BIG RED T83505-2 Torin Pro Series Hydraulic Low Profile Floor Jack

Продукт бүттүview

The BIG RED T83505-2 Torin Pro Series Hydraulic Low Profile Floor Jack is engineered for general and heavy-duty industrial use, offering a substantial 3.5 ton (7,000 lb.) lifting capacity. Its low-profile design allows access under vehicles with minimal ground clearance, with a lift range extending from 3.25 inches to 22 inches. Constructed from high-strength steel with a rust-resistant powder-coated finish, this jack is built for durability. The dual pump system provides rapid lifting, making it efficient for various cars, trucks, and SUVs. Maneuverability is enhanced by two large steel casters and two 360-degree swivel casters. For safety, it incorporates a built-in overload system to prevent use beyond its rated capacity, and a wide stance ensures stability during operation.

Маанилүү коопсуздук маалыматы

WARNING: Read, understand, and follow all instructions and warnings before using this product. Failure to do so may result in property damage, serious injury, or death.

• Always use this jack on a hard, level surface.
• Номиналдык сыйымдуулуктан 3.5 тоннадан (7,000 фунт) ашпаңыз.
• This jack is a lifting device only. Immediately after lifting, support the vehicle with appropriate jack stands. Do not work under a vehicle supported only by the jack.
• Унаанын токтоп турган абалда экенин (же механикалык берүү үчүн тиштүү дөңгөлөктүн) жана кол тормозунун иштеп турганын текшериңиз. Көтөрүлбөй турган дөңгөлөктөрдү тосуңуз.
• Жүктү ээрдин борборуна коюңуз. Борбордон тышкары жүктөр домкраттын оодарылып кетишине алып келиши мүмкүн.
• Do not use the jack for purposes other than lifting vehicles.
• Keep hands and feet clear of moving parts and the area under the load.
• Көздү коргоочу каражаттарды кошо алганда, тиешелүү коопсуздук каражаттарын кийиңиз.
• Inspect the jack before each use. Do not use if damaged, altered, or leaking hydraulic fluid.
• Техникалык тейлөөнү же оңдоону квалификациялуу адистер гана жүргүзүшү керек.

Кутуда эмне бар

• 1 x BIG RED T83505-2 Hydraulic Low Profile Floor Jack
• 1 х тутка монтажы
• 1 х Колдонуучунун колдонмосу (бул документ)

Компоненттери жана өзгөчөлүктөрү

1-сүрөт: Фронт view of the BIG RED T83505-2 Floor Jack. This image shows the overall design, including the lifting arm, saddle, and front wheels.

2-сүрөт: Side view of the floor jack with the handle inserted. This perspective highlights the low-profile design and the handle's attachment point.

3-сүрөт: The floor jack in its fully lowered position, showcasing its minimal height for accessing low-clearance vehicles.

4-сүрөт: А деталдуу view of the dual pump mechanism and the robust springs, illustrating the quick lift system.

5-сүрөт: Close-up of the rear 360-degree swivel casters and the lifting saddle, designed for smooth positioning and secure load contact.

The jack features a large steel saddle for secure contact with the vehicle's lifting point, a long handle for leverage and control, and durable steel and swivel casters for easy movement. The dual piston quick lift pump significantly reduces the number of strokes required to lift a load.

Орнотуу жана баштапкы даярдоо

1. Пакеттен чыгаруу: Домкрат менен бардык компоненттерди таңгактан этияттык менен алып салыңыз. Жеткирүүдөгү кандайдыр бир бузулууларды текшериңиз.
2. Туткасы Ассамблеясы: Insert the handle into the handle socket on the jack. Align the holes and secure it with the provided screw or pin, ensuring it is firmly seated.
3. Purging Air from Hydraulic System (Bleeding):
   • With the jack fully lowered, remove the oil filler plug (usually a rubber stopper or screw on the hydraulic cylinder).
   • Pump the handle rapidly 10-15 times to remove any trapped air.
   • Май толтургуч сайгычты алмаштырыңыз.
   • Test the jack by lifting it to its full height and then lowering it completely. Repeat a few times. If the jack does not lift smoothly or reaches full height, repeat the bleeding process.

Иштөө нускамалары

1. Унааны даярдоо: Park the vehicle on a hard, level surface. Engage the parking brake and place the transmission in park (or lowest gear for manual). Block the wheels that are not being lifted to prevent accidental movement.
2. Джекти жайгаштырыңыз: Locate the vehicle manufacturer's recommended lifting points. Slide the jack under the vehicle, positioning the saddle directly under the designated lifting point. Ensure the jack is stable and the load is centered on the saddle.
3. Унааны көтөрүңүз: Close the release valve by turning the handle clockwise until it is firmly closed. Pump the handle up and down to raise the vehicle to the desired height. Lift only high enough to allow for the placement of jack stands.
4. Жек Стенддери менен бекемдеңиз: Immediately after lifting, place appropriately rated jack stands under the vehicle's designated support points. Ensure the vehicle is securely resting on the jack stands before proceeding. NEVER work under a vehicle supported only by the floor jack.
5. Унааны түшүрүңүз: Once work is complete and jack stands are removed (ensure they are clear of the vehicle), slowly open the release valve by turning the handle counter-clockwise. The vehicle will begin to lower. Control the lowering speed by adjusting how much you open the valve.
6. Remove the Jack: Once the vehicle is fully lowered and resting on its wheels, remove the floor jack.

6-сүрөт: The floor jack correctly positioned under a vehicle's front axle, with additional jack stands providing crucial support. Always use jack stands when working under a vehicle.

7-сүрөт: Башка view of the floor jack and jack stands in use, demonstrating proper vehicle support during maintenance or repair.

Техникалык тейлөө

• Майлоо: Periodically lubricate all moving parts, including the pivot points, casters, and handle mechanism, with light machine oil.
• Гидравликалык суюктук: Check the hydraulic fluid level every 6 months. With the jack fully lowered and on a level surface, remove the oil filler plug. The fluid level should be just below the filler hole. If low, add high-quality hydraulic jack oil (ISO VG 15 or equivalent). Do not use brake fluid or motor oil.
• Тазалоо: Keep the jack clean and free of dirt, grease, and debris. Wipe down the ram and pump plungers regularly.
• Сактагыч: Дат басуунун алдын алуу жана пломбанын иштөө мөөнөтүн узартуу үчүн домкратты таза, кургак жерде, кулпусун толугу менен артка тартып сактаңыз.
• Текшерүү: Before each use, inspect the jack for any signs of damage, wear, or leaks. Pay attention to welds, casters, and the hydraulic cylinder. Do not use a damaged jack.

Проблемаларды чечүү

Техникалык шарттар

Кепилдик маалымат

This BIG RED T83505-2 Torin Pro Series Hydraulic Low Profile Floor Jack includes a limited 1-year manufacturer warranty. This warranty covers defects in materials and workmanship under normal use. For warranty claims or further details, please refer to the warranty card included with your product or contact the manufacturer directly.

Кардарларды колдоо

For technical assistance, parts inquiries, or general support regarding your BIG RED T83505-2 Floor Jack, please contact Torin customer service. Have your model number (T83505-2) and purchase information ready when contacting support.

Please note: Contact information for the manufacturer is typically provided on the product packaging or within the included warranty documentation.