ES 332 Pro Laser No-Contact Photo Tachometer

Продукт бүттүview

The ES 332 Pro Laser No-Contact Photo Tachometer is a premium instrument designed for precise RPM detection. It utilizes a focused Class II laser beam to measure rotational speeds from a distance, enhancing safety during operation. This device features an ergonomic design, a continuous backlit 5-digit LCD display for clear visibility, and memory functions to capture maximum, minimum, and last readings.

Негизги өзгөчөлүктөрү:

• Focused, high-intensity Class II Laser beam for RPM readings up to 6 feet away.
• Ergonomic shape with continuous backlit LCD display.
• Memory functions for maximum, minimum, and last readings.
• Accuracy rating of +/- 0.05 percent +1 digit.
• Sampling rate of 2 readings per second.
• Wide RPM range: 0 to 99,999 RPM.

Image: The ES 332 Pro Laser No-Contact Photo Tachometer, shown with its protective carrying case and included reflective strips.

Кутуда эмне бар

Пакетти ачканда, сиз төмөнкү буюмдарды табышыңыз керек:

• 1 x ELECTRONIC SPECIALTIES - Pro Laser Photo Tachometer (Model 332)
• 1 х Коргоочу баштык
• 1 x Battery (pre-installed, with protective tab)
• 3 x Reflective Strips
• 1 x Instruction Manual

Жайгашуу

Before using your tachometer, ensure it is properly prepared for operation.

Батареяны орнотуу/иштетүү:

1. Аппараттын артындагы батарея бөлүкчөсүн табыңыз.
2. If a protective plastic tab is present, gently pull it out to activate the pre-installed battery.
3. If replacing the battery, twist the battery cover counter-clockwise to open. Insert a new CR2450 lithium battery with the positive (+) side facing up. Close the cover by twisting clockwise until secure.

Applying Reflective Tape:

For accurate non-contact measurements, a reflective target must be applied to the rotating object.

1. Ensure the surface where the tape will be applied is clean, dry, and free of oil or grease.
2. Cut a small piece (approximately 1/2 inch by 1/2 inch) of the provided reflective tape.
3. Carefully peel off the backing of the tape.
4. Firmly press the reflective tape onto the rotating part (e.g., shaft, pulley, fan blade). Ensure it is flat and smooth.

Иштөө нускамалары

Follow these steps to take accurate RPM measurements with your tachometer.

Өлчөө жүргүзүү:

1. Ensure the reflective tape is securely attached to the rotating object.
2. Hold the tachometer firmly, pointing the laser beam directly at the reflective tape on the rotating object. Maintain a distance of 2 to 6 feet for optimal performance.
3. басып, кармап туруңуз СЫНОО button. The laser will activate, and the display will show the current RPM reading.
4. бошотуңуз СЫНОО button to stop the measurement. The last measured RPM will remain on the display.

Эстутум функциялары:

The tachometer stores the maximum, minimum, and last readings.

• Өлчөө жүргүзгөндөн кийин, баскычын басыңыз MEM button to cycle through the stored values: Maximum RPM, Minimum RPM, and Last RPM.
• Эстутумду тазалоо үчүн басып, кармап туруңуз MEM button for approximately 3 seconds until the display resets.

Бирдик режимдери:

The tachometer may offer different measurement units or display modes. Refer to the detailed manual for specific instructions on how to switch between modes using the available buttons (e.g., 'M' or 'S' buttons if present on your model).

Техникалык тейлөө

Proper maintenance ensures the longevity and accuracy of your tachometer.

Тазалоо:

• Аппаратты жумшак, кургак чүпүрөк менен сүртүңүз. Абразивдүү тазалагычтарды же эриткичтерди колдонбоңуз.
• Keep the laser aperture and display clean for optimal performance.

Батареяны алмаштыруу:

Replace the battery when the low battery indicator appears on the display or if the device fails to power on.

1. Twist the battery cover on the back of the unit counter-clockwise to open.
2. Эски CR2450 батареясын алып салыңыз.
3. Insert a new CR2450 lithium battery with the positive (+) side facing up.
4. Батареянын капкагын ордуна коюңуз жана аны бекитүү үчүн саат жебеси боюнча буруңуз.

Сактагыч:

When not in use for extended periods, store the tachometer in its protective carrying case in a cool, dry place, away from direct sunlight and extreme temperatures.

Проблемаларды чечүү

If you encounter issues with your ES 332 Tachometer, refer to the following common problems and solutions:

• Дисплей жок/Түзмөк күйбөйт:
  Check the battery. Ensure the protective tab is removed and the battery is correctly installed. Replace the battery if necessary.
• Inaccurate or Erratic Readings:
  Ensure the reflective tape is clean, flat, and securely attached. Verify the laser beam is pointed directly at the reflective tape. Adjust the distance between the tachometer and the target (optimal 2-6 feet). Ensure there are no obstructions or excessive ambient light interfering with the laser.
• Laser Not Activating:
  камсыз кылуу СЫНОО button is pressed and held. Check battery status.
• Дисплей тоңуп калат:
  Түзмөктү баштапкы абалга келтирүү үчүн батарейканы алып чыгып, кайра салып көрүңүз.

Бул чечимдерди колдонууга аракет кылгандан кийин көйгөйлөр чечилбесе, кардарларды колдоо кызматына кайрылыңыз.

Техникалык шарттар

Медиа

Продукциянын демонстрациялык видеосу

Кепилдик жана колдоо

For warranty information, technical support, or service inquiries, please refer to the contact details provided in your product packaging or visit the official Electronic Specialties webсайт. Сатып алуу квитанциясын кепилдик дооматтары үчүн сатып алуунун далили катары сактаңыз.