1. Киришүү
This manual provides detailed instructions for the installation, operation, and maintenance of your Szaoju Wireless RF Relay Module and Remote Control Switch. Please read this manual thoroughly before use to ensure proper functionality and safety.
2. Техникалык шарттар
2.1. Кабыл алуучу модулу
| Өзгөчөлүк | Нарк |
|---|---|
| Working Voltage | DC 6V-30V |
| Иштөө температурасы | -40°Cден +80°Cге чейин |
| Receiver Sensitivity | >97дБм |
| Иштөө жыштыгы | 433 МГц |
| Output Voltage Терминалдар | NO (Normal Open), NC (Normal Close), COM (Common) |
| Max жүктөө тогу | 10A |
| Өлчөмдөр | 35мм x 30мм x 15мм |
2.2. Алыстан башкаргыч
| Өзгөчөлүк | Нарк |
|---|---|
| Buttons | 1 Button (Round Button Kit) |
| Working Voltage | 2x CR2016 batteries (not included) |
| Иштөө жыштыгы | 433 МГц |
| Remote Distance | 20-50 метр |
| Иштөө агымы | 13 мАч |
| Код түрү | Fixed code / EV1527 code |
2.3. Пакет маалыматы
- Таңгактын узундугу: 17 см
- Пакеттин туурасы: 17 см
- Таңгактын бийиктиги: 3 см
- Пакет Салмагы: 0.171 кг
2.4. Сертификаттар
- CE Certified
- RoHS ылайыктуу
- Келип чыгышы: Материк Кытай
CE and RoHS certification logos.
3. Орнотуу жана зымдар
Before connecting, ensure all power is off. The receiver module operates on DC 6V-30V. The remote control requires 2x CR2016 batteries (not included).
3.1. Receiver Module Overview
Image showing the receiver module with its components: antenna, learning button, and indicator light. The module measures 35x31.5x17mm and weighs 25.4g.
The receiver module features terminals for power input (V-, V+) and relay output (NO, COM, NC). There is also a learning button and an LED indicator for pairing and status.
Diagram illustrating the terminal definitions on the receiver: V- (negative electrode), V+ (positive electrode), NO (Normal Open), COM (Common terminal), NC (Normal Close).
3.2. Электр схемасы
Below are common wiring configurations for the relay module. Always ensure correct polarity and voltage matching for your application.
3.2.1. Load Wiring Diagram (e.g., LED Lamp)
This diagram shows how to connect a DC power source (5V-60V) to the V+ and V- terminals of the receiver. An LED light is connected between the COM and NO (Normally Open) terminals. The learning button and LED indicator are also shown.
3.2.2. Door Lock Switch Wiring Diagram
This diagram illustrates connecting a DC power source (5V-60V) to the V+ and V- terminals. A door lock is connected between the COM and NC (Normally Closed) terminals. The learning button and LED indicator are also present.
3.2.3. External Power Supply Wiring Diagram
This diagram shows how to connect an external DC power supply to the V+ and V- terminals, and a light connected to the COM and NO terminals. This setup allows the light to be powered by a separate source from the module's control voltage.
3.2.4. Smart Garage Door Opener Integration
This diagram illustrates the relay module as a companion device for an existing wired garage door opener. The module's relay output connects to the wall button/console input of the garage door motor unit, allowing remote control. The module is powered by DC 5V-30V.
4. Иштөө нускамалары
The relay module supports four working modes: Momentary, Toggle, Latching, and Delay. The remote control can be placed anywhere, offering flexibility without wiring.
The round button remote control can be easily placed on various surfaces like glass or walls using double-sided tape, or simply held in hand, providing stable signal transmission.
4.1. Learning and Clearing Method
Watch the video below for a visual guide on learning and clearing codes.
Video demonstrating the pairing process for different modes (Momentary, Toggle, Latched, Delay) and how to clear the remote control code from the receiver.
4.1.1. Learning a Remote Control
- Input DC 6V-30V power to the receiver module.
- Press the learning button on the receiver. The receiver's LED indicator will turn ON.
- Press button A on your remote control once. The LED indicator will flash once.
- Then, press button B on your remote control once. The LED indicator will flash once again. This indicates successful learning.
The specific number of presses on the receiver's learning button determines the operating mode:
- Убактылуу режим: Press the learning key of the receiver once.
- Toggle Mode (Self-locking): Press the learning key of the receiver twice.
- Latched Mode (Interlock): Press the learning key of the receiver three times.
- Кечиктирүү функциясы: Press the learning key of the receiver four or more times for different delay durations. Each additional press adds 5 seconds to the delay.
- 4 presses: 5-second delay
- 5 presses: 10-second delay
- 6 presses: 15-second delay
- 7 presses: 20-second delay
4.1.2. Clearing Remote Control Codes
To clear all remote control data from the receiver's memory:
- Keep pressing the learning key of the receiver 8 times.
- The receiver's LED indicator will flash, indicating that the clearing process is successful. All previously paired remotes will be unpaired.
4.2. Operating Modes Explained
- Убактылуу режим: Press and hold the remote control button (e.g., A), the corresponding relay on the receiver turns ON. Release the button, the relay turns OFF.
- Toggle Mode (Self-locking): Press the remote control button (e.g., A) once, the corresponding relay on the receiver turns ON. Press the same button again, the relay turns OFF.
- Latched Mode (Interlock): Press remote control button A, the corresponding relay on the receiver turns ON. Press remote control button B, the relay on the receiver turns OFF. (Requires a remote with at least two distinct buttons).
- Delay Mode (Timed): Press the remote control button (e.g., A) to turn on the corresponding relay. Press the same button again, and the relay will turn off after a pre-set delay (5s, 10s, 15s, or 20s, depending on the learning setup).
5. Техникалык тейлөө
- Тазалоо: Use a dry, soft cloth to clean the receiver and remote control. Do not use liquids or abrasive cleaners.
- Батареяны алмаштыруу (Алыстан башкаруу): The remote control is powered by 2x CR2016 batteries. When the remote's range decreases or it becomes unresponsive, replace the batteries. Ensure correct polarity.
- Экологиялык шарттар: Avoid exposing the devices to extreme temperatures, high humidity, or direct sunlight.
- Интерференция: Keep the devices away from strong electromagnetic fields to prevent interference.
6. Кыйынчылыктарды
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Remote not controlling receiver | Not paired, out of range, low remote battery, interference. | Re-pair the remote (Section 4.1.1). Check remote battery. Ensure devices are within 20-50m range. Reduce interference sources. |
| Ресивердин LED жарыгы күйбөй жатат | No power, incorrect wiring. | Check power supply (DC 6V-30V) and wiring connections (V+, V-). |
| Реле которулбай жатат | Incorrect wiring, faulty relay, incorrect operating mode. | Verify load wiring (NO, COM, NC terminals). Check if the correct operating mode is set (Momentary, Toggle, Latched, Delay). |
| Алыскы аралык начар | Low remote battery, environmental obstacles, interference. | Replace remote batteries. Ensure clear line of sight. Minimize interference from other RF devices. |
7. Колдонуучунун кеңештери
- For applications requiring precise timing, utilize the delay mode and test the delay duration thoroughly before final deployment.
- When using the remote for garage doors, consider the "Momentary" mode for a quick open/close action, mimicking a traditional push button.
- Ensure the remote control batteries are fresh for optimal range and reliability.
- The compact size of the receiver allows for discreet installation in various projects.
8. Көп берилүүчү суроолор (FAQ)
- С: Максималдуу том деген эмнеtage the receiver can handle?
- A: The receiver module can handle a working voltagDC 6V 30V диапазону.
- С: Батареялар алыстан башкаруу куралына кошулганбы?
- A: No, for shipment safety, 2x CR2016 batteries are not included and must be purchased separately.
- С: Мен бир ресивер менен бир нече пультту колдоно аламбы?
- A: Yes, the receiver can be paired with multiple remote controls. Follow the learning procedure for each remote.
- С: Мен кантип иштөө режимин өзгөртүүгө болот?
- A: The operating mode is set during the learning process by pressing the receiver's learning button a specific number of times (1 for Momentary, 2 for Toggle, 3 for Latched, 4+ for Delay). To change the mode, you must first clear the existing code and then re-pair the remote in the desired mode.
9. Кепилдик жана колдоо
This product is covered by the standard manufacturer's warranty. For technical support, warranty claims, or further assistance, please contact the seller or refer to the product listing for contact information. Keep your purchase receipt as proof of purchase.
