1. Киришүү
Thank you for choosing the CREWORKS Electric PCP Air Compressor Pump. This manual provides essential information for the safe and efficient operation, setup, and maintenance of your compressor. Please read this manual thoroughly before using the product and retain it for future reference.
This portable electric air compressor is designed to produce high pressures up to 4500 PSI (30 MPa / 300 BAR), featuring an adjustable auto-stop function for precise pressure control. It is suitable for various applications including filling PCP air rifles, paintball tanks, airsoft equipment, and for pressure leakage testing.
2. Коопсуздук нускамалары
ЭСКЕРТҮҮ: Failure to follow these safety instructions may result in serious injury, property damage, or death.
- Муздатуу системасы: ALWAYS ensure the water cooling system is properly set up and functioning before starting the compressor. An external bucket of cooling water is required. NEVER operate the machine without adequate cooling water. Monitor the digital thermometer to prevent overheating.
- Жогорку басым: This compressor generates extremely high pressure. Always wear appropriate eye protection and ensure all connections are secure before operation. Never point the air outlet at yourself or others.
- Электр коопсуздугу: Connect the compressor to a standard 110V 60Hz single-phase grounded outlet. Do not operate with damaged cords or plugs. Keep the compressor away from water and damp чөйрөлөр.
- Вентиляция: Ысыктын топтолушун алдын алуу жана абанын туура киришин камсыз кылуу үчүн компрессорду жакшы желдетилген жерде иштетиңиз.
- Балдар жана үй жаныбарлары: Балдарды жана үй жаныбарларын компрессордон алыс кармаңыз.
- Тейлөө: Perform maintenance only when the compressor is unplugged and depressurized. Refer to the maintenance section for proper procedures.
- Мунай деңгээли: Regularly check the oil level. Refill immediately if the level is low, using ISO VG46 or AW 46 lubricating oil.
3. Продукциянын компоненттери
Familiarize yourself with the main components of your CREWORKS Electric PCP Air Compressor Pump:
4. Орнотуу
Follow these steps for initial setup before operating the compressor:
- Таңгактан чыгаруу жана текшерүү: Carefully remove the compressor from its packaging. Inspect for any visible damage during transit. Ensure all accessories (air hose, nozzles) are present.
- Муздатуу системасына туташуу:
- Place an external bucket of clean water near the compressor.
- Connect the water inlet hose to the compressor's water inlet port and submerge the other end into the bucket.
- Connect the water outlet hose to the compressor's water outlet port and submerge the other end into the bucket, ensuring proper circulation.
- Ensure the water pump (if external) is ready for operation or that the self-contained cooling system is filled and ready.
- Майдын деңгээлин текшерүү: Locate the oil level sight glass (refer to Figure 3.2). The oil level should be between the minimum and maximum marks. If low, add ISO VG46 or AW 46 lubricating oil through the respirator (refueling hole) until the correct level is reached.
- Аба түтүгүн туташтыруу: Attach the 8mm air hose connector with the quick-connect fitting to the desired tank or device you intend to fill. Ensure a secure, leak-free connection.
- Кубат туташуу: Plug the compressor's power cord into a standard 110V 60Hz grounded electrical outlet.
5. Иштөө нускамалары
Орнотуу аяктагандан кийин, компрессорду иштетүү үчүн төмөнкү кадамдарды аткарыңыз:
- Каалаган басымды коюу: Rotate the knob on the adjustable pressure gauge (Figure 3.4) to set your target pressure. The compressor will automatically stop when this pressure is reached. The maximum pre-set pressure is 30 MPa (4500 PSI).
- Муздатуу системасын ишке киргизүү: If using an external water pump, activate it to ensure water circulation. If the system is self-contained, ensure it is ready.
- Компрессорду ишке киргизүү: Flip the power switch to the 'ON' position. The compressor will begin to fill the connected tank.
- Монитордун иштеши:
- Continuously monitor the pressure gauge to observe the filling progress.
- Observe the digital thermometer to ensure the compressor's temperature remains within safe operating limits. If the temperature rises too high, stop the compressor immediately and allow it to cool.
- Listen for any unusual noises or signs of leakage.
- Автоматтык токтотуу функциясы: The compressor will automatically shut off once the pre-set pressure is achieved.
- Өчүрүү:
- Turn off the compressor power switch.
- Depressurize the system by slowly opening the pressure relief screw.
- Disconnect the air hose from the tank.
- Turn off the cooling system.
6. Техникалык тейлөө
Компрессорду үзгүлтүксүз техникалык тейлөө анын узак мөөнөттүү иштешин жана оптималдуу иштешин камсыз кылат.
- Oil Change/Refill: Check the oil level before each use. Change the oil every 20-30 hours of operation or every 3 months, whichever comes first. Use ISO VG46 or AW 46 lubricating oil. To change, drain old oil from the oil outlet and refill through the respirator.
- Муздаткыч суу: Replace cooling water regularly, especially if it appears dirty or discolored. Ensure the cooling system is free from blockages.
- Тазалоо: Keep the exterior of the compressor clean and free of dust and debris. Use a dry cloth. Do not use harsh chemicals or solvents.
- Аба чыпкасы: Inspect and clean or replace the air filter as needed to ensure clean air intake.
- Сактагыч: When not in use, store the compressor in a dry, cool place, away from direct sunlight and moisture.
7. Кыйынчылыктарды
Жалпы маселелер жана алардын чечимдери үчүн бул бөлүмдү караңыз.
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Компрессор иштебейт | No power; Power switch off; Thermal overload activated | Check power connection; Turn on power switch; Allow compressor to cool down and reset. |
| Компрессор ысып кетет | Insufficient cooling water; Blocked water circulation; Prolonged operation | Ensure adequate cooling water and circulation; Check for blockages; Allow compressor to cool; Do not operate continuously for extended periods. |
| Каалаган басымга жетпейт | Air leak in connections; Pressure gauge setting too low; Worn piston rings | Check all hose connections for leaks; Adjust pressure gauge setting; Contact customer support for service. |
| Ашыкча ызы-чуу же титирөө | Loose components; Insufficient oil; Unit not on a stable surface | Inspect and tighten all fasteners; Check and refill oil; Place compressor on a firm, level surface. |
8. Техникалык шарттар
Key technical specifications for the CREWORKS Electric PCP Air Compressor Pump (Model SX-HPA3LSPUS):
| Өзгөчөлүк | Спецификация |
|---|---|
| Бренд | ЭКИПАЖДАР |
| Модель номери | SX-HPA3LSPUS |
| Тtage | 110 вольт |
| Power Source | Электр зымдары |
| Күч | 1.80 кВт |
| Макс басым | 4500 PSI / 30 МПа / 300 БАР |
| Иш жөндөмдүүлүгү | 50 л/мин |
| Заряддоо ылдамдыгы | 40-50 L/min (1.5 - 1.8 CFM) |
| Ызы-чуу деңгээли | 78 дБ төмөн |
| Майлоочу май | ISO VG46 or AW 46 |
| Элемент Салмагы | 45.6 фунт (болжол менен 18 кг) |
| Пакеттин өлчөмдөрү | 19 x 18.5 x 12 дюйм |
| Өзгөчө өзгөчөлүк | Adjustable Control with Auto-Stop |
| Камтылган компоненттер | Аба шлангдары, саптамалар |
9. Кепилдик жана колдоо
This CREWORKS Electric PCP Air Compressor Pump comes with a 1 жылдык кепилдик сатып алынган күндөн тартып өндүрүш кемчиликтерин жабуу.
For technical support, warranty claims, or replacement parts, please contact CREWORKS customer service. Please have your model number (SX-HPA3LSPUS) and purchase information ready when contacting support.
Байланыш маалыматы:
Please refer to the contact details provided with your product packaging or visit the official CREWORKS webакыркы колдоо маалымат үчүн сайт.