1. Киришүү
The ANYCUBIC Water Wash ABS-Like Resin 3.0 is an advanced photopolymer resin designed for LCD 3D printers. It offers a balanced combination of toughness, resilience, high precision, and a low shrinkage rate, making it suitable for a wide range of 3D printing applications. This resin is water-washable, simplifying the post-processing cleanup and reducing the need for harsh chemicals. It also features minimal odor for a more pleasant printing experience.
2. Орнотуу жана даярдоо
Proper preparation is crucial for successful 3D printing with resin. Follow these steps before starting your print:
- Жакшы чайкагыла: Before each use, thoroughly shake the resin bottle for at least 30 seconds to ensure all components are evenly mixed.
- Температура: Ensure your printing environment is within the recommended temperature range of 20-50°C (64-95°F).
- Жеке коргонуу каражаттары (ЖКК): Always wear gloves and a mask to avoid direct skin contact and inhalation of resin fumes. Work in a well-ventilated area.
- Принтердин шайкештиги: This resin is compatible with all LCD/DLP printers that use 405nm UV light curing technology. It is optimized for Anycubic LCD printers.
- Pouring Resin: Carefully pour the desired amount of resin into your printer's resin vat. Do not overfill.
3. Иштөө нускамалары
Once your printer is set up and resin is loaded, you can begin the printing process.
3.1 Басып чыгаруу
- Кесүү программасы: Use your preferred slicing software to prepare your 3D model.
- Экспозиция параметрлери: Refer to the table below for recommended exposure parameters for various Anycubic Photon Mono series printers. Adjust settings as needed for your specific printer and model.
| 3D принтер | Layer Thickness /mm | Normal Exposure Time/s | Light-Off Time/s | Bottom Exposure Time/s | Төмөнкү катмарлар | Anti-Aliasing Level | Z Lift Distance/ mm | Z Lift Speed/ mm/s | Z Retract Speed/ mm/s |
|---|---|---|---|---|---|---|---|---|---|
| Photon Mono M7 | 0.05 | 2.2 | 1 | 35 | 4 | 1 | 8 | 6 | 6 |
| Photon Mono M7 Pro | 0.05 | 2 | 1 | 25 | 4 | 1 | 8 | 6 | 6 |
| Photon Mono M7 Max | 0.05 | 2 | 0.5 | 30 | 5 | 1 | 8 | 6 | 6 |
| Photon Mono M5 | 0.05 | 2.8 | 0.5 | 25 | 6 | 1 | 8 | 6 | 6 |
| Фотон моно M5s | 0.05 | 3 | 0.5 | 25 | 5 | 1 | 8 | 6 | 6 |
| Photon Mono M5s Pro | 0.05 | 3.6 | 1 | 30 | 5 | 1 | 8 | 6 | 6 |
| Фотон моно 4 | 0.05 | 2.8 | 1 | 30 | 5 | 1 | 6 | 4 | 6 |
| Фотон моно 4K | 0.05 | 2 | 0.5 | 40 | 6 | 1 | 8 | 4 | 6 |
| Photon Mono 4 Ultra | 0.05 | 2.6 | 1 | 30 | 5 | 1 | 5 | 8 | 8 |
| Фотон моно 2 | 0.05 | 2.5 | 1 | 28 | 5 | 1 | 6 | 4 | 6 |
| Photon Mono X2 | 0.05 | 2.5 | 0.5 | 25 | 5 | 1 | 8 | 2 | 3 |
| Photon Mono X 6K | 0.05 | 2 | 0.5 | 23 | 6 | 1 | 8 | 2 | 3 |
| Photon Mono X6Ks | 0.05 | 2.5 | 0.5 | 20 | 6 | 1 | 8 | 2 | 3 |
| ANYCUBIC Фотон M3 Max | 0.05 | 3 | 2 | 30 | 6 | 1 | 10 | 4 | 4 |
| ANYCUBIC Photon M3 Premium | 0.05 | 2.5 | 0.5 | 25 | 3 | 1 | 8 | 6 | 6 |
*We recommend setting the first layer exposure duration to 35-40s when printing with HD gray resin.
3.2 Кийинки иштетүү
- Remove Print: Carefully remove the printed model from the build plate.
- Support Removal: Remove any necessary support structures. The resin is designed for easy support removal, even for delicate parts.
- Water Washing: Thanks to hydrophilic agents, the resin is water-washable. Rinse the printed model thoroughly with water to remove residual liquid resin.
- Айыктыруу: After washing, cure the model under UV light according to your printer's recommendations to achieve optimal hardness and strength.
Environmental Note: Avoid direct wastewater disposal into the sewer system to protect groundwater from contamination.
4. Техникалык тейлөө жана сактоо
Proper maintenance and storage will prolong the life of your resin and ensure consistent print quality.
- Сактагыч: Store the resin in a sealed container in a cool, dark place, away from direct sunlight and dust.
- Жарактуулук мөөнөтү: The resin has a shelf life of 1 year.
- Unused Resin: Filter any unused resin from the vat back into its original bottle for future use.
- Тазалоо: Clean your resin vat and build plate thoroughly after each print session.
5. Кыйынчылыктарды
Бул жерде кээ бир жалпы маселелер жана алардын мүмкүн болуучу чечимдери:
- Басып чыгаруудагы ката: Ensure correct exposure settings for your printer model (refer to the table in Section 3.1). Check for proper bed leveling and sufficient support structures.
- Greasy or White Stains on Prints: This resin has a lower water absorption rate to mitigate such issues. Ensure thorough washing with clean water and proper curing.
- Крекинг: The water-washable formula is designed to make cured prints less prone to cracking. Ensure prints are fully cured and not exposed to excessive stress immediately after printing.
- Poor Detail/Accuracy: Verify your printer's calibration and ensure the resin is well-mixed before use.
6. Техникалык шарттар
6.1 Physical Properties
| Менчик | Нарк |
|---|---|
| Материал | Hydrophilic group-modified light-curing resin |
| Толкун узундугу | 365-405нм |
| Илешкектүүлүк | 400-500/mPa.s (25°C) |
| тыгыздыгы | 1.07-1.09/g/cm3 |
6.2 Механикалык касиеттери
| Менчик | Нарк |
|---|---|
| Катуулугу | 83-86HD |
| Тартуу күчү | 36-46МПа |
| Тыныгуудагы узартуу | 35-45% |
| Bending Modulus | 40-50МПа |
| Ийилген күч | 2000-2500МПа |
| Young's Modulus | 1800-2300МПа |
| Izod Impact Strength | 133J / m |
| Volume Shrinkage Rate | 4-5% |
6.3 жеткиликтүү түстөр
| Түс | Hex Color Value | Түстүү дисплей |
|---|---|---|
| Кара | #212721 | |
| Ак | #EFF0F1 | |
| Беж | #FCC89B | |
| Боз | #7E93A7 | |
| HD Gray | #768692 | |
| Таза | / | |
| Translucent Red | #D22630 | |
| Translucent Green | #009A17 | |
| Smoky Black | #688197 |
Эскертүү: Products used in the pictures are real products, still there may be color difference due to light or display. The color of the product received shall prevail.
7. Колдонуучунун кеңештери
- Painting Prints: After your models are fully cured, they can be painted using standard model paints to add further customization and detail.
- Resin Mixing: Always ensure the resin is thoroughly mixed before pouring into the vat, especially if it has been sitting for a while, to prevent pigment separation and ensure consistent print quality.
- Вентиляция: Maintain good ventilation in your printing area to minimize exposure to resin fumes, even with low-odor resins.
- Жоюу: Dispose of cured resin and contaminated water responsibly, following local regulations. Never pour liquid resin or contaminated water directly down the drain.
8. Кепилдик жана колдоо
ANYCUBIC provides support for its products. For any issues or inquiries regarding your ABS-Like Resin 3.0, please refer to the official ANYCUBIC website or contact their customer service for assistance. Keep your purchase receipt as proof of purchase for any warranty claims.
