Introduction
This manual provides essential information for the safe and effective installation, operation, and maintenance of the Emerson 767A-372 Hot Surface Ignitor. Please read this manual thoroughly before attempting any installation or service.
Маанилүү коопсуздук маалыматы
WARNING: Risk of electric shock and fire. Installation and servicing must be performed by a qualified service technician.
- Always disconnect power to the appliance before installing or servicing the ignitor.
- Do not touch the ignitor element with bare hands. Oils from skin can damage the silicon carbide material and shorten its lifespan.
- Handle the ignitor with extreme care. The silicon carbide element is fragile and can break easily if dropped or mishandled.
- Ensure all wiring connections are secure and correct according to the appliance manufacturer's specifications.
- Verify the ignitor voltage (120V) matches the appliance requirements.
Продукт бүттүview
The Emerson 767A-372 is a 120V hot surface ignitor designed for reliable ignition in various heating appliances. It features a durable silicon carbide element and a Molex side lock connection for secure wiring.
This image displays the Emerson 767A-372 Hot Surface Ignitor. It features a light-colored ceramic base, two dark grey silicon carbide heating elements, and white insulated wires leading to a white Molex side lock connector.
Негизги өзгөчөлүктөрү:
- Silicon carbide construction for high reliability.
- 5.25" lead length for flexible installation.
- 200 Degree insulation for heat resistance.
- Molex side lock connection with .092" male pins for secure electrical contact.
- 120V операциялык томtage.
Орнотуу нускамалары
Follow these steps carefully to install the ignitor. Refer to your appliance's service manual for specific instructions and diagrams.
- Электр энергиясын өчүрүү: Turn off all electrical power to the heating appliance at the main service panel. Confirm power is off using a voltage метр.
- Access Ignitor: Locate and carefully open the access panel to the burner assembly where the ignitor is situated.
- Эски от алдыргычты алып салуу: Disconnect the wiring harness from the old ignitor. Carefully unmount the old ignitor from its bracket. Note its orientation for correct replacement.
- Монтаждоону текшерүү: Inspect the mounting bracket for any damage or corrosion. Clean if necessary.
- Жаңы от алдыргычты орнотуу: Gently mount the new Emerson 767A-372 ignitor onto the bracket, ensuring it is securely fastened and correctly positioned. Avoid touching the silicon carbide element.
- Зымдарды туташтыруу: Connect the Molex side lock connector of the new ignitor to the appliance's wiring harness. Ensure a firm connection.
- Коопсуз кирүү панели: Close and secure the access panel to the burner assembly.
- Күчтү калыбына келтирүү: Restore electrical power to the heating appliance.
- Сыноо операциясы: Initiate a heating cycle to verify proper operation of the ignitor and the appliance. Observe for proper ignition.
Операция
The Emerson 767A-372 Hot Surface Ignitor operates automatically as part of your heating appliance's ignition sequence. When a call for heat is initiated:
- The control board sends power to the ignitor.
- The silicon carbide element heats rapidly to a high temperature, becoming incandescent.
- Once the ignitor reaches the appropriate temperature, the gas valve opens, allowing gas to flow.
- The hot surface ignitor ignites the gas.
- After successful ignition, the ignitor typically de-energizes, and the flame sensor confirms the presence of a flame.
No user intervention is required for the ignitor's operation once correctly installed.
Техникалык тейлөө
Regular maintenance of your heating appliance is crucial for its longevity and efficiency. While the ignitor itself requires minimal direct maintenance, periodic inspection is recommended.
- Жылдык текшерүү: During your annual furnace or boiler service, have a qualified technician inspect the ignitor for signs of wear, cracks, or discoloration.
- Тазалоо: Do not attempt to clean the ignitor element with abrasive materials or chemicals. If dust or debris accumulates, a gentle brush or compressed air (with power disconnected) may be used, but extreme care must be taken not to touch or damage the element.
- Алмаштыруу: Ignitors have a finite lifespan. If the ignitor shows signs of degradation or fails to ignite consistently, it should be replaced by a qualified technician.
Проблемаларды чечүү
If your heating appliance is not igniting, the ignitor may be a potential cause. Always consult a qualified technician for diagnosis and repair.
| Симптом | Мүмкүн себеп | Акция |
|---|---|---|
| Ignitor does not glow. | No power to ignitor, faulty ignitor, or control board issue. | Verify power supply. Check wiring connections. Test ignitor for continuity (by a qualified technician). Inspect control board. |
| От алдыргыч күйөт, бирок газ күйбөйт. | Insufficient glow temperature, gas supply issue, or faulty gas valve. | Check gas supply. Inspect ignitor for cracks or damage. Consult technician to test gas valve and ignitor temperature. |
| Ignitor glows, gas ignites, but then extinguishes. | Faulty flame sensor, dirty burner, or flue blockage. | Clean or replace flame sensor. Inspect burner and flue for obstructions. |
| Ignitor element is visibly cracked or broken. | Physical damage or end of lifespan. | От алдыргычты алмаштырыңыз. |
Note: Always ensure power is disconnected before inspecting any internal components.
Техникалык шарттар
| Өзгөчөлүк | Деталь |
|---|---|
| Модель номери | 767A-372 |
| Бренд | Emerson (White-Rodgers) |
| Тtage | 120 вольт |
| Материал | Silicon Carbide (Element), Metal (Housing) |
| Коргошун узундугу | 5.25 дюйм |
| Изоляция | 200 градус |
| Туташтыргыч түрү | Molex Side Lock with .092" male pins |
| Продукциянын өлчөмдөрү (L x W x Y) | 3 x 3 x 6 дюйм |
| Элемент Салмагы | 2.89 унция |
| UPC | 786710508288 |
Кепилдик маалымат
This Emerson 767A-372 Hot Surface Ignitor comes with a 1 жылдык кепилдик from the date of purchase. This warranty covers defects in materials and workmanship under normal use and service. It does not cover damage resulting from improper installation, misuse, abuse, accident, or unauthorized repairs. For warranty claims, please retain your proof of purchase and contact Emerson customer support.
Кардарларды колдоо
For technical assistance, replacement parts, or warranty inquiries, please contact Emerson customer support. You may also visit the official Emerson webкошумча ресурстар жана байланыш маалыматы үчүн сайт.
Webсайт: www.emerson.com
Note: Specific contact details may vary by region. Refer to the packaging or official webакыркы колдоо маалымат үчүн сайт.
