1. Киришүү
The SUNLU RC01 Plus UV Curing Box is a dedicated device for post-curing 3D printed resin models. It utilizes a 405nm UV lamp and a 360° rotating turntable to ensure complete and even curing, enhancing the hardness and durability of your prints. This manual provides essential information for the safe and effective use of your curing box.
2. Пакеттин мазмуну
Чогултуудан мурун, бардык компоненттердин бар экендигин жана бузулбагандыгын текшериңиз:
- Acrylic Board x 6
- Кубат адаптери x 1
- Таймер x 1
- Rubber Fixing Ring x 1 Bag
3. Орнотуу жана чогултуу
The SUNLU RC01 Plus UV Curing Box is designed for easy assembly. Follow these steps:
- Connect UV Light Power Cord: Identify the UV light bar and its power cord. Connect it to the designated power cord hole.
- Install Sections and Fix Buckles: Assemble the acrylic boards by slotting them together. Use the provided rubber fixing rings to secure each section.
- Install Door and Turntable Link Cable: Attach the door panel and connect the turntable link cable to ensure proper rotation.
For a visual guide, please refer to the assembly video below:
4. Иштөө нускамалары
Once assembled, the curing box is ready for use:
- Place Model: Open the front door and place your 3D printed resin model on the 360° rotating turntable inside the box.
- Туташуу кубаты: Connect the power adapter to the curing box and plug it into a suitable power outlet.
- Set Curing Time: Use the smart timer controller to set the desired curing duration. The timer allows for settings from 1 second to 600 seconds (10 minutes).
- Start Curing: Press the 'Start Timer' button on the controller. The UV lights will activate, and the turntable will begin to rotate.
- Коопсуздук өзгөчөлүгү: The curing box includes a door sensor. If the door is opened during operation, the UV lights will automatically turn off to prevent direct exposure to UV rays.
- Аяктоо: Once the set time elapses, the UV lights will turn off, and the turntable will stop. You can then remove your cured model.
5. Техникалык тейлөө
- Тазалоо: Regularly wipe the interior and exterior surfaces of the curing box with a soft, dry cloth. Avoid using abrasive cleaners or solvents that could damage the acrylic.
- УВ Лamp: UV LED lamps are designed for long-term use. If you notice a significant decrease in curing efficiency over time, inspect the LEDs for any visible damage or dust accumulation.
- Сактагыч: When not in use, store the curing box in a cool, dry place away from direct sunlight and excessive dust.
6. Кыйынчылыктарды
- UV Lights Not Turning On:
- Ensure the power adapter is securely connected to both the curing box and the power outlet.
- Check if the timer is set and the 'Start Timer' button has been pressed.
- Verify the door is fully closed, as the built-in sensor will prevent operation if open.
- Айланбай турган таблица:
- Check the turntable link cable connection.
- Ensure no obstructions are preventing the turntable from moving freely.
- Тегиз эмес айыктыруу:
- Ensure the model is centered on the turntable.
- Increase the curing time if models are consistently tacky or soft in certain areas.
- Verify that all UV LEDs are functioning correctly.
7. Техникалык шарттар
| Өзгөчөлүк | Спецификация |
|---|---|
| Продукт аты | Light Curing Oven |
| Модель номери | DIY Kit RC01 PLUS |
| Бренд аты | СУНЛУ |
| Таза Салмак | 1.2 кг |
| Продукциянын өлчөмдөрү | 235 x 225 x 230 мм |
| Maximum Curing Capacity | 170 x 205 x 155 мм |
| Түс | Ак |
| UV толкун узундугу | 405 нм |
| LED Lamps | 6 high-power 405nm UV LED lamps |
| Таймерди орнотуу диапазону | 1ден 600 секундага чейин |
| Turntable Rotation Speed | Approximately 10 revolutions per minute |
| Киргизүү спецификациялары | AC 100V~240V, 50/60Hz |
| Output Specifications | DC: 12V ± 1.2V, 1A |
| Максималдуу жумушчу күчү | 12 Вт |
| Колдонуу үчүн айлана-чөйрөнүн температурасы | 0℃~40℃ (Best use: 20℃~35℃) |
| Салыштырмалуу нымдуулук | ≤90% |
| Шайкештик | LCD, DLP, SLA 3D printed items (405nm resins) |
8. Колдонуучунун кеңештери
- Pre-Wash Models: Always thoroughly wash your resin prints with isopropyl alcohol (IPA) to remove uncured resin before placing them in the curing box. This prevents a sticky surface.
- Optimal Curing Time: The ideal curing time can vary based on the resin type, model size, and ambient temperature. Start with shorter times (e.g., 60-120 seconds) and gradually increase if needed. Over-curing can sometimes lead to brittleness or discoloration.
- Биринчи коопсуздук: Although the box has a safety sensor, avoid looking directly at the UV lights when they are active.
- Вентиляция: Ensure good ventilation in your workspace, especially when handling resin and during the curing process.
9. Кепилдик жана колдоо
SUNLU provides a 12 MONTHS warranty for all its products. If you encounter any defects or issues with your SUNLU RC01 Plus UV Curing Box, please contact SUNLU customer service. Provide a detailed description of the problem and any relevant photos or videos to assist in troubleshooting. Our professional after-sale team is available to help resolve your concerns.
