SAMP-200 HIFI эки ядролуу TPA3255 стерео Ampкөтөргүч такта

1. Киришүү

SAMP-200 is a high-performance Class D power amplifier board designed for true high-end sound quality. It features an advanced integrated feedback design and proprietary high-speed gate driver error correction (PurePath Ultra HD) to maintain ultra-low distortion across the entire audio frequency band. This amplifier board operates in AD mode, offering significant power output and high efficiency with ultra-low idle losses.

2. Негизги өзгөчөлүктөрү

• Utilizes two American TI-TPA3255 power amplifier modules for superior output power separation.
• Front-end differential input circuit with boost technology for enhanced dynamic range.
• Fully shielded, low-loss sealed inductors and imported filter capacitors ensure stable performance.
• Operates in AD mode with Class D efficiency.
• Unique 2 VRMS analog input interface for seamless connection with high-performance DACs (e.g., TI's PCM5242).
• High power efficiency with ultra-low power level idle losses (less than 2.5W).

3. Техникалык шарттар

Note: The power test results are measured at a 50V power supply. Using a lower voltage power supply (e.g., 24V or 36V) will result in reduced output power.

4. Пакеттин мазмуну

• 1 х SAMP-200 Digital Power Ampкөтөргүч такта

5. Орнотуу нускамалары

Careful connection is essential for proper operation and to prevent damage to the amplifier board and connected equipment. Ensure all connections are secure before applying power.

5.1 Электр булагы

Connect a DC power supply within the range of 19V to 52V to the designated power input terminals on the board. Observe correct polarity (positive and negative). The terminals are typically labeled 'DC 19V-50V' or similar.

5.2 Аудио киргизүү туташуусу

Connect your audio source (e.g., DAC, preamplifier) to the 2 VRMS analog input interface. The input terminals are typically labeled 'INPUT L', 'G' (Ground), and 'R'. Use appropriate shielded audio cables to minimize noise.

5.3 Динамиктин чыгышын туташтыруу

Connect your passive speakers to the output terminals. Ensure correct polarity for each channel (Left+ L-, Right+ R-). The board supports speaker impedances of 2, 4, or 8 ohms. Verify your speakers' impedance matches the ampкөтөргүчтүн мүмкүнчүлүктөрү.

6. Иштөө нускамалары

Once all connections are made, you can begin operating the ampкөтөргүч такта:

1. Күйгүзүү: Connect the power supply to a wall outlet. The amplifier board should power on, indicated by any onboard LEDs (if present).
2. Аудио ойнотуу: Туташкан булагыңыздан аудио ойнотууну баштаңыз.
3. Үндү көзөмөлдөө: Adjust the volume using your audio source or any external preamplifier connected to the input. This amplifier board does not have onboard volume control.
4. Өчүрүү: Disconnect the power supply from the wall outlet to power off the ampкуткаруучу такта.

7. Техникалык тейлөө

Сиздин узак жана оптималдуу иштешин камсыз кылуу үчүн ampкөтөргүч тактасын тейлөө боюнча төмөнкү көрсөтмөлөрдү аткарыңыз:

• Тазалыкты сактоо: Regularly clean the board with a soft, dry cloth. Avoid using liquids or abrasive cleaners.
• Нымдуулуктан качыңыз: сактаңыз amplifier board away from water, humidity, and other liquids.
• Статикалык разряддын алдын алуу: Handle the board with care, especially when installing or removing, to avoid electrostatic discharge (ESD) which can damage components.
• Вентиляцияны камсыз кылуу: The heatsink is crucial for dissipating heat. Ensure it is not obstructed and that there is adequate airflow around the board, especially during prolonged operation at high power.
• Сактагыч: When not in use for extended periods, store the board in a dry, dust-free environment.

8. Кыйынчылыктарды

Эгер сиз S. менен көйгөйлөргө туш болсоңузAMP-200 ampкөтөргүч такта, төмөнкү жалпы көйгөйлөрдү жана чечимдерди караңыз:

8.1 Үн чыгышы жок

• Күчтү текшерүү: Ensure the power supply is correctly connected and providing the specified voltage (19V-52V DC).
• Аудио киргизүүнү текшерүү: Verify that the audio source is connected correctly to the input terminals and is playing audio.
• Check Speaker Connections: Ensure speakers are properly connected to the output terminals with correct polarity.
• Үн деңгээли: Confirm that the volume on your audio source or preampкөтөргүч минималдуу деңгээлге коюлган эмес же үнсүз режимде өчүрүлгөн эмес.

8.2 Бурмаланган үн

• Киргизүү деңгээли: Reduce the input signal level from your audio source. An excessively high input signal can cause distortion.
• Электр камсыздоо: Ensure the power supply is stable and can provide sufficient current for the desired output level. Fluctuations or insufficient current can lead to distortion.
• Динамик Импеданс: Verify that your speakers' impedance is compatible with the amplifier (2, 4, or 8 ohms).

8.3 Low Output Power

• Power Supply Voltage: As noted in the specifications, lower input voltage will result in reduced output power. Ensure your power supply is providing adequate voltage, ideally closer to the upper limit (52V) for maximum output.
• Динамик Импеданс: Lower impedance speakers (e.g., 2 ohms) will draw more current and allow for higher power output compared to higher impedance speakers (e.g., 8 ohms) at the same voltage.

9. Колдонуучунун кеңештери

• Кубат менен камсыздоону тандоо: For optimal performance and to achieve the advertised maximum output power, it is highly recommended to use a robust power supply capable of delivering up to 52V DC with sufficient current capacity (e.g., 20A or more). This will allow the amplifier to operate at its full potential.
• Жылуулук башкаруу: While the board includes a heatsink, consider additional cooling solutions (e.g., a small fan) if operating at very high power levels for extended periods, especially if enclosed in a case.

10. Кепилдик жана колдоо

For any technical assistance, warranty claims, or support inquiries, please contact the seller or retailer from whom you purchased this product. Please provide your purchase details and a clear description of the issue to facilitate prompt support.