1. Киришүү
This manual provides detailed instructions for the safe and effective use of your Godox K-180A 180Ws Photography Studio Flash Strobe Light Kit. Please read this manual thoroughly before operating the equipment and keep it for future reference.
2. Коопсуздук маалыматы
Always observe basic safety precautions when using electrical equipment to reduce the risk of fire, electric shock, or injury.
- Агрегатты жамгырга же нымдуулукка дуушар кылбаңыз.
- Do not disassemble the unit. If repairs are needed, contact qualified service personnel.
- кубаттуулукту камсыз кылыңызtage matches the unit's requirements (AC220/60Hz or 110V/60Hz).
- Балдар жетпеген жерде сактаңыз.
- Unplug the unit from the power source before cleaning or when not in use.
- Avoid prolonged continuous use of the modeling lamp; allow it to cool down for at least 1 minute after 5 minutes of continuous use to prevent overheating.
3. Пакеттин мазмуну
Verify that all items are included in your package (based on Kit 8, the most comprehensive option):
- 1x Godox K-180A Flash Unit
- 1x RT-16 Trigger (Transmitter and Receiver)
- 1x 180cm Light Stand
- 1x FS50X70cm Grid Softbox
- 1x Моделдөө Lamp
- 1x Кубат Сымы
4. Орнотуу нускамалары
4.1. Light Stand Assembly
Unfold the light stand legs and extend the telescopic sections to the desired height. Ensure all locking knobs are securely tightened.
4.2. Flash Unit Preparation
- Mount the K-180A flash unit onto the top stud of the light stand.
- Adjust the mounting bracket to achieve the desired angle and securely tighten it.
- The umbrella input is available for attaching a studio umbrella if desired.
4.3. Softbox Assembly
Assemble the FS50X70cm Grid Softbox according to its specific instructions. Attach it to the universal mount on the flash unit.
4.4. RT-16 Trigger Setup
Insert the 23A 12V battery into the transmitter and 2 AAA batteries into the receiver (AAA batteries for receiver not included). Connect the receiver to the flash unit's sync port.
4.5. Power Connection
Connect the power cord to the flash unit's power socket and then to a suitable AC power outlet. Ensure the power switch is in the OFF position before connecting.
5. Иштөө нускамалары
5.1. Күйгүзүү/өчүрүү
Flip the Power Switch (labeled 'POWER') to turn the flash unit ON or OFF. The Charging LED Indicator will illuminate during charging.
5.2. Модель кылуу Лamp Control
Use the Modeling Light Switch (labeled 'MODEL') to turn the modeling lamp ON or OFF. Pushing it downwards (G position) turns it off, upwards (F position) turns it on. Note: Do not keep the modeling lamp on for too long; it is recommended to cool it down for 1 minute after 5 minutes of continuous use.
5.3. Flash Output Control
Rotate the Flash Output Controller (labeled with '+' and '-') to adjust the flash power. The output is stepless from 1/8 to full power. This allows for precise light requirements in different environments.
5.4. Сыноо баскычы
To test the flash or before taking a picture, push the Test Button (labeled 'TEST'). This can also be used to adjust the brightness when combined with the flash output controller.
5.5. Slave Trigger Mode
The flash unit can be triggered synchronously with one external flash. This mode allows the K-180A to act as an auxiliary lamp, жарык менен көлөкөнүн ар кандай эффекттерин сунуш кылат.
6. Техникалык тейлөө
- Тазалоо: Use a soft, dry cloth to clean the exterior of the flash unit and accessories. Do not use abrasive cleaners or solvents.
- Сактагыч: Store the kit in a cool, dry place, away from direct sunlight and excessive humidity.
- Сактагычты алмаштыруу: If the unit fails to power on, check the fuse. Replace it with a fuse of the same rating (5A).
7. Кыйынчылыктарды
- Жарк этпейт:
- Check if the unit is powered on and connected correctly.
- Ensure the RT-16 trigger transmitter and receiver have fresh batteries and are properly synced.
- Verify the sync cord is securely connected to the flash unit.
- Сақтандыргычты текшериңиз.
- Моделдөө лamp иштебей жатат:
- Ensure the Modeling Light Switch is in the ON position.
- l экендигин текшериңизamp bulb is securely installed and not burnt out.
- Ыңгайсыз жарк чыгаруу:
- Ensure the Flash Output Controller is set correctly.
- Allow sufficient recharging time between flashes.
8. Техникалык шарттар
8.1. Godox K-180A Flash Unit
| Өзгөчөлүк | Спецификация |
|---|---|
| Модел | К-180А |
| Flash Output | 180WS |
| Жетектөөчү номер (m ISO 100) | 45 |
| Түс температурасы | 5600 ± 200K |
| Power Voltage | AC220/60Hz or 100V/60Hz (Optional, check your unit) |
| Flash Power Control | Stepless (1/8-full) |
| Моделдөө Л.amp | 75WS |
| Заряддоо убактысы | 0.5-3сек |
| Flash Triggering Model | Sync cord, Test button, Slave |
| Жаркыроонун узактыгы | 1 / 2000-1 / 800s |
| Фузер | 5A |
| Өлчөм | 17 x 10 x 17.5cm (approx. 7.2 x 4.1 x 5.4in) |
| Салмагы | Approx. 0.59KG (approx. 603g / 21.3oz) |
8.2. 180cm Light Stand
| Өзгөчөлүк | Спецификация |
|---|---|
| Жүк көтөрүү | 2кг |
| Телескопиялык бийиктик | 82-200см |
| Сактагычтын бийиктиги | 68см |
| Түтүк диаметри | Φ1.6/1.9/2.2cm |
| Screw Hole | 1/4" |
| Салмагы | 0.81кг |
| Катталган узундук | 67см |
| Мин узундук | 70cm (2'4") |
| Max Height | 200cm (7') |
| Ideal Max. Working Height | 140-150см |
8.3. FS50X70cm Grid Softbox
| Өзгөчөлүк | Спецификация |
|---|---|
| Өлчөмү | 50 x 70cm / 20" x 27" |
| Тоо | Универсал тоо |
| Салмагы | Болжол менен 0.6 кг |
8.4. RT-16 Wireless Flash Trigger
| Өзгөчөлүк | Спецификация |
|---|---|
| Type | Wireless Flash Trigger |
| Каналдар | 16 канал |
| Transmitter Power Input | 23A 12V battery (included) |
| Receiver Power Input | 2 * AAA batteries (not included) |
| Receiver Plug Size | 3.5мм |
| Adapter Size for Receiver Plug | 3.5 мм жана 6.35 мм |
| Radio Working Frequency | 433 МГц |
| Шайкештирүү ылдамдыгы | 1/200с |
| Outdoor Operation Distance | 30 м чейин (ачык мейкиндик) |
| Indoor Operation Distance | 20 м чейин (ачык мейкиндик) |
| Пакеттин өлчөмү | 21.5 x 7.5 x 3.8 см / 8.5 x 3.0 x 1.5 дюйм |
| Пакет Салмагы | 125 г / 4.4 унция |
9. Колдонуучунун кеңештери
- Сүрөттү колдонуу: This kit is primarily intended for photography, providing controlled lighting for studio setups. Experiment with different flash power settings and softbox positions to achieve desired lighting effects.
- Моделдөө Л.amp Колдонуу: While useful for previewing lighting, remember to give the modeling lamp breaks to prevent overheating and prolong its lifespan.
- Trigger Placement: For optimal wireless triggering, ensure a clear line of sight between the RT-16 transmitter and receiver, especially in indoor environments.
10. Кепилдик жана колдоо
Кепилдик маалыматы, техникалык колдоо же тейлөө боюнча суроолор боюнча сатуучуга же өндүрүүчүгө түздөн-түз кайрылыңыз. Сатып алуунун далили катары сатып алуу дүмүрчөгүңүздү сактап коюңуз.
