FLIPSKY 2.4Ghz Remote VX1 for Electric Skateboard User Manual (V6 Version)

1. Киришүү

The FLIPSKY 2.4Ghz Remote VX1 is a wireless remote controller designed for DIY electric skateboards and longboards. It offers reliable 2.4Ghz bandwidth communication, multiple speed modes, and cruise control, enhancing the user's control and riding experience. This manual provides essential instructions for setup, operation, and maintenance of your VX1 remote.

Image: The FLIPSKY VX1 remote controller held in hand, with an electric skateboard visible in the background, illustrating its intended use.

2. Продукт бүтүп калдыview жана компоненттер

The VX1 remote system includes the remote controller and a receiver. Familiarize yourself with the components and their functions.

2.1 Кутуда эмне бар

• 2.4Ghz Remote VX1 Controller
• Алуучу
• USB заряддоо кабели
• Билек боо
• Receiver Connection Cables (for VESC4/VESC6/Non-VESC variants)

Image: All components included in the FLIPSKY VX1 remote package: the remote, receiver, various connection cables, a USB charging cable, and a wrist strap.

Image: Close-up of the USB charging cable and the wrist strap, essential accessories for the VX1 remote.

2.2 Алыстан башкаруучу өзгөчөлүктөрү

Image: A detailed diagram highlighting the features of the FLIPSKY VX1 remote, including the accelerate/braking trigger, power button, speed switching button, remote signal light, speed mode indication light, e-skateboard battery indication light, remote power indication light, and the USB charging port.

• Accelerate/Braking: Trigger for controlling speed and braking.
• Кубат баскычы: For turning the remote on and off.
• Ылдамдык которуу: Button to cycle through 3 speed modes.
• Remote Signal Light: Туташуу абалын көрсөтөт.
• Speed Mode Indication Light: Shows the currently selected speed mode.
• E-Skateboard Battery Indication Light: Displays the electric skateboard's battery level.
• Remote Power Indication Light: Shows the remote's internal battery level.
• USB кубаттоо порту: For recharging the remote's internal Li-ion battery.

3. Орнотуу нускамалары

3.1 Кабылдагычтын туташуусу

The VX1 remote comes with a receiver. Ensure correct connection to your Electronic Speed Controller (ESC) to prevent damage.

• Carefully check the receiver connection diagram corresponding to your specific FSESC (VESC4, VESC6, or Non-VESC). Incorrect wiring can damage the receiver.
• The variants (for VESC4/for VESC6/For Non VESC) only differ in receiver cables; the remote itself is the same.
• When using UART mode connection for the VX1 remote receiver, perform the connection кийин programming in VESC tool. This prevents interference with the programming process. In UART mode, no further remote adjustments are needed.

Image: The compact receiver board for the FLIPSKY VX1 remote, showing its various connection pins.

3.2 Pairing the Remote with Receiver(s)

Follow these steps to pair your VX1 remote with one or more receivers. This process ensures the remote and receiver communicate correctly.

1. Power on the remote: Кубат баскычын 1 секунд басыңыз.
2. Жупташтыруу режимине кирүү: Press the two small buttons on the remote simultaneously until the remote vibrates and the red LED blinks.
3. Power on the Skateboard/Receiver: Ensure the skateboard is powered off. Move the remote close to the receiver (within 0.3m). Power on the skateboard.
4. Жупташтыруу ырастоо: The signal light on the remote should stay solid green, and the receiver should show a solid blue LED after successful pairing.
5. For Multiple Receivers (Dual Motor Setup):
   1. Remove the first paired receiver.
   2. Repeat the pairing process (steps 1-4) for the second receiver.
   3. After both receivers are paired individually, connect both to check their status. Ensure both have solid blue LEDs.
6. PPM Input Setup (using VESC Tool):
   1. Unplug one receiver.
   2. Connect to VESC Tool and click "AutoConnect".
   3. Go to "App Setup Wizard" and select "Setup Input".
   4. Choose "PPM input, such as conventional RC receivers".
   5. Pull/push the throttle on the remote to its maximum and minimum positions. Click "Apply" to map the pulse length.
   6. Choose the desired control type (e.g., "Current No Reverse With Brake").
   7. Click "Write Configuration To Vesc" and then "Finish".
   8. Repeat the PPM input setup for the other receiver.
7. Акыркы тест: Connect both receivers and test them simultaneously with the remote to ensure synchronized operation.

4. Иштөө нускамалары

The VX1 remote offers intuitive control over your electric skateboard.

4.1 Күйгүзүү/өчүрүү

• Күйгүзүү: Press the power button for approximately 1 second. The green LED will light up.
• Өчүрүү: Press and hold the power button for approximately 2 seconds. The red LEDs will flash before turning off.

4.2 Ылдамдык режимдери

The remote supports 3 speed modes. Use the speed switching button to cycle through them, indicated by the speed mode indication lights.

4.3 Круиздик контрол

Activate cruise control mode for consistent speed without holding the throttle. Refer to your ESC's documentation for specific activation methods if not controlled directly by the remote.

4.4 Батареянын көрсөткүчү

The remote features indication lights for both the remote's battery volume and the e-skateboard's power level, allowing you to monitor power status during use.

4.5 Reverse Control

To engage reverse, apply full brake and then briefly press the pairing button. The remote will vibrate, and the wheels will spin in reverse. This function requires the remote receiver to communicate with the VESC using UART.

5. Техникалык тейлөө

• Заряддоо: The remote uses a rechargeable Li-ion battery. Charge it regularly using the provided USB cable. Avoid overcharging or completely draining the battery to prolong its lifespan.
• Тазалоо: Keep the remote clean and free from dust and debris. Use a soft, dry cloth for cleaning.
• Сактагыч: Store the remote in a dry, cool place when not in use.
• Билек боосу: Always use the wrist strap to prevent accidental drops during operation.

6. Кыйынчылыктарды

• Пульт жупташпай жатат: Ensure the remote and receiver are within 0.3m during pairing. Confirm both are powered on and the remote is in pairing mode (blinking red LED).
• Incorrect Receiver Connection: Double-check the wiring diagram for your specific FSESC version (VESC4, VESC6, or Non-VESC). Incorrect connections can cause damage.
• Issues with UART Mode: If using UART mode, ensure the receiver was connected кийин VESC tool programming. No remote adjustments are needed in UART mode.
• Сигналдын жоголушу: Ensure the remote is fully charged and within the 50-meter operating range.

7. Техникалык шарттар

8. Коопсуздук маалыматы

• Always wear appropriate protective gear, including a helmet, knee pads, and elbow pads, when operating an electric skateboard.
• Ensure the remote and skateboard are fully charged before each use.
• Regularly inspect your skateboard and remote for any signs of wear or damage.
• Operate the electric skateboard responsibly and in accordance with local laws and regulations.
• Avoid using the remote or skateboard in wet conditions or extreme temperatures.