Продукт бүттүview
The Monarch 1110-01 One-Line 6 Character Labeler is a handheld device designed for efficient and accurate price marking. It allows for printing a single line of up to six characters, suitable for pricing, dating, or coding various items. This manual provides detailed instructions for setup, operation, maintenance, and troubleshooting to ensure optimal performance and longevity of your labeler.
Figure 1: The Monarch 1110-01 One-Line 6 Character Labeler, a compact handheld device for price marking.
Жайгашуу
1. Энбелгилер жүктөлүүдө
- Open the label compartment door, typically located on the side or bottom of the labeler.
- Insert the roll of labels onto the spindle, ensuring the labels feed from the bottom of the roll.
- Thread the first few labels through the feed mechanism, following any arrows or guides inside the compartment. Ensure the adhesive side of the label faces away from the print head.
- Pull the labels until they extend slightly past the print opening.
- Этикетка бөлүмүнүн эшигин бекем жабыңыз.
2. Сыя роликти орнотуу/алмаштыруу
The labeler uses a small ink roller for printing. If it's new, or if the print becomes faint, the ink roller may need to be installed or replaced.
- Locate the ink roller compartment, usually near the print head. This may require opening a small latch or cover.
- If replacing, carefully remove the old ink roller. It may snap out or slide off a pin.
- Unpack the new ink roller. Avoid touching the inked surface.
- Insert the new ink roller into its designated slot, ensuring it clicks into place or sits firmly on its pins.
- Close the compartment cover, if applicable.
Иштөө нускамалары
1. Каармандарды орнотуу
The Monarch 1110-01 allows for setting up to six characters on a single line.
- Locate the character adjustment dials on the side of the labeler. There will be one dial for each character position.
- Rotate each dial to select the desired character (numbers, currency symbols, or other available characters) for each position. Ensure the characters align correctly in the display window.
- Verify the selected characters are visible and correctly aligned before printing.
2. Этикеткаларды басып чыгаруу
- Hold the labeler firmly by the handle.
- Position the print head flat against the surface where the label is to be applied.
- Squeeze the trigger handle completely. This action will print the characters and dispense a single label.
- Release the trigger handle to prepare for the next label.
- For best results, apply firm, even pressure when squeezing the trigger and ensure the labeler is perpendicular to the surface.
Техникалык тейлөө
1. Тазалоо
- Сырткы: Wipe the exterior of the labeler with a soft, damp кездеме. Абразивдүү тазалагычтардан же эриткичтерден качыңыз.
- Print Head/Character Bands: Periodically inspect the character bands and print head for ink buildup or debris. Use a soft brush or a cotton swab lightly dampened with rubbing alcohol to gently clean these areas. Ensure the labeler is dry before use.
2. Сактоо
Store the labeler in a cool, dry place away from direct sunlight and extreme temperatures. Ensure no labels are jammed in the mechanism before storing.
Проблемаларды чечүү
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Faint or Incomplete Print | Ink roller is dry or worn out. Debris on print head/character bands. | Replace the ink roller. Clean the print head and character bands as described in the Maintenance section. |
| Энбелгилер тамактанбайт | Labels are jammed. Label roll is empty or incorrectly loaded. | Open the label compartment and clear any jammed labels. Ensure the label roll is correctly loaded and not empty. |
| Characters Misaligned or Unclear | Character dials not set correctly. Debris on character bands. | Re-adjust the character dials to ensure proper alignment. Clean the character bands. |
| Labeler Jams Frequently | Incorrect label size or type. Worn internal components. | Ensure you are using labels specifically designed for the Monarch 1110-01. If the problem persists, contact customer support. |
Техникалык шарттар
| Өзгөчөлүк | Деталь |
|---|---|
| Модель номери | 1110-01 |
| Бренд | Эвери Деннисон |
| Басма сызыктар | One-Line |
| Ар бир саптагы символдор | 6 белги |
| Продукциянын өлчөмдөрү | 7.4 x 9 x 2.3 дюйм |
| Элемент Салмагы | 0.01 унция |
| Басма технологиясы | Термикалык |
| Сыя түсү | Кара |
| Башкаруу ыкмасы | тийүү |
| Controller Type | Push Button |
| Максималдуу медиа өлчөмү | 0.85 дюйм |
| Басма маалымат каражаттары | Энбелгилер |
Кепилдик жана колдоо
Кепилдик маалымат
The Monarch 1110-01 Labeler comes with a чектелген кепилдик from Avery Dennison. Please refer to the warranty card included with your purchase or visit the official Avery Dennison webкамтуу мөөнөтү жана шарттары боюнча белгилүү бир шарттар жана эрежелер үчүн сайтты караңыз.
Кардарларды колдоо
For technical assistance, replacement parts, or further inquiries regarding your Monarch 1110-01 Labeler, please contact Avery Dennison customer support. Contact information can typically be found on the manufacturer's official webсайтында же продуктунун таңгагында.
