VIMIN 10G PCI-E Network Card (Model AQC113) Instruction Manual

Introduction

This manual provides detailed instructions for the installation, configuration, and use of your VIMIN 10G PCI-E Network Card. Please read this manual thoroughly before installation to ensure proper operation and to maximize the performance of your network adapter.

Негизги өзгөчөлүктөрү

• 10Gbps RJ45 Copper Port: Equipped with a Marvel AQC113 chipset, offering up to 10Gbps network speed for reliable high-speed data transfer.
• Rapid High-Speed Transmission: Supports PCIe 3.0 x4 bus interface, converting PCIe X4/X8/X16 slots into 10G RJ-45 Ethernet ports for efficient data transfer.
• Multi-Purpose Compatibility: Supports various data rates including 10Gbps, 5Gbps, 2.5Gbps, 1Gbps, and 100Mbps Ethernet connections with intelligent auto-negotiation.
• Flexible Bracket Adaptability: Includes both low-profile and standard brackets for compatibility with diverse computer chassis.
• Seamless System Support: Compatible with Windows 10/11, Windows Server, and Linux operating systems. Drivers are provided via a USB drive.
• Protocol Standard Compliance: Compliant with IEEE 802.3an, IEEE 802.3bz, IEEE 802.3ab, IEEE 802.3u, IEEE 802.3x, IEEE 802.3az, IEEE 802.1Q standards.

Пакеттин мазмуну

• 1 x VIMIN 10G PCI-E Network Card (AQC113)
• 1 x Standard Profile Bracket (pre-installed)
• 1 x Low-Profile кашаа
• 1 x Driver USB Drive
• 1 x Quick Installation Guide (This manual serves as a detailed guide)

Аппараттык орнотуу

1. Компьютериңизди өчүрүп, электр кабелин ажыратыңыз.
2. Компьютердин корпусун ачыңыз.
3. Locate an available PCI Express x4, x8, or x16 slot on your motherboard.
4. Remove the corresponding slot cover from the computer chassis. If necessary, replace the standard bracket on the network card with the low-profile кашаа.
5. Carefully insert the VIMIN 10G PCI-E Network Card into the chosen PCIe slot until it is firmly seated.
6. Secure the network card with a screw to the computer chassis.
7. Компьютердин корпусун жаап, кубат кабелин кайра туташтырыңыз.
8. Connect an Ethernet cable to the RJ45 port on the network card.

This image illustrates the three main steps for hardware installation: 1. Opening the chassis and removing the slot limiter. 2. Inserting the PCIe card into the slot. 3. Securing the bracket with screws.

The network card comes with both standard and low-profile brackets to fit various computer cases. It is compatible with PCI Express x4, x8, and x16 slots.

Драйверди орнотуу

Аппараттык камсыздоону орноткондон кийин, сиз иштөө тутумуңузга ылайыктуу драйверлерди орнотушуңуз керек.

1. Start your computer.
2. Insert the provided USB drive containing the drivers.
3. Navigate to the USB drive and locate the driver folder corresponding to your operating system (Windows, Linux).
4. Follow the on-screen instructions to install the drivers. For Windows, run the setup executable. For Linux, consult the README file within the driver folder for specific commands.
5. Драйверди орнотуу аяктагандан кийин компьютериңизди өчүрүп күйгүзүңүз.

Эскертүү: In some cases, especially with newer Linux distributions, the driver may be automatically recognized and installed by the system.

Операциялык системанын шайкештиги

The VIMIN 10G PCI-E Network Card supports a wide range of operating systems:

• Windows 10
• Windows 11
• Windows Server (various versions)
• Linux (ар кандай дистрибутивдер)
• VMware

This network card is compatible with Windows 10/11, Windows Server, and Linux operating systems.

Техникалык мүнөздөмөлөр

Проблемаларды чечүү

No Network Connection After Installation

• Verify Hardware Installation: Ensure the network card is fully seated in the PCIe slot and securely fastened.
• Кабель туташуусун текшерүү: Confirm the Ethernet cable is properly connected to both the network card and your router/switch.
• Драйверди орнотуу: Make sure the correct drivers for your operating system have been installed. Refer to the "Driver Installation" section.
• Түзмөк менеджери (Windows): Check Device Manager to see if the network card is recognized and if there are any error symbols (e.g., yellow exclamation mark). Reinstall drivers if necessary.
• BIOS/UEFI Орнотуулары: Ensure the PCIe slot is enabled in your system's BIOS/UEFI settings.

Slow Network Speeds

• Кабелдин сапаты: Use a high-quality Cat6a or Cat7 Ethernet cable for 10Gbps connections. Lower category cables may limit speed.
• Router/Switch Compatibility: Ensure your network router or switch supports 10Gbps speeds on the connected port.
• Драйвер жаңыртуулары: Check for the latest drivers from the VIMIN website or the provided USB drive.
• Системалык ресурстар: High CPU usage or insufficient RAM on your computer can affect network performance.

Card Not Detected in Windows 11

• PCIe Slot өткөрүү жөндөмдүүлүгү: Some motherboards share bandwidth between PCIe slots and M.2 NVMe slots. If the card is not detected, try moving it to a different PCIe slot or temporarily removing other M.2 devices to check for conflicts.
• Manual Driver Update: If the card appears in Device Manager but has issues, try manually updating the driver by searching for the Intel 10 Gigabit Ethernet driver pack and pointing Device Manager to the extracted driver files.

Кепилдик жана техникалык колдоо

The VIMIN 10G PCI-E Network Card comes with a 1-year after-sale service.

For technical assistance, troubleshooting, or warranty inquiries, please contact our support team:

• Электрондук почта: support@vimintech.com
• Онлайн колдоо: Visit the official VIMIN webКөп берилүүчү суроолор жана кошумча ресурстар үчүн сайт.

VIMIN offers dedicated customer support via email at support@vimintech.com, backed by a professional technical team providing 24-hour service.

Коопсуздук маалыматы

• Always power off your computer and disconnect the power cable before installing or removing any internal components.
• Handle the network card by its edges to avoid touching the gold-plated connectors or sensitive components.
• Use appropriate anti-static precautions (e.g., anti-static wrist strap) to prevent electrostatic discharge (ESD) damage.
• Ensure proper ventilation within your computer case to prevent overheating, especially for high-performance components.
• Do not attempt to modify or repair the device yourself. Refer to qualified personnel for service.

Продукт бүттүview Video