1. Киришүү
The Brother HD-390A+ is a high-precision analog multimeter designed for electricians, home maintenance, and general electrical testing. It offers a wide range of measurement capabilities including DC voltage, AC томtage, DC current, resistance, battery testing, transistor hFE, diode, decibel, and continuity checks. This manual provides essential information for safe and effective use of your multimeter.
2. Коопсуздук маалыматы
- Мультиметрди туташтыруудан мурун, анын туура функцияга жана диапазонго коюлганын текшериңиз.
- Көлөмдү өлчөөгө аракет кылбаңызtages or currents exceeding the specified maximum ratings of the device.
- Түз электр чынжырлары менен иштөөдө өтө этият болуңуз. Тескерисинче далилденмейинче, ар дайым чынжырлардын иштеп жатканын эсептеңиз.
- Ар бир колдонуудан мурун сыноо өткөргүчтөрүн кандайдыр бир бузулууларга (мисалы, жарылган изоляция, ачык металл) текшериңиз. Бузулган сымдарды дароо алмаштырыңыз.
- Replace batteries and fuses only with the specified types and ratings to maintain safety and performance.
- Эгерде мультиметр бузулган же туура эмес иштесе, аны иштетпеңиз.
3. Орнотуу
3.1 Батареяны орнотуу
The HD-390A+ multimeter requires two AAA 1.5V batteries and one 9V battery for operation. Batteries are not included with the device.
- Мультиметрдин артындагы батарея бөлүкчөсүн табыңыз.
- Open the battery cover by pulling down and opening as indicated on the cover.
- Insert the two AAA 1.5V batteries and one 9V battery, ensuring correct polarity (+/-) as marked inside the compartment.
- Батареянын капкагын бекем жабыңыз.
Visual reference for battery compartment:
Артка view of the Brother HD-390A+ multimeter, highlighting the battery cover.
3.2 Сыноо өткөргүчтөрүн туташтыруу
- Кара тест өткөргүчтү "COM" (Жалпы) уячасына салыңыз.
- Көпчүлүк өлчөөлөр үчүн (томtage, resistance, low current), insert the red test lead into the 'VmAΩ+' jack.
- For high DC current measurements (up to 10A), insert the red test lead into the '+10A' jack.
Visual reference for test lead connection:
Фронт view of the multimeter with test leads connected to the appropriate jacks.
3.3 Zero Ohm Adjustment
Before measuring resistance, it is crucial to perform a Zero Ohm Adjustment to ensure accuracy.
- Set the rotary switch to any resistance (Ω) range.
- Short the red and black test leads together.
- Turn the 'Ω ADJ' knob (yellow knob) until the pointer reads exactly zero on the resistance scale. This compensates for internal battery voltage вариациялар.
4. Иштөө нускамалары
4.1 Overview Controls
The multimeter features a central rotary switch to select the measurement function and range, an 'Ω ADJ' knob for resistance calibration, and input jacks for test leads.
Фронт view of the Brother HD-390A+ multimeter, illustrating the main controls and display.
4.2 Reading the Analog Scale
The analog display features multiple scales for different measurement types. Always refer to the scale corresponding to the selected function and range on the rotary switch.
4.3 Өлчөө процедуралары
- DC Voltage (DCV):
- Set the rotary switch to the desired DCV range (0.1V, 2.5V, 10V, 50V, 250V, 1000V). Start with the highest range if the voltagе белгисиз.
- Кызыл сынагын чынжырдын оң жагына, кара сынагын терс жагына туташтырыңыз.
- Read the value from the DCV scale.
- AC Voltage (ACV):
- Set the rotary switch to the desired ACV range (10V, 50V, 250V, 1000V). Start with the highest range if the voltagе белгисиз.
- Сыноо өткөргүчтөрүн AC том аркылуу туташтырыңызtage булагы.
- Read the value from the ACV scale.
- Measuring DC Current (DCmA):
- МААНИЛҮҮ: Ensure the circuit is de-energized before connecting the multimeter in series.
- Set the rotary switch to the desired DCmA range (50uA, 2.5mA, 25mA, 250mA). For 10A, use the '+10A' jack and the 10A range.
- Схеманы бузуп, мультиметрди жүк менен катар туташтырыңыз.
- Re-energize the circuit and read the value from the DCmA scale.
- Measuring Resistance (Ω):
- МААНИЛҮҮ: Ensure the circuit is de-energized and the component is isolated before measuring resistance.
- Set the rotary switch to the desired Ω range (X1, X10, X100, X1K, X10K, X100K).
- Short the test leads and perform a Zero Ohm Adjustment using the 'Ω ADJ' knob (see Section 3.3).
- Компонент боюнча сыноо өткөргүчтөрүн туташтырыңыз.
- Read the value from the Ω scale and multiply by the range multiplier.
- Battery Check (BATT):
- Set the rotary switch to the 1.5V or 9V BATT range.
- Connect the red test lead to the positive terminal of the battery and the black test lead to the negative terminal.
- Read the battery condition (GOOD, ?, BAD) from the BATT scale.
- Transistor hFE Check:
- Set the rotary switch to the hFE range.
- Insert the transistor leads into the appropriate NPN or PNP sockets.
- hFE маанисин окуу.
- Diode Check:
- Set the rotary switch to the Diode Check range (via Test Leads).
- Connect the test leads across the diode.
- Observe the reading to determine forward voltage drop or open circuit.
- Decibel (dB) Measurement:
- Set the rotary switch to an ACV range.
- Read the dB value from the dB scale.
- Үзгүлтүксүздүктү текшерүү:
- Set the rotary switch to the Rx1 range.
- If the resistance is less than approximately 200 Ohms, a beeper will sound.
4.4 Видео көрсөтүү
Watch this video for a practical demonstration of the Brother HD-390A+ multimeter's basic functions, including resistance and voltage өлчөөлөр.
Video demonstrating the operation of the Brother HD-390A+ Analog Multimeter.
5. Техникалык тейлөө
5.1 Батареяны алмаштыруу
When the pointer does not zero correctly during resistance measurement, or the battery check indicates low power, it's time to replace the batteries. Follow the steps outlined in Section 3.1, 'Battery Installation'.
5.2 Сактагычты алмаштыруу
If the multimeter fails to measure current or shows an open circuit on a known good circuit, the fuse may be blown. The device is protected by Fuses 0.5A/250V and 10A/250V (for the 10A range). Fuse replacement should ideally be performed by qualified personnel. Always replace with fuses of the exact same type and rating.
5.3 Тазалоо
Мультиметрди сүртүңүз casing with a dry, soft cloth. Do not use abrasive cleaners, solvents, or immerse the device in water.
5.4 Сактоо
Store the multimeter in a cool, dry place, away from direct sunlight, extreme temperatures, and high humidity. Remove batteries if storing for extended periods to prevent leakage and damage.
6. Кыйынчылыктарды
- No Reading/No Pointer Movement:
- Check if the multimeter is turned ON (rotary switch not in OFF position).
- Ensure test leads are correctly inserted and not damaged.
- Verify battery charge; replace if necessary.
- Check for blown fuses, especially for current measurements.
- Ensure the rotary switch is set to the correct function and range.
- Туура эмес окуу:
- Verify the correct range is selected for the measurement.
- Perform Zero Ohm Adjustment for resistance measurements.
- Ensure good, clean contact between test leads and the circuit/component.
- Тышкы электрдик тоскоолдуктарды текшериңиз.
- Buzzer Not Sounding (Continuity):
- Ensure the rotary switch is set to the Rx1 range.
- Confirm that the resistance of the circuit being tested is below approximately 200 Ohms.
7. Техникалык шарттар
The following tables detail the technical specifications of the Brother HD-390A+ Analog Multimeter:
Жалпы мүнөздөмөлөр
- Өлчөмдөрү: 160 мм * 105 мм * 40 мм
- Standard Environmental Conditions: 23°C ± 5°C, humidity <75% RH
- Working Environment Range: 0°C ~ 40°C, humidity <90% RH
- Электр камсыздоо: R03P, AAA, 1.5V x2pcs (for Ω, Buzzer, hFE, Diode testing); 6F22 NEDA1604 9V x 1pc (just for Ω(Rx10k) testing).
- Коргоо: Full protection.
Өлчөө мүнөздөмөлөрү
| Test Functions | Диапазон | Тактык | Эскертүү |
|---|---|---|---|
| DC V | 0-0.1-2.5-10-50-250 V -1000V | ±3% FSD. ±4% FSD. For 1000V | Input Impedance: 20KΩ/V Overload Protection: Max. 1000V AC/DC BUT 0.1V/2.5V/10V 250V Max. |
| AC V | 0-10-50-250В -1000V | ±4% FSD. ±5% FSD. For 1000V Band width: 40 ~ 10K Hz | Input Impedance: 9KΩ/V Overload Protection: Max. 1000V AC/DC But 10V/50V only 250V Max. |
| DC мА | 0-0.05-2.5-25-250 mA, 10A | ±3% FSD. ±4% FSD. For 10A | Drop Voltagд: 250 мВ Overload protected by Fuses 0.5A/250V & 10A/250V at 10A range Max. testing time |
| Test Functions | Диапазон | Тактык | Эскертүү |
|---|---|---|---|
| Ω | X 1: 0.2 ~ 2KΩ Midscale at 20Ω X 10: 2 ~ 20KΩ Midscale at 200Ω X 100: 20 ~ 200KΩ Midscale at 2000Ω X1K: 200 ~ 2MΩ Midscale at 20KΩ X10K: 2K ~ 20MΩ Midscale at 200KΩ X100K: 20K ~ 200MΩ Midscale at 2000KΩ | ±3% of ARC of Scale Length | Protected by the extra Thermal Resettable Fuse <250V AC/DC. Powered by AAA 1.5V x2pcs & block 9V battery x1pc. |
| Сыйымдуулук (uF) | 0.025-0.25-25uF(C2 50uA), 2000uF(C1) | ±3% FSD. Approximate Value | Use the Accessory Kit Use the R x 1K range |
| BATT текшерүү | 0 ~ 1.5V: GOOD ? - BAD 0 ~ 9V: GOOD ? - BAD | ±5% of ARC of Scale Length | Load Current: 270mA for 1.5V 25mA for 9V Overload protected by Fuse & Oxide Varactor <250V (5s). |
| Transistor, LED hFE Check | hFE: 0-1000 via special hFe socket Check | Болжолдуу маани | At Ω X 10 Range |
| Диод текшерүү | via Test Leads | Болжолдуу маани | At Ω X 10 Range |
| Децибел | -22 dB ~ + 62 dB (0dB=1mW at 600Ω) | Болжолдуу маани | ACV диапазондорунда |
| Үзгүлтүксүздүктү текшерүү | •))) At Rx1 range | Beeper sounding <200 Ohm approx. | Protected by the Resettable Fuse & Oxide Varactor <250V (5s). |
8. Колдонуучунун кеңештери
- Always start with a higher range when measuring an unknown value to prevent overloading the meter and ensure safety.
- For resistance measurements, ensure the component is isolated from the circuit to get an accurate reading.
- Keep the test leads organized and free from tangles to avoid damage and ensure quick setup.
- Сатып алууну карап көрөлүasing a spare set of fuses and batteries to minimize downtime during critical tasks.
9. Кепилдик жана колдоо
For warranty information, technical support, or service inquiries, please contact the original seller or manufacturer directly. Please retain your purchase receipt as proof of purchase for any warranty claims.
