1. Киришүү
This manual provides essential information for the safe and effective operation, setup, and maintenance of your Holzmann AKM610ECO Manual Sheet Metal Bender. Please read this manual thoroughly before assembly or operation to ensure proper use and to prevent injury or damage to the machine. Keep this manual in a safe place for future reference.
The Holzmann AKM610ECO is designed for bending sheet metal up to 600 mm in width and 1 mm in thickness, suitable for various metal fabrication tasks.
2. Коопсуздук нускамалары
ЭСКЕРТҮҮ: Бул коопсуздук көрсөтмөлөрүн аткарбоо олуттуу жаракат алууга же өлүмгө алып келиши мүмкүн.
- Ар дайым коопсуздук көз айнегин, кол капты жана бышык бут кийимди кошо алганда, тиешелүү жеке коргонуу каражаттарын (ЖКК) кийиңиз.
- Ensure the machine is securely mounted to a stable workbench or stand before operation.
- Keep hands and fingers clear of all moving parts, especially the bending and clamping jaws, during operation.
- Do not exceed the machine's specified bending capacity (1 mm thickness, 600 mm width). Exceeding capacity can damage the machine and cause injury.
- Даярдоо бөлүгүн туура clamped before initiating a bend to prevent slippage.
- Keep the work area clean and well-lit. Remove any clutter that could cause a tripping hazard.
- Do not operate the machine under the influence of drugs, alcohol, or medication that impairs judgment.
- Regularly inspect the machine for damage or wear. Do not operate a damaged machine.
- Бул жабдууну үйрөтүлгөн персонал гана иштетиши керек.
3. Пакеттин мазмуну
Upon unpacking, verify that all components are present and undamaged. If any parts are missing or damaged, contact your supplier immediately.
- Holzmann AKM610ECO Manual Sheet Metal Bender main unit
- Operating handles (2 units)
- Clamping handles/levers (2 units)
- Көрсөтмө (бул документ)
4. Орнотуу
Коопсуз жана натыйжалуу иштөө үчүн туура орнотуу абдан маанилүү.
- Пакеттен чыгаруу: Carefully remove all components from the packaging. Retain packaging for future transport if necessary.
- Монтаждоо: The bender must be securely mounted to a sturdy workbench or stand using appropriate bolts and fasteners (not included). Ensure the mounting surface can support the weight of the machine and the forces applied during bending.
- Attach Operating Handles: Insert the two main operating handles into their respective sockets on the bending beam. Secure them if necessary with set screws or pins provided.
- Clamping Handles: Insert the two clamping handles/levers into the clamping mechanism. These handles are used to secure the workpiece.
- Алгачкы текшерүү: Before first use, check all bolts and fasteners for tightness. Ensure all moving parts operate smoothly without obstruction.
5. Иштөө нускамалары
Follow these steps for safe and effective sheet metal bending.
- Жумушчу бөлүгүн даярдоо: Ensure the sheet metal is clean, free of burrs, and cut to the desired dimensions. Mark the bend line clearly.
- Clampбасым: Clamping mechanism can be adjusted to suit different material thicknesses. Use the adjustment knobs/bolts to set the appropriate pressure. The workpiece should be held firmly without deforming the material.
- Жумушчу бөлүгүнүн орду: cl көтөрүңүзamping bar using the clamping handles. Slide the sheet metal into position, aligning the bend line with the edge of the bending beam. Ensure the workpiece is centered and square.
- Clamp Жумушчу бөлүгү: Классты түшүрүүamping bar and firmly secure the workpiece by pushing down on the clamping handles. The metal must be held tightly to prevent slipping during the bend.
- Perform the Bend: Grasp both operating handles firmly. Slowly and steadily lift the bending beam upwards. Apply even pressure to both handles to ensure a consistent bend. Continue lifting until the desired angle is achieved.
- Release Workpiece: Once the bend is complete, carefully lower the bending beam back to its resting position. Release the clamping handles to free the workpiece.
- Inspect Bend: Examine the bent workpiece for accuracy and quality.
6. Техникалык тейлөө
Regular maintenance ensures the longevity and optimal performance of your sheet metal bender.
- Тазалоо: After each use, clean the machine, especially the bending and clamping surfaces, to remove metal shavings and dust. Use a brush or compressed air.
- Майлоо: Periodically apply a light machine oil to all pivot points and moving parts to ensure smooth operation and prevent rust.
- Текшерүү: Regularly check all bolts, nuts, and fasteners for tightness. Inspect the bending edges for wear or damage. Replace worn parts as necessary.
- Сактагыч: Store the bender in a dry, clean environment to prevent corrosion.
7. Кыйынчылыктарды
Бул бөлүм сиз кабылышы мүмкүн болгон жалпы көйгөйлөрдү карайт.
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Workpiece slips during bending. | Жетишсиз clampбасым. | Көбөйтүү clamping pressure using the adjustment knobs/bolts. Ensure the workpiece is clean and free of oil. |
| Inconsistent bend angle across the workpiece. | Uneven pressure on operating handles; workpiece not square. | Apply even pressure to both operating handles. Ensure the workpiece is properly aligned and square before clamping. |
| Difficulty in lifting the bending beam. | Exceeding material thickness capacity; lack of lubrication. | Ensure material thickness is within specifications. Lubricate pivot points. |
| Bending edges leave marks on the material. | Sharp edges on bending components; excessive clampбасым. | Inspect bending edges for burrs and smooth them if necessary. Reduce clamping pressure if possible. |
8. Техникалык шарттар
- Бренд: Holzmann
- Модел: AKM610ECO
- Өндүрүүчүнүн шилтемеси: HO-AKM610ECO
- Bending Width: 600 мм
- Max. Material Thickness: 1 mm (mild steel)
- Бирдиктер: 1 Бардыгы
- Amazon.com.be сайтында жеткиликтүү болгон күнү: 4-август, 2022-жыл
9. Кепилдик жана колдоо
Information regarding product warranty and customer support was not available in the provided product data. Please refer to the product packaging or contact your retailer or the manufacturer directly for details on warranty coverage and support services.