Introduction
Welcome to the instruction manual for your new Red Visual Signal Indicator (Model: LEDS100-03-02). This device is designed to provide clear visual signaling for various applications, offering both continuous and flashing light modes. Please read this manual thoroughly before installation and operation to ensure safe, correct, and efficient usage of the product.
Коопсуздук маалыматы
Жалпы коопсуздук чаралары
- Always disconnect power before attempting any installation, maintenance, or repair procedures.
- электр менен жабдууну камсыз кылуу voltage matches the device's specifications (85V). Incorrect voltage блокту бузуп, коопсуздукка коркунуч келтириши мүмкүн.
- Do not expose the device to extreme temperatures, direct sunlight for prolonged periods, or excessive moisture. This product is not designed for submersible use.
- Consult a qualified electrician if you are unsure about any wiring or installation steps.
- Балдар жетпеген жерде сактаңыз.
Пакеттин мазмуну
Төмөндө тизмеленген нерселердин баары пакетиңизге камтылганын текшериңиз:
- 1 x Red Visual Signal Indicator (LEDS100-03-02)
- 1 х Инструкция (бул документ)
Жайгашуу
Индикаторду орнотуу
- Choose a stable, flat, and visible location for mounting the indicator. Ensure the surface can support the weight of the unit.
- Allow adequate space around the unit for proper ventilation and access for wiring.
- Secure the indicator firmly to the chosen surface using appropriate fasteners (not included). Ensure it is stable and will not vibrate loose.
Зымдар диаграммасы
The device operates on an 85V power supply. Follow the steps below for correct wiring:
- Ensure the power source is disconnected before beginning any wiring.
- Identify the power input terminals on the indicator.
- Connect the 85V power supply wires to the designated terminals. For AC power, polarity is generally not critical, but ensure connections are secure.
- If the unit has a mode selection switch for continuous or flashing operation, set it to your desired mode before applying power. Refer to any labels on the unit for specific switch positions.
This image shows the red visual signal indicator, featuring a translucent red dome atop a black cylindrical base. The dome has vertical ridges designed for light diffusion, enhancing visibility. This is the main unit that requires mounting and electrical wiring for operation.
Иштөө нускамалары
Күйгүзүлүүдө
Once the indicator is securely mounted and correctly wired, apply the 85V power to the circuit. The unit will immediately begin operating in its selected mode (continuous or flashing).
Иштөө режимдери
The LEDS100-03-02 supports two primary operation modes:
- Үзгүлтүксүз режим: The red light will remain steadily illuminated as long as power is supplied.
- Жаркылдаган режим: The red light will flash at a regular interval, providing an intermittent visual signal.
The selection between these modes is typically done via an internal switch or specific wiring configuration as detailed in the 'Setup' section. Ensure the desired mode is set before applying power.
Техникалык тейлөө
Тазалоо
To clean the exterior of the indicator, gently wipe it with a soft, dry, or slightly damp cloth. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the plastic housing and lens.
Текшерүү
Periodically inspect the unit for any signs of physical damage, such as cracks in the housing or lens. Check all wiring connections to ensure they remain secure and free from corrosion or fraying. Ensure the mounting remains stable and secure.
Проблемаларды чечүү
If you encounter issues with your Red Visual Signal Indicator, please refer to the following troubleshooting guide:
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Indicator Does Not Light Up | Электр энергиясы жок Туура эмес зымдар Ички күнөө | Verify 85V power is supplied to the unit. Бардык зымдардын туташууларынын тууралыгын жана коопсуздугун текшериңиз. If power and wiring are correct, the unit may be faulty; contact support. |
| Light is Dim or Flickering | Туруксуз электр энергиясы Бошоң байланыш Partial internal fault | Ensure the 85V power supply is stable and consistent. Бардык зымдарды туташтыргычтын бекемдигин текшериңиз. If the issue persists, the unit may have an internal fault; contact support. |
Техникалык шарттар
| Өзгөчөлүк | Деталь |
|---|---|
| Модел | LEDS100-03-02 |
| Бренд | Жалпы |
| Тtage | 85V |
| Түс | Кызыл |
| Иштөө режимдери | Continuous / Flashing |
| ASIN | B0CNRSC7PD |
| Биринчи жеткиликтүү күн | 10-январь, 2024-жыл |
Кепилдик жана колдоо
For information regarding product warranty, returns, or technical support, please refer to the terms and conditions provided by your retailer or contact the manufacturer directly. It is recommended to keep your purchase receipt or proof of purchase for any warranty claims.
