LIGE Magnetic Smartwatch Charger Instruction Manual

Introduction

This manual provides essential instructions for the safe and effective use of your LIGE Magnetic Smartwatch Charger. Please read this guide thoroughly before use to ensure optimal performance and longevity of your device.

Продукт бүттүview

The LIGE Magnetic Smartwatch Charger is designed to provide a convenient and secure charging solution for compatible LIGE smartwatches. It features a USB-A connector for power input and a magnetic charging module for connecting to your smartwatch.

Шайкештик

This magnetic charger is compatible with the following LIGE smartwatch models:

• LIGE 327S
• LIGE ST2S
• LIGE ST6
• LIGE ST4
• ЛИГЕ 1837
• ЛИГЕ 1841
• ЛИГЕ 1824
• ЛИГЕ 276
• ЛИГЕ 1839
• LIGE ST8
• ЛИГЕ 423
• LIGE ST10
• ЛИГЕ 467
• ЛИГЕ 468
• ЛИГЕ 1843

Маанилүү: The distance between the two charging pins on the magnetic module is 2.5 mm. Ensure your smartwatch has compatible charging contacts with this spacing.

Жайгашуу

1. Кубатка туташуу: Insert the USB-A end of the charging cable into a compatible USB power source, such as a computer's USB port, a USB wall adapter (recommended 5V/1A or 5V/2A), or a power bank.
2. Акылдуу саатты даярдоо: Ensure your LIGE smartwatch is clean and dry, especially around the charging contacts.
3. Заряддоочу түзүлүштү туташтырыңыз: Align the magnetic charging module with the charging contacts on the back of your smartwatch. The magnets will automatically snap the charger into place. Ensure the pins make proper contact with the smartwatch's charging points.

Operating Instructions (Charging)

1. Once the charger is securely connected to both the power source and your smartwatch, the smartwatch display should indicate that it is charging. This is typically shown by a battery icon with a charging animation or a percentage көбөйтүү.
2. Allow the smartwatch to charge until it reaches full capacity. Charging times may vary depending on the smartwatch model and its current battery level.
3. After charging is complete, gently detach the magnetic charger from your smartwatch and unplug the USB-A connector from the power source.

Техникалык тейлөө

• Тазалоо: Regularly clean the magnetic charging pins and the smartwatch's charging contacts with a soft, dry cloth to prevent dust or debris buildup, which can interfere with charging.
• Сактагыч: Кубаттоочу түзүлүштү колдонулбаган учурда салкын, кургак жерде, күндүн түз тийген нурларынан жана өтө жогорку температурадан алыс сактаңыз.
• Кабельге кам көрүү: Avoid sharp bends or excessive pulling on the cable. The cable is designed to withstand repeated bending, but proper care extends its lifespan.

Проблемаларды чечүү

Акылдуу саат кубатталбай жатат:

• Ensure the USB-A connector is fully inserted into the power source.
• Кубат булагынын иштеп турганын жана кубат берип жатканын текшериңиз. Башка USB портун же дубал адаптерин колдонуп көрүңүз.
• Check that the magnetic charging module is correctly aligned and securely attached to the smartwatch's charging contacts. The magnets should hold it firmly.
• Clean the charging pins on the cable and the contacts on the smartwatch to remove any dirt or corrosion.
• Confirm that your smartwatch model is listed as compatible with this charger (2.5 mm pin spacing).

Жай кубаттоо:

• Ensure you are using a suitable power adapter (e.g., 5V/1A or 5V/2A). Lower power output sources may result in slower charging.
• Өтө ысык же суук чөйрөдө кубаттоодон алыс болуңуз, анткени бул кубаттоонун натыйжалуулугуна таасир этиши мүмкүн.

Техникалык шарттар

Кепилдик жана колдоо

For warranty information or technical support, please refer to the documentation provided with your original smartwatch or contact the LIGE customer service directly. Keep your purchase receipt as proof of purchase.