Aideepen 1200W 20A DC-DC Boost Converter Instruction Manual

1. Коопсуздук боюнча маанилүү маалымат

To prevent product damage due to incorrect operation, please read these instructions and precautions carefully before using this device. Improper use can lead to component failure or short circuits.

• Кубатты колдонуудан мурун бардык туташуулар туура экенин текшериңиз.
• Do not exceed the maximum input or output current and voltage рейтинги.
• Avoid short-circuiting the output during current adjustment.
• Do not attempt to charge supercapacitors with this device.
• The module can generate heat; ensure adequate ventilation. The fan activates automatically at approximately 40°C.

2. Продукциянын өзгөчөлүктөрү

This Aideepen 1200W 20A DC-DC Boost Converter offers enhanced performance and safety features compared to previous models:

• Extended Parameter Range: Supports a wider input and output voltage range, suitable for diverse applications.
• Optimized Circuit Design: Features an improved circuit with a MOS tube for rapid shutdown, enhancing output voltage stability and preventing failures or short circuits.
• Жакшыртылган муздатуу: The fan activation temperature has been lowered for more effective heat dissipation.
• Improved Current Handling: High current paths are reinforced with tin windows and constant resistance detection for stable operation under high current loads.
• Көптөгөн коргоо механизмдери: Includes input reverse polarity protection and adjustable undervoltage protection (UVP) to prevent overload and damage.
• User-Replaceable Fuse: Equipped with a safety fuse that can be replaced by the user if it blows.
• Туруктуу ток (ТК) режими: Features an adjustable CC potentiometer for precise output current control, ideal for constant current loads like LEDs or battery charging.

3. Продукттун спецификациялары

4. Орнотуу жана зымдар

Follow these steps for proper setup and wiring of the boost converter:

1. Initial Undervoltage Protection (UVP) Adjustment: Before connecting any load, adjust the UVP potentiometer (labeled 'UVP' on the board) to its minimum setting. This prevents premature shutdown during initial setup.
2. Output Voltage Орнотуу: Connect the input power (DC 14-85V) to the VIN+ and VIN- terminals. Then, adjust the CV (Constant Voltage) potentiometer (labeled 'CV' or 'Output Voltage Adjustment') to set the desired output voltage. Эскертүү: Output voltage must always be higher than the input voltage for boost operation. For 120V output, the input voltage 20V жогору болушу керек.
3. Constant Current (CC) Setting (for Constant Current Loads): If you are using a constant current load (e.g., an LED lamp or battery charging), first adjust the CC (Constant Current) potentiometer (labeled 'CC' or 'Output Current Regulation') to its minimum setting. Then, connect your load. Gradually increase the CC potentiometer until the desired output current is reached. Маанилүү: жүк тtage киргизилген көлөмүнөн жогору болушу керекtage for the boost power supply to operate correctly. For example, a 12V input can only charge 24V or higher batteries; a 24V input can only charge 36V or higher batteries.
4. Күйгүзүү ырааттуулугу: After setting both voltage and current, first turn on the boost power supply, then connect the load.

1-сүрөт: Wiring and Function Diagram. This image shows the input (VIN+, VIN-) and output (OUT+, OUT-) terminals, the CV (Output Voltage Adjustment) and CC (Output Current Regulation) potentiometers, and indicators for output voltage, overcurrent protection, and undervoltage коргоо.

5. Operating Notes and Performance Considerations

• Тtage Extremes: Avoid operating the converter at the absolute highest or lowest input and output voltage limits simultaneously for prolonged periods.
• Operating Current Calculation: The operating current must not exceed the maximum input current of 20A. Calculate the operating current using the formula:
  Operating Current = (Output Voltage * Output Current) / (Input Voltage * 0.94)
  (Where 0.94 represents an approximate efficiency of 94% for calculation purposes, as 1.06 is the loss factor).
  Exampле: For a 1200W model, if input is 15V, output is 48V, and load current is 5A: (48V * 5A) / (15V * 0.94) = 240W / 14.1V ≈ 17.02A. This is below 20A, so it can operate normally. If the load is 48V 7A: (48V * 7A) / (15V * 0.94) = 336W / 14.1V ≈ 23.83A. This exceeds the 20A input limit, so it cannot be used.
• Натыйжалуулугу: Efficiency is highest when the difference between input and output voltage is small. A larger voltage difference results in lower efficiency. For instance, with a 20V input and 120V output, efficiency will be at its lowest, potentially below 90%. Ensure the input power source can supply at least 1.5 times the required load power.
• Учурдагы тууралоо: It is strictly forbidden to adjust the output current by short-circuiting the output terminals. This can damage the module.
• Supercapacitors: Charging supercapacitors is strictly forbidden.
• Күйөрман операциясы: The cooling fan is temperature-controlled and will only activate when the heatsink temperature reaches approximately 40°C. It is normal for the fan to be off at lower temperatures.
• Power Output Limitations: The advertised 1200W output is theoretical. Due to the 20A input current limit, the actual maximum output power depends on the input voltagд. Мисалы үчүнample, with a 14V input, the maximum input power is 14V * 20A = 280W. After conversion losses, the practical maximum output power will be around 250W. It is recommended not to exceed 210W output when the input is 14V to ensure stable operation and longevity. To achieve higher output power, a higher input voltage (e.g., above 64V for maximum output) is required.

6. Продукциянын өлчөмдөрү

2-сүрөт: Product Dimensions. The module measures 13.0 cm in length, 6.2 cm in width, and 5.2 cm in height (including the fan and heatsink). The net weight is 294g.

3-сүрөт: Жогорку жана төмөнкү View. This image displays the top of the converter with its components and the bottom with the heatsink and fan assembly.

7. Пакеттин мазмуну

Пакетке төмөнкүлөр кирет:

• 1 x Aideepen 1200W 20A DC-DC Boost Converter Module
• 1 x Accessory kit (including bolts and spare fuse)

8. Кыйынчылыктарды

• No Output Voltage: Verify input power is within 14-85V. Ensure the output voltage setting is higher than the input voltage. Check for correct wiring.
• Output Current Cannot Be Adjusted: Ensure you are not attempting to adjust current by short-circuiting the output. Adjust the CC potentiometer with a proper load connected.
• желдеткич иштебейт: The fan is temperature-controlled and will only activate when the heatsink reaches approximately 40°C. If the module is cool, the fan will not run. If the module is hot and the fan is still not running, check fan connections.
• Lower Than Expected Output Power: Review the operating current calculation in Section 5. Ensure your input voltage is sufficient for the desired output power, considering the 20A input current limit and efficiency losses. Increase input voltage if possible, or reduce load.
• Модулдун ысып кетиши: Ensure adequate ventilation around the module. Check if the load exceeds the module's capabilities for the given input voltage.

9. Колдоо

If you encounter any issues or have questions regarding the Aideepen 1200W 20A DC-DC Boost Converter, please contact Aideepen customer support for assistance.