XtremepowerUS 12-inch Sand Filter Pump System (Model 75110-V) Instruction Manual

1. Киришүү

This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your XtremepowerUS 12-inch Sand Filter Pump System. Please read this manual thoroughly before attempting to install or operate the system. Keep this manual for future reference.

Figure 1: XtremepowerUS 12-inch Sand Filter Pump System in operation.

Коопсуздук чаралары

• Кандайдыр бир тейлөөнү же тейлөөнү аткаруудан мурун ар дайым электр кубатын ажыратыңыз.
• Ensure the system is installed on a level surface.
• Do not operate the pump dry. Ensure it is primed with water before starting.
• Иштеп жатканда балдарды насос жана чыпка системасынан алыс кармаңыз.
• This pump is not for use/sale in California.

2. Пакеттин мазмуну

Төмөндө саналып өткөн бардык компоненттер пакетиңизге камтылганын текшериңиз. Эгерде кандайдыр бир бөлүктөрү жок же бузулуп калса, кардарларды колдоо менен байланышыңыз.

2-сүрөт: пакетке киргизилген бардык компоненттер.

• Кум чыпкалоочу бак (12 дюйм)
• 0.75 HP Pool Pump
• 4 тараптуу көп порттуу клапан
• Басым өлчөгүч
• System Tray / Mounting Base
• Шланг адаптерлери
• Шлангдар жана Клamps
• Manual

3. Техникалык шарттар

Key technical specifications for the XtremepowerUS 12-inch Sand Filter Pump System:

Сүрөт 3: Продукциянын өлчөмдөрү.

4. Орнотуу жана орнотуу

Follow these steps carefully to assemble and install your sand filter pump system. Refer to the video for visual guidance.

4.1 Фильтр монтажы

1. Дренаждык форсунканы орнотуу: Place an O-ring onto the long side of the filter drain nozzle. Route the nozzle from inside the filter barrel and push it out through the bottom drain hole. Place another O-ring and secure it with the nut from outside the barrel. Insert an O-ring into the drain hole nozzle cap and screw it onto the nozzle.
2. Position Filter Assembly: Place the filter assembly inside the filter barrel. Position the funnel on top of the filter assembly, ensuring it is correctly inserted and centered within the barrel.
3. Фильтрдик каражаттар менен толтуруңуз: Fill the filter barrel with your chosen filter media (filter balls or sand) according to recommended guidelines. Remove the funnel after filling.
4. Install 4-Way Valve: Place an O-ring onto the 4-way valve. Position the valve on the upper part of the filter, ensuring the top of the filter assembly is properly inserted into the bottom of the valve. Ensure the valve pump opening aligns with the filter stand groove and the waste opening is oriented towards the drain nozzle. Secure the valve in place with the locking ring. Place the square nut on one side of each locking ring and tighten.
5. Басым өлчөгүчтү орнотуу: Secure the pressure gauge with plumber's tape. Remove the pressure gauge covering screw from the valve and screw the pressure gauge onto the valve.

4.2 Насос орнотуу

1. Position Pump on Base: Place the pump on top of the system tray (mounting base), aligning it with all four screw holes.
2. Бекем орнотуу негизи: Flip the mounting base over and insert all four nuts into the mounting spaces. Carefully flip the mounting base back.
3. Fasten Pump: Place the bolts into the screw holes and tighten all four bolts with a Phillips screwdriver to secure the pump to the base.
4. Install Pump Adapters: Put O-rings on the hose adapters and screw the hose adapters onto the pump outlet and inlet.

4.3 Шланг орнотуу

Бардык шланг clamps are securely tightened to prevent leaks. Verify O-rings are correctly seated.

1. Filter to Pump Connection: Шланг коюу clamp on the hose adapter from the valve opening marked 'PUMP'. Connect a hose to this adapter and then to the pump's inlet hose adapter. Tighten both hose clamps.
2. Pool Return to Valve Connection: Connect the hose from the pool's return inlet to the hose adapter from the valve opening marked 'POOL'. Ensure the O-ring on the hose adapter is not displaced during this process. Tighten the hose clamp.
3. Pool Main Drain to Pump Connection: Connect the hose from the pool's main drain to the hose adapter on the pump's outlet. Tighten the hose clamp.

5. Операция

The 4-way multi-port valve allows for different operational modes. Always ensure the pump is OFF before changing valve settings.

Figure 4: Multi-port valve settings.

Valve Modes:

• Фильтрация: This is the standard operating mode. Water is pumped from the pool, filtered through the sand media, and returned to the pool.
• Артка жуу: Used to clean the filter media. Water flow is reversed, flushing trapped debris out through the waste port. Perform backwash when the pressure gauge reading is 8-10 PSI above the clean filter reading.
• Чайкоо: After backwashing, this mode settles the filter media and removes any remaining dirt from the filter lines before returning to filtration mode.
• Таштандылар: Drains water directly from the pool, bypassing the filter. Useful for lowering pool water level or vacuuming heavy debris directly to waste.
• Кайра жүгүртүү: Circulates pool water without filtering.
• Кыш: Системаны кышка даярдоо үчүн колдонулат.

6. Техникалык тейлөө

Үзгүлтүксүз техникалык тейлөө чыпкалоо системаңыздын оптималдуу иштешин жана узак мөөнөттүү иштешин камсыз кылат.

6.1 Артка жуу

Backwash the filter when the pressure gauge indicates a rise of 8-10 PSI above its normal clean operating pressure. This typically means the filter media is saturated with debris.

1. Насосту өчүрүңүз.
2. Set the multi-port valve to 'BACKWASH'.
3. Turn on the pump and run until the water from the waste port runs clear (typically 1-2 minutes).
4. Насосту өчүрүңүз.
5. Set the multi-port valve to 'RINSE'.
6. Насосту күйгүзүп, 30-60 секунд иштетиңиз.
7. Насосту өчүрүңүз.
8. Set the multi-port valve back to 'FILTRATION'.
9. Turn on the pump to resume normal operation.

6.2 Cleaning the Pump Strainer Basket

The pump's strainer basket should be checked and cleaned regularly to prevent debris from entering the pump impeller.

Figure 5: Pump strainer basket.

1. Насосту өчүрүп, суунун агып кетишине жол бербөө үчүн бардык керектүү клапандарды жабыңыз.
2. Unscrew the clear lid of the strainer basket.
3. Себетти алып чыгып, чогулган таштандыларды бошотуңуз.
4. Rinse the basket thoroughly.
5. Replace the basket and securely screw the lid back on. Ensure the O-ring is properly seated to prevent air leaks.
6. Open valves and prime the pump if necessary before restarting.

6.3 Фильтрдик медианы алмаштыруу

Sand filter media typically lasts 3-5 years, depending on usage and water quality. Filter balls may require more frequent cleaning or replacement.

1. Насосту өчүрүп, электр розеткасынан ажыратыңыз.
2. Фильтр резервуарын толугу менен бошотуңуз.
3. Remove the multi-port valve.
4. Carefully remove the old filter media.
5. Rinse the inside of the tank.
6. Add new filter media, ensuring the standpipe is centered.
7. Reassemble the valve and reconnect all hoses.
8. Perform a backwash and rinse cycle before resuming normal filtration.

7. Кыйынчылыктарды

This section addresses common issues you might encounter with your sand filter pump system.

8. Кепилдик жана колдоо

For warranty information or technical support, please refer to the warranty card included with your product or visit the XtremepowerUS official webсайт. Сатып алуу квитанциясын кепилдик дооматтары үчүн сатып алуунун далили катары сактаңыз.