CENTURY AOKE DC 12V-36V 315MHz 4-Channel Wireless Remote Control Switch User Manual

1. Киришүү

This manual provides detailed instructions for the installation, operation, and maintenance of the CENTURY AOKE DC 12V-36V 315MHz 4-Channel Wireless Remote Control Switch. This device is designed for various wireless control applications, offering reliable and flexible control over electrical systems.

Сураныч, туура иштешин жана коопсуздугун камсыз кылуу үчүн орнотуу жана колдонуудан мурун бул колдонмону кылдат окуп чыгыңыз.

2. Коопсуздук маалыматы

• Ensure the power supply is disconnected before any installation or wiring to prevent electric shock.
• Киргизилген томtage matches the receiver's specifications (DC 12V-36V).
• Do not exceed the maximum load current of 10A for the receiver.
• Аппаратты суудан, нымдан жана экстремалдык температурадан алыс кармаңыз.
• Монтаждоо жана тейлөөнү квалификациялуу кызматкерлер гана аткарышы керек.
• This device is not intended for life-support systems or other applications where device failure could result in injury or death.

3. Пакеттин мазмуну

Пакет төмөнкү нерселерди камтыйт:

• 1 x Receiver Unit (Wireless 4 Channels Remote Controller)
• 2 x Transmitter Units (4-Button Remote Controls)

4. Техникалык шарттар

Receiver Unit (Model: AK-C211008)

Transmitter Unit (Remote Control)

1-сүрөт: Receiver Unit Dimensions. The unit measures approximately 95mm in length, 62mm in width, and 28mm in height.

5. Орнотуу жана зымдар

Before wiring, ensure the power supply is completely disconnected. Refer to the wiring diagrams below for correct connections based on your application.

5.1. Output 12-36V Voltage Wiring диаграммасы

2-сүрөт: Output 12-36V Voltage Wiring. Connect your DC 12-36V power input to the receiver's input terminals. Connect your loads to the ON (Normally Open) and COM (Common) terminals for each channel. The NC (Normally Closed) terminal can also be used depending on the desired circuit behavior.

5.2. Output Switch Signal Wiring Diagram

3-сүрөт: Output Switch Signal Wiring. This diagram shows how to use the receiver to provide a dry contact switch signal. Connect the DC12-36V input power. The output terminals (ON, COM, NC) act as a switch, controlling an external circuit without directly powering the load from the receiver's output.

5.3. DC 12-36V Motor Wiring Diagram

4-сүрөт: DC 12-36V Motor Wiring. This diagram illustrates how to connect two DC motors for directional control. Input DC 12-36V power is supplied. Each motor (M) is connected across two channels, allowing for forward and reverse operation or independent control.

6. Иштөө режимдери

The receiver supports six different operating modes, which can be changed using the learning button on the receiver board. The modes determine how the receiver responds to button presses on the remote control.

6.1. Momentary Mode (Jog Mode)

Press the learning button once. When a remote button is pressed, the relay turns ON. When the remote button is released, the relay turns OFF.

6.2. Toggle Mode (Self-Locking Mode)

Press the learning button twice. When a remote button is pressed, the relay turns ON. Press the same button again, and the relay turns OFF.

6.3. Latch Mode (Interlock Mode)

Press the learning button three times. When a remote button is pressed, the corresponding relay turns ON, and all other relays turn OFF. This mode ensures only one relay is active at a time.

6.4. 2-Channel Momentary + 2-Channel Latch Mode

Press the learning button four times. Channels 1 and 2 operate in Momentary mode. Channels 3 and 4 operate in Latch mode.

6.5. 2-Channel Momentary + 2-Channel Toggle Mode

Press the learning button five times. Channels 1 and 2 operate in Momentary mode. Channels 3 and 4 operate in Toggle mode.

6.6. 2-Channel Toggle + 2-Channel Latch Mode

Press the learning button six times. Channels 1 and 2 operate in Toggle mode. Channels 3 and 4 operate in Latch mode.

7. Learning and Clearing Remote Codes

The receiver needs to "learn" the codes from your remote control transmitters to function. You can also clear all learned codes if needed.

7.1. Learning a Remote Control

1. Press the learning button on the receiver board the number of times corresponding to your desired operating mode (e.g., once for Momentary, twice for Toggle, etc.). The indicator light on the receiver will flash and then turn OFF.
2. Release the learning button.
3. Press any button on your remote control transmitter.
4. The indicator light on the receiver will flash three times, indicating that the learning process was successful.

Эскертүү: You must press the learning button the correct number of times for the desired mode before pressing the remote button.

7.2. Clearing All Remote Codes

1. Press and hold the learning button on the receiver board for approximately 8 seconds.
2. The indicator light will flash several times and then turn OFF.
3. Release the learning button.
4. Press any button on your remote control. The relay should not respond. This confirms that all codes have been successfully cleared.

8. Тиркемелер

This wireless remote control switch is versatile and can be used in a wide range of applications, including but not limited to:

• Anti-theft alarm control systems
• Electric doors and gates
• Көтөрүүчү жабдуулар
• LED жарык башкаруу
• Лифттер
• Electric curtains and roller shutters
• Гараждын эшигин ачкычтар
• Кирүүнү башкаруу системалары
• Industrial control systems
• Automotive applications (e.g., car alarms, remote start)
• Household switches

5-сүрөт: Application Scenarios. The remote control switch can be integrated into various systems for wireless control, such as garage doors, electric vehicles, cranes, and household appliances.

9. Кыйынчылыктарды

10. Техникалык тейлөө

• Тазалоо: Use a soft, dry cloth to clean the receiver and remote control. Do not use liquid cleaners or solvents.
• Батареяны алмаштыруу: Replace the remote control battery when the operating range decreases or the indicator light on the remote becomes dim.
• Экологиялык шарттар: Ensure the receiver is installed in a dry environment, protected from direct sunlight, rain, and extreme temperatures.
• Туташуу текшерүүлөрү: Мезгил-мезгили менен бардык зымдарды байланыштарды текшерип туруңуз, алар бекем жана коррозиядан таза.

11. Кепилдик жана колдоо

This product comes with a standard manufacturer's warranty. For specific warranty details, please refer to the product packaging or contact your retailer. If you encounter any issues or require technical assistance, please contact CENTURY AOKE customer support through the retailer's platform or their official webсайт.

Please provide your product model number (AK-C211008) and a detailed description of the issue when seeking support.