1. Киришүү
The Acrel ADL400 three-phase electric meter is designed for accurate energy measurement in low voltage systems. This meter complies with the technical requirements for electronic meters as specified in the IEC62053-21 and IEC62053-22 standards, ensuring reliable performance for energy management applications.
2. Коопсуздук маалыматы
WARNING: Installation and maintenance should only be performed by qualified electrical personnel. Ensure all power is disconnected before installation or servicing to prevent electric shock or damage to the equipment.
- Ар дайым жергиликтүү жана улуттук электр эрежелерин сактаңыз.
- Эгер аппарат бузулуп калса, аны иштетпеңиз.
- Аппаратты нымдуулуктан жана экстремалдык температурадан алыс кармаңыз.
3. Продукт бүтүп калдыview
The ADL400 is a compact DIN rail mountable energy meter featuring an LCD display and intuitive button controls for easy operation and parameter viewing.
Сүрөт 3.1: Алдыңкы view of the ADL400 Energy Meter
3.1. Компоненттер жана дисплей
The meter features a 12-bit section LCD display with a backlight for clear readings. Control is managed via three front-panel buttons:
Сүрөт 3.2: Баскыч функциялары
- Жогору баскычы (▲): Used to navigate up through menus, check voltage and current, and move the flashing cursor leftward in programming mode.
- Төмөн баскычы (▼): Used to navigate down through menus, check power, and change the flashing value in programming mode.
- Киргизүү баскычы (↵): Used to enter menus, check energy, access the in/out programming menu, and save changes.
4. Техникалык шарттар
| Категория | Параметр | Нарк |
|---|---|---|
| Өлчөө | Зымдар | 3 фаза 3 зымдар, 3 фаза 4 зымдар |
| Rated Voltage | 3x380~456Vac L-L (direct connect); 3x100~120Vac L-L (via PTs) | |
| Номиналдуу ток | 3x10(80)A AC (direct connect); 3x1(6)A AC (via CTs) | |
| Жыштык | 45~65Гц | |
| Accuracy Class (kWh) | 0.5 | |
| Measuring Energy Range | 0-99999.9кВт/саат | |
| Өлчөө параметрлери | U, I, P, Q, S, PF, F, Harmonics (2~31st) | |
| Тtage Импеданс | >2МΩ | |
| Учурдагы керектөө | <1VA Бир фазалык номиналдык ток | |
| Дисплей түрү | LCD дисплей | 12 Bits Section LCD Display |
| Байланыш | Интерфейс | RS485 |
| Протокол | MODBUS-RTU | |
| Bod Rate | 1200bps~19200bps | |
| Курчап турган чөйрө | Иштөө температурасы | -25℃~+55℃ |
| Салыштырмалуу нымдуулук | ≤95% RH (No condensation) | |
| Физикалык | Өлчөмдөр | 72*90*65мм |
| Орнотуу | Монтаждоо | 35 мм динамометрдик рельс |
| Электр камсыздоо | Type | AC |
| Батарея | камтылган | Ооба |
| Кепилдик | Мезгил | 2 жыл |
5. Орнотуу жана орнотуу
5.1. Physical Installation (DIN Rail)
The ADL400 meter is designed for easy installation on a standard 35mm DIN rail.
- Push off the buckle: Locate and push off the buckle on the back side of the meter.
- DIN темир жолго орнотуу: Position the meter onto the 35mm DIN rail, aligning the slot behind the meter with the rail.
- Buckle up: Secure the meter by buckling up the latch to fix it firmly onto the DIN rail.
- Орнотууну текшерүү: Ensure the meter is securely installed and does not wobble.
Figure 5.1: DIN Rail Installation Steps
5.2. Электр схемасы
Proper wiring is crucial for accurate measurement and safe operation. Refer to the following diagrams based on your connection type.
5.2.1. Terminal Overview
Figure 5.2: PIN/Terminal Overview (Direct Connect Type)
Figure 5.3: PIN/Terminal Overview (CT Operated Type)
5.2.2. Direct Connect Wiring
Figure 5.4: Power Wiring: 3-phase 4-wire via direct connect. Meters must be installed according to the indicated current direction.
Figure 5.5: Power Wiring: 3-phase 3-wire via direct connect. Meters must be installed according to the indicated current direction.
5.2.3. CT Operated Wiring
Figure 5.6: Power Wiring: 3-phase 4-wire CT operated. AC Voltage Input via direct connect & Current Input via -/5A CTs.
Figure 5.7: Power Wiring: 3-phase 3-wire CT operated. AC Voltage Input via direct connect & Current Input via -/5A CTs.
5.2.4. RS485 байланыш зымдары
For remote communication and data acquisition, connect the RS485 interface as shown:
Figure 5.8: RS485 Wired Communication (Direct Connect Type) with IoT Gateway. Recommended cable: RVSP 2x1.5mm².
Figure 5.9: RS485 Wired Communication (CT Operated Type) with IoT Gateway. Recommended cable: RVSP 2x1.5mm².
6. Иштөө нускамалары
6.1. Дисплей Навигация
The ADL400 meter allows users to view various electrical parameters by navigating through the display using the front panel buttons. The video below demonstrates this process.
Video 6.1: ADL400 Product Demonstration and Display Navigation. This video shows the physical product and how to cycle through measurement parameters using the buttons.
6.2. Параметрлерди программалоо
To configure the meter's settings, follow the programming sequence outlined in the diagram below. This includes setting parameters such as PT/CT ratio, wiring methods, and communication settings.
Figure 6.1: Operation Diagram for Parameter Programming
Жалпы программалоо кадамдары:
- Long press the Enter button to enter the programming page.
- Use the Up and Down keys to enter the password.
- Enter the edit page.
- Navigate through parameters (e.g., Addr, bAUd, PAr, H, Lo, Ct, Pt, dir, PL, LED, CodE, CLrE) using the Up/Down keys.
- Set parameters by using the Up/Down keys to change values.
- After setting all parameters, press the Enter key to save.
7. Кыйынчылыктарды
This section addresses common issues you might encounter with your ADL400 meter.
7.1. Inaccurate Power or Energy Count
Көйгөй: After the meter is powered on, the power or energy count is inaccurate.
Чечим:
- Switch the meter display to show power (active power P, power factor λ).
- Check whether the power display is negative or not.
- Verify if the power factor is between 0.9-0.95.
- Check whether the incoming and outgoing wires of the current signal wire are connected reversely. The incoming wire must be the same as the incoming wire end of the instrument and consistent with the wiring diagram on the instrument.
7.2. Communication Failure with Host Computer
Көйгөй: The instrument cannot communicate with the host computer normally after power on.
Чечим:
- Томду текшерүүtage value between the communication output A and B of the measuring instrument. It should be between +4.4-4.5V.
- Check whether the communication wiring method is correctly wired in accordance with the wiring diagram requirements (i.e., the communication terminal A/B of the corresponding to communication serial port A/B).
8. Техникалык тейлөө
- Тазалоо: Эсептегичтин сыртын тазалоо үчүн жумшак, кургак чүпүрөктү колдонуңуз. Абразивдүү тазалоочу каражаттарды же эриткичтерди колдонбоңуз.
- Байланыштары: Мезгил-мезгили менен бардык зымдарды байланыштарды текшерип туруңуз, алар бекем жана коррозиядан таза.
- Курчап турган чөйрө: Ensure the operating environment remains within the specified temperature and humidity ranges to prolong the meter's lifespan.
9. Колдонуучунун кеңештери
The ADL400 is a robust energy meter designed for precise measurement. Here are some tips based on common inquiries:
- Energy Monitoring for EV Chargers/Solar Panels: The ADL400 is a 3-phase energy meter primarily designed for measuring AC power consumption. While it can monitor the energy usage of systems that include solar panels or EV chargers, it does not directly control or manage the charging process for electric vehicles from photovoltaic systems. Its main function is accurate measurement and data collection within the electrical infrastructure.
- Маалыматтарды каттоо: Utilize the RS485 Modbus-RTU communication to connect the meter to a data logger or an IoT gateway for continuous monitoring and historical data analysis.
- Multi-Tariff Functionality: If your model supports multi-tariff, configure the time zones and tariff rates (Spike, Peak, Flat, Valley) to accurately track energy consumption costs based on different periods.
10. Кепилдик жана колдоо
The Acrel ADL400 meter comes with a 2 жылдык кепилдик from the date of purchase. For technical support, service, or warranty claims, please contact your vendor or the manufacturer directly. Ensure you have your product model and purchase details available.
11. Сертификаттар
The ADL400 meter is certified to meet various international standards, ensuring quality and compliance:
- CE: Conforms to European Union safety, health, and environmental protection requirements.
- CE-MID: Complies with the Measuring Instruments Directive (MID) for legal metrology in Europe.
- EAC: Conforms to the technical regulations of the Eurasian Customs Union.
- IEC62053-21: Static meters for active energy (Class 1 and 2).
- IEC62053-22: Static meters for active energy (Class 0,2 S and 0,5 S).
11.1-сүрөт: Мисample CE Certificate
12. Тиркемелер
The ADL400 energy meter is suitable for a wide range of applications requiring precise three-phase energy measurement and management:
Figure 12.1: Diverse Application Areas
It can be integrated into an IoT Energy Management System (EMS) for advanced monitoring and control:
Figure 12.2: IoT EMS Platform Integration. This diagram illustrates how the ADL400 can be part of a comprehensive energy management system, enabling remote monitoring and data analysis.
Specific application examples камтыйт:
- Имараттар: Monitoring energy consumption in commercial and residential buildings.
- Industrial Facilities: Tracking power usage in mining, petrochemical, and manufacturing plants.
- Infrastructure: Energy management in municipal engineering and transportation systems.
- Specialized Facilities: Use in hospitals and hotel apartments for detailed energy accounting.
- Renewable Energy: Monitoring energy flow in solar PV installations.
- EV Charging Stations: Measuring energy consumed by electric vehicle chargers.
Building
Solar PV
EV заряддагыч
