TREE REMO-R Universal Indicator User Manual

Tree® Professional Weighing Equipment products are simple to operate. Nevertheless, you should read through these operating instructions in their entirety, so that you can make optimum use of the full potential of the weighing scale in your daily work activities.

Бул колдонуу нускамаларында пиктограммалар жана клавиатура диаграммалары түрүндөгү көрсөтмөлөр бар, алар керектүү маалыматты табууга жардам берет:
Потенциалдуу коркунучтарды белгилөө үчүн, ушул колдонуу боюнча нускаманын Коопсуздук пропорциясын караңыз.

Коопсуздук

Өкүлчүлүктөр жана символдор

Note: Important instructions which involve safety are highlighted with the appropriate mark:

КОРКУНУЧ

Коопсуздук боюнча сунуштар

Тараза жабдууларын коопсуздук талаптары жогорулатылган чөйрөдө колдонууда тиешелүү эрежелерди сактоо керек.

Тараза таразасын берилген кубат адаптери менен гана колдонсо болот.
Электр адаптерин таразага туташтырардан мурун, колдонуучу иштөөчү волtagкубат адаптеринде көрсөтүлгөн дtage. If not, please contact Customer Service at the address above.

If the power adapter or its cable is damaged, the weighing scale must immediately be disconnected from the electricity supply (unplug the power adapter).
If there should be any reason to believe that it is no longer safe to operate the scale, it should be immediately unplugged from the electricity supply (unplug power adapter) and secured against inadvertent operation.

During maintenance work, it is essential to follow the recommendations set out in maintenance and servicing.
Таразаны жарылуу коркунучу бар аймакта иштетүүгө болбойт.

Care must be taken when weighing liquids to ensure that no liquid is spilled inside the scale, into connections on the rear of the equipment, or the power adapter. If liquid is spilled on the scale, it must immediately be unplugged from the main electricity supply (unplug power adapter).
Таразаны тейлөө боюнча адис биринчи жолу текшергенден кийин иштетсе болот.

These operating instructions must be read by each user and should always be easily accessible at the workplace.

Индикатор

The weighing scale consists of certain parts.

Индикатор
Кронштейн орнотуу
Load Cell Wiring
AC адаптер
Пайдалануу боюнча колдонмо
Монтаждоо бурамалар

Өзгөчөлүктөрү

Авто арткы жарык (тандалган)
Auto off (selectable)
Жаныбарларды таразалоо
кармап туруу функциясы
Пик кармап туруу функциясы
Any Cal calibration software
RS232 функциясы
To work either as an indicator, or a display
Three modes: Normal mode / Setting mode /Internal Auto Calibration mode

Zero range: + 10% of full capacity
Нөл диапазону (толук кубаттуулуктун 0дөн 10%ке чейин)
Tare Range (10% to full capacity)
4.5Ah rechargeable battery (REMO-R only)
Display options：5 digital LCD
Error message indication：
- Ашыкча жүктөө
- Unstable when power on
- Calibration code is not enough or operation error
- Батареянын төмөн көрсөткүчү

Interface Data：

1 signal interface：（microphone socket)
- Red——-E+（positive source） / Blue ——- S+（positive signal）
- Black——-E-（negative source） / Green——-S-（negative signal） No sign (yellow) ——- GND
2 recharge battery socket：
- AC/DC 10V――――――external positive, inner negative

RS232 interface：DB9

RS232 TRANSMIT FUNCTION

1. RS232 interface：DB9

RS232 Transmission Agreement：

Режим: Жөнөкөй асинхрондук серия
Baud rate： 9600  Data Bit：8
Parity Bit：NONE
Stop Bit：1
Data Format：ASCII
Transmission Information Format： 20 Byte, blank=20H
Example: 50kg

Колдонмо & Шайкештик

The following are instructions on how to correctly use the indicator:
The indicator may only be used for the weighing of solid materials and of liquids contained in secure containers.

The maximum capacity load of the weighing scale must be correctly entered in the indicators program, otherwise the weighing scale may be damaged.
When using the indicator in combination with other devices including those produced by other manufacturers, the appropriate regulations for the safe use of the relevant attachments and their application in accordance with instructions must be observed.

The indicator has been manufactured and tested in accordance with the standards and recommendations set out in the declaration of conformity.
The power adapter supplied for the indicator complies with the appropriate electrical protection class.

The following applies to all REMO series indicators.

Электр камсыздоо:

Input: 110V AC 50Hz to 60Hz
REMO Output: 9v 400mAh
REMO-R Output: 12v DC 1000mAh
Уруксат берилген айлана-чөйрө шарттары:
Temperature: 32ºF – 104ºF / 5°C. 40°C

Салыштырмалуу нымдуулук:

25% – 85%, конденсацияланбайт
NOTE: If you have any questions on the technical data or require detailed technical information on your balance, please contact your technical representative.

Баштоо

The indicator is packaged in an environmentally friendly carton, which provides optimum protection for the indicator during transportation.

We suggest that you keep the original packaging to avoid damage if you are shipping or transporting the scale to a different location. It is also the best way to keep it in the best condition if it will not be used for an extended period.
To avoid damage, please follow the instructions provided below, when unpacking the scale:
- Unpack the indicator carefully.
- When outside temperatures are very low, the indicator should be stored for a couple hours in its box in a dry room at normal temperature. This prevents any condensation from settling on the unit when opening the box.
- Check the indicator immediately after unpacking for any external visual damage. If there is any damage on the indicator, contact customer service immediately.
- If the indicator is not to be used immediately after purchase, it should be stored in a dry place where fluctuations in temperature are low. (reference pg.18).
- Read through these operating instructions before you work with the unit and pay attention to the safety recommendations.

Жеткирүү

Бардык компоненттерди таңгактан чыгаргандан кийин жеткирүүнүн толуктугун дароо текшериңиз.

Толук жеткирүү үчүн текшерүү тизмеси

Компонент	Учурда Ооба / Жок
Көрсөткүч бирдиги
Кубаттуу адаптер
Пайдалануу боюнча колдонмо
Кронштейн орнотуу
Load cell wiring

Монтаждоо жана орнотуу

The indicator is delivered in a partly dismantled condition. Assemble the individual components in the following sequence:

Mount your machine on a clean, dry surface to ensure optimal visibility of your readings.

AC адаптерин туташтыруу

The following safety recommendations must be observed when connecting the balance:

КОРКУНУЧ

The scale should only be connected to the mains voltage socket with the power adapter supplied. Before connecting the power adapter to the mains socket, check to see that the operating voltage stated on the power adapter complies with the local mains voltage.
Эгерде операциялык томtage негизги том менен бирдей эмесtage, кубат адаптери розеткага туташтырылбашы керек жана кардарларды тейлөө кызматына кайрылыңыз.

Таразаны жайгаштыруу

The location in which the scale is placed is very important for the scale to work to its full potential. Certain conditions can affect the capabilities of the scale, such as presence of air flow, variations in temperature, and direct sunlight. Please follow the recommendations given below when choosing a location to place your scale.
- Place the indicator on a solid, firm and preferably vibration-proof surface.
- Make sure that the indicator cannot be shaken or knocked over.
- Protect from direct solar radiation.
- Avoid drafts and excessive temperature fluctuations.
- Avoid placing the indicator near or on any magnetic surfaces.

Remo Indicator Mounting Drawing

Кабарларды көрсөтүү

The STABLE icon indicates when the readings stabled.
The ZERO icon indicates when the weights tared to zero.
The LO-BAT icon indicates when running out of battery.
The kg – Kilograms (1000 grams) is a unit of measure.
The lb. – Pounds (16 ounces) is unit of measure.

Негизги функциялар

(icon) key turns the indicator on or off.
key is used to hold the weight value.
key sets display to zero or subtracts the container weight.

key changes the weight units, kg, lb.
key is used to send data to an external device through RS232 connection.

Функция орнотуулары

Auto чылбыры

- басып, кармап туруңуз баскычын басып, анан басыңыз key to turn on the scale, the display will show A-ON or A-OFF, press key to select (A-ON means auto power off function activate, A-OFF means auto power off function inactivate). Continue to backlight.

Арткы жарык

баскычын басыңыз, the display will show L-ON, L-OFF, or L-Au, press key to select (L-ON means auto backlight function is active, L-OFF means auto backlight function is inactive, L-Au means backlight under auto mode). Continue to print function.

Басып чыгаруу функциясы

Басыңыз key, the display will show P-XX. Press key to select OFF, key, con, or Stb. (OFF means RS232 function is inactive; Key means that you can output the data by pressing key. Con means that the data outputs continually. Stb means that the data will output when the reading is stable). Continue to power-on mode .

Күйгүзүү режими

Басыңыз key, the display will show J-ON or J-OFF, press key to select (JON means showing zero when turning on the power, J-OFF means showing weight placed when turning on the power.) Continue to weighing function.

Таразалоо функциясы

Басыңыз key, the display will show F-Nor or F-PEA or F-Ani. Press key to select (F-Nor means normal weighting function is activated. F-PEA means peak hold weighing function is activated. F-Ani means animal weighing function is activated). Continue to display mode.

Дисплей режими

Басыңыз key, the display will show N-dsp or N-Ind. Press key to select (Ndsp means it can display synchronously as a separate display for another indicator through the RS232 output. N-Ind means it works only as an indicator for the scale.) Continue to peak hold mode.

Чоку кармап туруу режими

In FUNCTION SETTING 5, please choose F-PEA. F-PEA means peak hold weighing function is active, before weighing, please press key. Continue animal anti shock range.

Animal Anti-Shock Range (F-Ani only)

Басыңыз key, the display will show Kd 50, Kd 100, Kd 200, or Kd 400. Press key to select animal scale anti-shock range among 50, 100, 200, and 400. Continue to filter range.

Filter Range (F-Ani only)

• басыңыз key, the display will show Fd 0.5, Fd 3, Fd 5, Fd 10. Press key to select animal scale filter range among 0.5, 3, 5, or 10. Continue to animal scale filter time.

Animal Scale Filter Time (F-Ani only)

• басыңыз key, the display will show Ft 1 or Ft 2 or Ft 3 or Ft 4. Press key to select animal scale filter time among 1, 2, 3, or 4. Continue to unit select function.

Unit Select Function

Басыңыз key, the display will show U-on or U-off, press key to select U-on or U-off. (U-on means you can switch unit between kg and lb., U-off means lb. unit will be disabled.)

Turn indicator off to save selections.

***NOTE: Kd, Fd, and Ft work in Animal Weighing Mode (F-Ani) only. ***

HOLD функциясы

Place the item on the scale platform. Wait for the stable indicator to be displayed.

басыңыз key. The “ . “ (hold indicator) will turn ON.
Remove the item from the scale platform. The item’s weight reading will remain on the display. Now you can also select Unit (lb. or kg) by pressing key. (lb. cannot be selected if lb. is disabled in Function Setting)

Quit HOLD function:

Once an item is weighed and the hold function is enabled, and you want to quit the HOLD function.

басыңыз key again to cancel the “. “ (hold indicator) and return the scale to weighing mode.

Калибрлөө

Сизге эмне керек:

Using a calibration or test weight that is 2/3 of the max capacity is strongly recommended for recalibration.
If you do not have a test weight or calibration weight. You can use any object of “known weight” to calibrate with our scales AnyCal Calibration software.

NOTE: when calibrating even if you use a “known weight” the more exact the weight is the more precise the calibration will be.

Prepare for calibration by following these steps:

While the indicator is OFF, press and hold key then press key. The display will show CAPU=.
Басыңыз key to select capacity unit kg or lb.(unit lb. cannot be selected if the lb. is disabled in FUNCTION SETTING).

Басыңыз тандоону ырастоо үчүн баскыч.
Басыңыз key again to enter the next menu, the display will show CAP.
Басыңыз key to set capacity, press key to move the flashing digit to right, press key to increase the flashing digit value.
Press key to confirm the selection.
Басыңыз key again to enter the next menu, the display will show CALU=.

Басыңыз key to select calibration unit kg or lb. (unit lb. cannot be selected if the lb. is disabled in Function Settings).
Басыңыз тандоону ырастоо үчүн баскыч.
Басыңызkey again to enter next menu, the display will show CAL.
Басыңыз key to confirm the selection (the calibration weight should be more than 2/3 of full capacity).

Басыңызs key again to enter next menu, the display will show DIV,
Басыңыз key to select division.
Басыңыз тандоону ырастоо үчүн баскыч.
Басыңыз key again to enter next menu, the display will show Adb, press key to select (19.20).
Басыңыз тандоону ырастоо үчүн баскыч.

Start the calibration by following these steps:

Басыңыз key, the display will show CAL, then AD value.

Басыңыз key when the stable indicator lights, the display will show the flashing calibration weight, place the shown weight on the platform.
Басыңыз key when the stable indicator lights, the display will show “—–“, and AD value.
Turn OFF the scale.
Calibration is Complete.
Turn ON the scale, place tested weight to check whether it is correct.

If not, please repeat the above instructions.

If this device has been previously programmed, please see “Start the Calibration” steps above for a simplified procedure.

Тейлөө жана тейлөө

КОРКУНУЧ

For maintenance work, the balance must be disconnected from the power supply (remove power adapter plug from socket). Also, ensure that the balance cannot be connected to the power supply during the work by a third party.
Оңдоо иштерин аткарып жатканда таразага суюктук төгүлбөсүн текшериңиз. Таразага суюктук төгүлүп кетсе, аны тейлөөчү техник текшериши керек.

Regularly maintain the weighing pan and the weighing pan holder by removing any dirt or dust from under the weighing pan and on the weighing scale housing. Use a soft brush or a soft, lint-free cloth moistened with a mild soap solution.
Never use solvents, acids, alkalis, paint thinners, scouring powders, or other aggressive or corrosive chemicals for cleaning; these substances can cause damage to the surfaces of the scale housing.

Транспорт жана сактоо

Your weighing machine is a precision instrument, treat it carefully.

Avoid shaking, severe impacts, and vibration during transportation.
Make sure that there are no marked temperature fluctuations during transportation and that the weighing machine does not become damp (конденсация).
If you would like to take the weighing machine out of service for an extended period, disconnect it from the electricity supply, clean it thoroughly (refer to Maintenance & Service) and store it in a place that meets the following conditions:
- No violent shaking or vibrations
- Минималдуу температуранын өзгөрүшү
- Күндүн түз радиациясы жок
- Минималдуу нымдуулук
The weighing machine should preferably be dispatched and transported in the original packaging to avoid transportation damage.

ЭСКЕРТҮҮЛӨР

When the recharging sign “ ” indicates, please charge the battery for 8 to 10 hours. When the charging is done, the orange light will turn green.
Only use the charger (adapter) supplied with the indicator.
After recharging, if the battery does not last long, replace it with a new battery.

Проблемаларды чечүү

*Ката* *Code*	*Маселе*	*Көйгөйлөрдү чечүү*	*Чечим*
ERR-O/0	Ашыкча жүктөө катасы	Turn scale off, then back on, and try weighing using weight under max capacity to verify the loadcell still functions.	If scale still registers accurate weight refrain from continued over loading. If error continues loadcell may be damaged.
ERR-Z/2	Exceeded zero tracing range when powered on.	Turn scale off and clear weighing platform. Turn scale back on and attempt recalibration.	If the scale was recalibrated successfully then the error is resolved. If error persists, scale may need a linearity calibration or has a damaged loadcell.
ERR-S/5	Scale not stable when powered on.	Make sure scale is stable when powered on. Do not touch, shift, or place anything on the weighing platform until after the артка эсептөө.	If error persists, scale may need recalibration. If error continues after recalibration, then loadcell may be damaged.
ERR-C	Calibration weight was not entered during calibration	Enter calibration weight during calibration process.	If error persists, call support.
ERR-P	Counting set error	Жер sample before entering counting settings.	If error persists, call support.
ERR-L	Calibration weight was not placed during calibration.	Be sure to place weight when recalibrating.	If error persists, call support.
ERR-E	Программалык камсыздоо маселеси	If error persists, call support.	If error persists, call support.
ERR-B/6	Батареянын аздыгы катасы	Attempt to charge battery.	If error persists, battery will need to be replaced. Make sure to not leave scale with rechargeable battery plugged in constantly.
үчүн каалаган ката ошол is жок көрсөтүлгөн on бул тизме or ошол уланууда кийин көйгөйлөрдү чечүү сен болот керек чейин байланыш колдоо.

We are genuinely grateful for your recent purchase. Your decision to choose TREE by LW Measurements means a lot to us.

Your support enables us to continue creating and providing high-quality products and services. We hope you enjoy your new scale and that it brings you as much satisfaction as it brings us to serve customers like you.
We would love to know what you think of our TREE products and your experience with us. If you have a chance, please visit www.lwmeasurements.com жана кайра калтырыңызview.
Thank you for being a part of the LW Measurements family. We look forward to serving you again in the future.

All TREE products are designed in the U.S.

Scan to Contact Us OR
Чалуу:707-542-2185

Көп берилүүчү суроолор

Q: What should I do if liquid is spilled on the scale?

A: If liquid is spilled on the scale, immediately unplug it from the main electricity supply and ensure that no liquid enters the connections on the equipment or power adapter.

Документтер / Ресурстар

TREE REMO-R Universal Indicator [pdf] Колдонуучунун колдонмосу
REMO, REMO-R, REMO-R Universal Indicator, REMO-R, Universal Indicator, Indicator

Шилтемелер

User Manual

TREE REMO-R Universal Indicator

Техникалык шарттар

Introduction

Коопсуздук

Индикатор

Өзгөчөлүктөрү

Колдонмо & Шайкештик

Монтаждоо жана орнотуу

Негизги функциялар

Функция орнотуулары

Тейлөө жана тейлөө

Проблемаларды чечүү

Көп берилүүчү суроолор

Документтер / Ресурстар

Шилтемелер

Комментарий калтырыңыз

Жоопту жокко чыгаруу