1. Продукт бүтүп калдыview
This 433.92MHz rolling code remote control is designed for compatibility with various garage door openers and gate systems. It features a robust design and multiple buttons for controlling different functions or devices.
Эмне камтылган:
- Алыстан башкаруу бирдиги
- Pre-installed Battery
- Ачкычка тиркеме
- English Manual (this document)
Сүрөт 1: Алдыңкы view 4 баскычтуу алыстан башкаруу пульту.
2. Техникалык шарттар
| Өзгөчөлүк | Деталь |
|---|---|
| Модель номери | 433mhz Rolling Code |
| Коддоо ыкмасы | Жылдыруу коду |
| Иштөө жыштыгы | 433.92 МГц |
| Сертификация | CE |
| Origin | Материк Кытай |
| Пакет узундугу | 13 см |
| Пакет туурасы | 9 см |
| топтом Бийиктиги | 2 см |
| Пакет Салмагы | 0.047 кг |
3. Орнотуу жана программалоо
This remote uses rolling code technology, which requires pairing directly with your receiver unit (garage door opener or gate motor). The exact pairing procedure varies by manufacturer. Please refer to your original receiver's manual for specific instructions. Below is a general guide for common rolling code systems.
Жалпы жупташтыруу процедурасы:
- Locate the 'Learn' or 'Program' Button on Your Receiver: This button is typically found on the motor unit of your garage door opener or gate system. It might be labeled 'Learn', 'Code', 'Program', or have a small LED indicator next to it.
- Окуу режимин иштетүү: Press and release the 'Learn' button on your receiver. The LED indicator on the receiver will usually light up or flash, indicating it is in learning mode. This mode typically lasts for a short period (e.g., 10-30 seconds).
- Жаңы пультту программалоо: While the receiver is in learning mode, press and hold the desired button on your new 433.92MHz remote control (e.g., button 'A' as shown in Figure 1). Keep the button pressed until the receiver's LED indicator changes (e.g., flashes rapidly, turns off, or lights solid), confirming successful pairing.
- Пультту текшерүү: Release the button on the remote. Wait a few seconds, then press the programmed button again to test if it operates your garage door or gate.
- Program Additional Buttons (Optional): If your remote has multiple buttons and you wish to control other devices, repeat steps 2-4 for each additional button and corresponding receiver.
Important: If you encounter difficulties, consult the manual for your specific garage door opener or gate system. Some systems may require a different sequence or have specific timing requirements.
4. Пультту иштетүү
Once successfully programmed, operating your remote control is straightforward:
- Жалгыз басуу: Press the programmed button once to activate the associated device (e.g., open/close garage door, open/close gate).
- Диапазон: Ensure you are within effective operating range of your receiver. Obstructions and environmental factors can affect signal strength.
5. Техникалык тейлөө
Батареяны алмаштыруу:
The remote control uses a standard small coin cell battery (e.g., CR2032). When the remote's range decreases significantly or the LED indicator (if present) fails to light up, it's time to replace the battery.
- Алыстан башкаруу пультун c этияттык менен ачыңызasing using a small screwdriver or a thin prying tool.
- Remove the old battery, noting its polarity (+/-).
- Туура полярдуулукту камсыз кылып, ошол эле типтеги жаңы батареяны салыңыз.
- в жабууasing коопсуз.
Тазалоо:
Пультту жумшак, кургак чүпүрөк менен сүртүңүз. Абразивдүү тазалоочу каражаттарды колдонбоңуз же пультту сууга салбаңыз.
6. Кыйынчылыктарды
- Программалоодон кийин пульт иштебей жатат:
- Ensure the receiver was in learning mode during programming.
- Пульттун батареясын текшериңиз.
- Verify that your receiver is compatible with 433.92MHz rolling code remotes.
- Repeat the programming steps carefully, paying attention to timing.
- Кыска иштөө диапазону:
- Пульттун батареясын алмаштырыңыз.
- Пульт менен кабыл алгычтын ортосунда эч кандай чоң тоскоолдуктар жок экенин текшериңиз.
- Check for sources of interference (e.g., other wireless devices, metal structures).
- Remote LED does not light up:
- Батарея түгөнүп калган же туура эмес орнотулган болушу мүмкүн. Батареяны алмаштырыңыз.
- Ensure the remote is not damaged.
7. Колдонуучунун кеңештери
- Keep Original Remote Handy: Always keep your original remote control as a backup, especially during programming.
- Clear All Codes (If Needed): If you are having trouble programming, some receivers allow you to clear all existing remote codes before programming new ones. Consult your receiver's manual for this option.
- Суунун таасиринен сактаныңыз: While durable, the remote is not waterproof. Avoid exposing it to excessive moisture.
- Коопсуз сактагыч: Store the remote in a safe place to prevent accidental button presses or loss.
8. Кепилдик жана колдоо
This product is covered by a standard manufacturer's warranty against defects in materials and workmanship. For specific warranty details or technical support, please contact the seller or refer to the product listing where you made your purchase. Keep your proof of purchase for warranty claims.
