1. Киришүү
This manual provides instructions for the setup, operation, and maintenance of your BFT Mitto series garage door remote control. These remotes are designed for use with compatible BFT receivers, operating on a 433.92MHz frequency with rolling code technology. Please read these instructions carefully before attempting to program or use your new remote control.
2. Шайкеш моделдер
Your new remote control is compatible with the following BFT models:
- MITTO 2 / MITTO 4
- MITTO2M / MITTO4M
- MITTO B RCB 02
- MITTO B RCB 04
- KLEIO B RCA 02
- KLEIO B RCA 04
- TRC1 / TRC2 / TRC4
Маанилүү эскертүү: Access to your receiver/opener is required for programming. Please ensure you have physical access to the receiver before purchasing or attempting to program the remote.
3. Өзгөчөлүктөрү
- Алыстан башкаруу: Ideal for replacing lost or damaged original BFT remote controls.
- Оңой жупташтыруу: Designed for straightforward programming with your existing BFT receiver.
- Rolling Code Technology: Provides enhanced security for your garage door or gate.
- Узак аралык: Operates effectively within a range of 30m-50m in open areas.
- Алдын ала орнотулган Батарея: Comes with a battery included for immediate use after programming.
4. Техникалык шарттар
| Өзгөчөлүк | Деталь |
|---|---|
| Бренд | BFT |
| Программалоонун түрү | Programming with the receiver |
| Жыштык | 433.92 МГц |
| Коддоо ыкмасы | Rolling Code |
| Buttons | 2 же 4 |
| Диапазон | 30м-50м (ачык аянтча) |
| Батарея | камтылган |
| Сертификация | CE |
| Origin | Материк Кытай |
5. Орнотуу жана программалоо
To program your new BFT remote control, you will need to access the receiver unit of your garage door opener or gate system. The programming process involves interacting with buttons on the receiver board.
Программалоо кадамдары:
- Кабыл алуучуну табыңыз: Open the motor housing of your garage door or gate system to access the receiver board. Refer to Figure 7 for a typical receiver layout.
- Initiate Programming Mode: Press either the SW1 or SW2 button on the receiver board until the LED light on the receiver starts to flash.
- Pair Remote Buttons (First Line): Simultaneously press buttons 1 and 2 on your new remote control. Keep them pressed until the LED light on the receiver turns ON solid (stops flashing). Release the buttons.
- Pair Additional Buttons: Press button 1 on your new remote control until the LED on the receiver starts flashing again. Repeat this step for any other buttons you wish to program on the remote. Each button on the remote can be programmed to control a different function or door.
If you encounter difficulties, please refer to the "Troubleshooting" section or contact customer support.
6. Операция
Once programmed, operating your BFT remote control is simple:
- Ачылышы/жабылышы: Press the programmed button on your remote control to activate your garage door or gate opener.
- Токтотуу: Press the same button again while the door/gate is in motion to stop it.
- Артка кайтаруу: Depending on your opener's settings, pressing the button again after stopping may reverse the direction of travel.
7. Техникалык тейлөө
Батареяны алмаштыруу:
Your remote control comes with a pre-installed battery. When the remote's range decreases significantly or the LED indicator on the remote no longer lights up when a button is pressed, it's likely time to replace the battery. The remote uses a standard 12V battery (e.g., 23A or A23 type).
- Алыстан башкаруу пультун c этияттык менен ачыңызasing.
- Эски батареяны алып салыңыз.
- Туура полярдуулукту (+/-) камсыз кылып, жаңы 12V батареяны салыңыз.
- Алыстан башкаруу пультун c жабыңызasing коопсуз.
8. Кыйынчылыктарды
- Программалоодон кийин пульт иштебей жатат:
- Ensure you followed all programming steps correctly.
- Check if the receiver's LED lit up solid during programming.
- Verify that your remote model is indeed compatible with your receiver.
- Пульттун батареясын текшериңиз.
- Кыскартылган иштөө диапазону:
- Пульттун батареясын алмаштырыңыз.
- Ensure there are no new obstructions (e.g., metal objects, large vehicles) between the remote and the receiver.
- Check for sources of radio interference in the area.
- Receiver LED does not flash when SW1/SW2 is pressed:
- Ensure the receiver has power.
- Consult your receiver's specific manual for troubleshooting its programming mode.
9. Колдонуучунун кеңештери
- If you are having trouble with programming, search for a video tutorial specific to your BFT receiver model. Many users find visual guides helpful.
- Always keep a spare remote or ensure you have access to your receiver's programming buttons in case your primary remote is lost or damaged.
10. Көп берилүүчү суроолор
- Q: Can I program this remote without accessing my receiver?
- A: No, programming requires physical access to the receiver unit to press its programming buttons (SW1 or SW2).
- Q: Is there a programming video available?
- A: Yes, a programming video is embedded in the "Setup and Programming" section of this manual. If you need further assistance, please contact customer support.
11. Кепилдик жана колдоо
For any issues not covered in this manual, or for further assistance, please contact the seller or manufacturer's customer support. Keep your purchase records for warranty purposes.
A user manual in PDF format is also available for download: View Колдонуучунун колдонмосу (PDF)
