional SOMMER Pearl 4018 remote controls you wish to program.
Note: If your garage door opener has a different programming procedure (e.g., using a master remote or a specific sequence), please consult your opener's manual.
5. Иштөө нускамалары
Once programmed, operating your SOMMER Pearl 4018 remote control is straightforward:
- Эшикти ачуу/жабуу: Press the programmed button on your remote control once. The garage door will begin to open or close.
- Эшикти токтотуу: Press the same programmed button again while the door is in motion to stop it.
- Көп эшиктер: If you have programmed multiple garage doors to different buttons on your remote, press the corresponding button for the desired door.
- Диапазон: The remote control has an approximate range of 50-140 meters, depending on environmental conditions and obstructions.
6. Техникалык тейлөө
6.1. Батареяны алмаштыруу
The SOMMER Pearl 4018 remote control uses a 3V CR2032 Lithium-metal battery. When the remote's range decreases significantly or it stops responding, it is likely time to replace the battery.
- C ачыңызasing: Алыстан башкаруу пультун c этияттык менен ачыңызasing. This usually involves prying it open with a small flat-head screwdriver or a similar tool at a designated notch.
- Эски батареяны алып салуу: Note the orientation of the old CR2032 battery (positive (+) side up or down). Gently remove the old battery.
- Жаңы батареяны салыңыз: Insert a new 3V CR2032 Lithium-metal battery, ensuring the correct polarity. The positive (+) side typically faces upwards.
- Жабуу Casing: Алыстан башкаруу пультун c баскычын басыңызasing кайра бекем бириктирилет.
- Сыноо: Test the remote control to ensure it functions correctly with the new battery.
6.2. Тазалоо
Clean the remote control with a soft, dry cloth. Do not use abrasive cleaners or allow moisture to enter the casing.
7. Кыйынчылыктарды
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Пульт иштебейт. | Батарея түгөндү же аз калды. | Replace the CR2032 battery (see Section 6.1). |
| Пульт иштебейт. | Remote is not programmed or programming was lost. | Reprogram the remote control to your garage door opener (see Section 4). |
| Кыскартылган иштөө диапазону. | Батарея аз. | Replace the CR2032 battery (see Section 6.1). |
| Кыскартылган иштөө диапазону. | Radio interference or obstructions. | Ensure there are no large metal objects or other radio-emitting devices between the remote and the receiver. Try operating from a different position. |
| Garage door opener not responding to remote. | Garage door opener is unplugged or has no power. | Check the power supply to your garage door opener. |
8. Техникалык шарттар
- Модел: Pearl 4018 4018V000 TX55-868-4
- Радио системасы: SOMloq2
- Баскычтар: 4
- Радио жыштык: FM 868.8 МГц, FM 868.95 МГц
- Диапазон: Approx. 50-140 meters (environment dependent)
- Өлчөмдөрү: 79 x 26 x 13 мм (3.11 x 1.02 x 0.51 дюйм)
- Батарея түрү: 3V CR2032 Lithium-metal
- Салмагы: 40 г (1.41 унция)
- Шайкештик: Somloq Rollingcode system, Pro Teckentrup Drive (compatible with 4020, 4026, 4031 Slider)
9. Кепилдик жана колдоо
For warranty information and technical support, please refer to the documentation provided with your original purchase or contact SOMMER customer service directly. Contact details can typically be found on the manufacturer's official webсайт.