Introduction
This manual provides comprehensive instructions for the installation, operation, and maintenance of your Pyramid PB2518 3,000-Watt 2-Channel Bridgeable Mosfet Amplifier. Please read this manual thoroughly before installation and operation to ensure proper use and to maximize the performance of your ampөмүрлүү.
1-сүрөт: Жогорку view of the Pyramid PB2518 ampкөтөргүч, көрсөтүүчүasing its heatsink design and branding.
Коопсуздук маалыматы
Жараат же зыянга учурабаш үчүн ар дайым төмөнкү коопсуздук чараларын сактаңыз ampкөтөргүч жана ага туташкан компоненттер:
- Ensure the vehicle's battery is disconnected before making any power connections to the ampөмүрлүү.
- орнотуу amplifier in a dry, well-ventilated location away from direct sunlight or heat sources.
- Орнотуу бөлүмүндө көрсөтүлгөндөй, кубат, жерге жана динамик туташтыруу үчүн тийиштүү ченегич зымдарын колдонуңуз.
- иштетпеңиз amplifier if it has been exposed to moisture or shows signs of damage.
- Бардык тейлөөлөрдү квалификациялуу кызматкерлерге тапшырыңыз.
Продукт өзгөчөлүктөрү
Пирамида PB2518 amplifier incorporates several advanced features for optimal audio performance:
- Эки каналдуу amplification with soft turn on/off circuitry.
- Remote turn-on capability for integration with head units.
- Power and Protection LED indicators for operational status.
- Maximum output of 1500 Watts per channel (2 channels) or 3000 Watts when bridged into 4 Ohms.
- 2 Ohm stereo stable operation.
- Heavy-duty aluminum alloy heatsink for efficient heat dissipation.
- Signal-to-Noise Ratio (S/N): >95dB.
- Жыштык жообу: 15Hz-30KHz.
- Fully adjustable electronic crossovers (High Pass and Low Pass).
- Mosfet Pulse Width Modulation (PWM) power supplies.
- High and Low level inputs for versatile connectivity.
- Total Harmonic Distortion (THD): <0.04%.
- Variable Bass Boost (0-12dB at 50Hz).
- Variable Gain Control.
- High-level Molex input.
- Fully protected circuitry against overload, short circuit, and thermal issues.
Орнотуу жана орнотуу
Туура орнотуу сиздин оптималдуу иштешиңиз жана узак мөөнөттүү иштешиңиз үчүн абдан маанилүү ampкөтөргүч. Бул кадамдарды кылдаттык менен аткарыңыз.
1. Монтаждоо орду
Choose a mounting location that is dry, well-ventilated, and secure. Ensure adequate airflow around the amplifier's heatsink. Avoid mounting in direct sunlight or near heat-generating components.
2. Электр байланыштары
Before making any connections, disconnect the vehicle's negative battery terminal. Connect the power, ground, and remote turn-on wires as follows:
- +12V (кубат): Connect a fused power cable directly from the positive (+) terminal of the vehicle's battery to the +12V terminal on the amplifier. The fuse should be located within 18 inches of the battery.
- GND (жер): Connect a ground cable of the same gauge as the power cable to a clean, unpainted metal surface of the vehicle's chassis. Ensure a solid electrical connection.
- REM (Алыстан күйгүзүү): Башкы бирдигиңиздин алыскы чыгышынан алыстан күйгүзүүчү зымды телефондогу REM терминалына туташтырыңыз ampкөтөргүч. Бул зым сигнал берет ampбаш бирдиги менен күйгүзүү жана өчүрүү үчүн көтөргүч.
2-сүрөт: Арткы view of the Pyramid PB2518 amplifier, highlighting the power (GND, REM, +12V) and speaker output terminals.
3. Аудио киргизүү байланыштары
The PB2518 supports both High-Level and Low-Level (RCA) inputs.
- Төмөн деңгээл киргизүү (RCA): For head units with RCA pre-outs, connect RCA cables from the head unit's audio output to the "INPUT" RCA jacks on the ampөмүрлүү.
- High-Level Input (Molex): If your head unit does not have RCA outputs, use the supplied high-level input adapter. Connect the speaker wires from your head unit to the adapter, then plug the adapter into the "HIGH LEVEL" input on the ampөмүрлүү.
4. Speaker Connections
Connect your speakers to the "SPEAKER" terminals on the amplifier. Observe correct polarity (+ to + and - to -). The amplifier is 2 Ohm stereo stable and can be bridged for mono operation.
- Стерео режими: Connect one speaker to the Right (+) and Right (-) terminals, and another speaker to the Left (+) and Left (-) terminals.
- Bridged Mode (Mono): To bridge the amplifier for a single channel (e.g., a subwoofer), connect the speaker's positive (+) terminal to the Right (+) terminal and the speaker's negative (-) terminal to the Left (-) terminal. Ensure the speaker impedance is 4 Ohms or higher when bridged. The amplifier can deliver up to 3000 Watts in bridged mode.
3-сүрөт: Арткы view of the Pyramid PB2518 amplifier, illustrating the RCA inputs, high-level input, and various control knobs (Bass Boost, Crossover Mode, Gain).
иштетүү Ampөмүрлүү
орнотулгандан кийин, тууралоо ampоптималдуу аудио аткаруу үчүн көтөргүч орнотуулары.
1. Gain Control (Input Level)
The "INPUT LEVEL" (Gain) control matches the amplifier's input sensitivity to the output level of your head unit. Start with the gain set to minimum (MIN). Gradually increase the gain until you achieve a clear, undistorted sound at your desired volume level from the head unit. Avoid setting the gain too high, as this can introduce distortion and potentially damage speakers.
2. Кроссовер орнотуулары
The PB2518 features fully adjustable electronic crossovers to direct specific frequency ranges to your speakers or subwoofers.
- Crossover Mode Switch: Select between "FULL LP" (Full Range / Low Pass) or "HP" (High Pass).
- ТОЛУК: Passes the full audio frequency range to the speakers. Use this for full-range speakers or if your head unit handles crossovers.
- LP (Low Pass): Allows only frequencies below the set point to pass. Ideal for subwoofers. Adjust the "LOW PASS" knob to set the cutoff frequency (e.g., 50Hz-250Hz).
- HP (High Pass): Allows only frequencies above the set point to pass. Ideal for full-range speakers or component speakers to prevent low frequencies from distorting them. Adjust the "HIGH PASS" knob to set the cutoff frequency (e.g., 120Hz-3KHz).
3. Bass Boost
The "BASS BOOST" control allows you to enhance low frequencies (around 50Hz) from 0dB to +12dB. Use this feature sparingly and adjust carefully to avoid distortion or damage to your speakers, especially subwoofers.
4. Power and Protection LEDs
- POWER (жашыл LED): болгондо жарык берет ampкөтөргүч кубат алып, кадимкидей иштеп жатат.
- PROTECT (Кызыл LED): болгондо жарык берет amplifier detects a fault condition (e.g., short circuit, overheating, low voltage). If this LED lights up, immediately turn off your audio system and troubleshoot the issue.
Техникалык тейлөө
Пирамида PB2518 ampКөтөргүч минималдуу тейлөөнү талап кылат. Анын узак мөөнөттүү иштешин камсыз кылуу үчүн төмөнкү көрсөтмөлөрдү аткарыңыз:
- сактаңыз ampкөтөргүч таза жана чаңдан жана таштандыдан таза. Тазалоо үчүн жумшак, кургак чүпүрөктү колдонуңуз.
- Ensure adequate ventilation around the heatsink. Do not block the cooling fins.
- Мезгил-мезгили менен бардык зымдарды байланыштарды текшерип туруңуз, алар бекем жана коррозиядан таза.
- ачыкка чыгарбагыла ampэкстремалдык температурага же нымдуулукка көтөргүч.
Проблемаларды чечүү
Эгер сиз менен көйгөйлөр пайда болсо amplifier, төмөнкү жалпы көйгөйлөрдү жана чечимдерди карагыла:
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Кубат жок (Күч LED өчүк) | Сактагыч күйүп кеткен; электр/жерге туташуу бошоп калган; алыстан күйгүзүү сигналы жок. | Текшерүү amplifier fuse and inline battery fuse. Verify +12V, GND, and REM connections are secure and receiving proper voltage. |
| Коргоочу LED күйүк (кызыл) | Speaker short circuit; amplifier overheating; impedance too low; DC offset. | Check speaker wiring for shorts. Ensure adequate ventilation. Verify speaker impedance is within amplifier's limits. Allow ampмуздатуу үчүн көтөргүч. |
| Үн чыгышы жок | No input signal; gain set too low; speaker wires disconnected; incorrect crossover setting. | Check RCA/high-level input connections. Increase gain. Verify speaker connections. Adjust crossover settings. |
| Distorted Sound | Gain set too high; poor ground connection; damaged speakers; incorrect crossover. | Reduce gain. Ensure solid ground connection. Inspect speakers for damage. Adjust crossover settings. |
| Кыймылдаткычтын үнү/күңүрт үнү | Poor grounding; RCA cables routed near power cables; faulty head unit. | Improve ground connection. Reroute RCA cables away from power cables. Consider a ground loop isolator. |
Техникалык шарттар
Technical specifications for the Pyramid PB2518 ampөмүр берүүчү:
| Өзгөчөлүк | Спецификация |
|---|---|
| Модель номери | PB2518 |
| Каналдар | 2 |
| Max Power Output (Stereo) | 2 х 1500 Ватт |
| Max Power Output (Bridged) | 1 x 3000 Watts (into 4 Ohms) |
| Минималдуу Импеданс | 2 Ом стерео туруктуу |
| Frequency Response | 15Гц - 30КГц |
| Сигнал-ызы-чуу катышы (S/N) | >95дБ |
| Жалпы гармоникалык бурмалоо (THD) | <0.04% |
| Киргизүү көлөмүtage | 12 вольт (ток) |
| Өлчөмдөрү (L x W x Y) | 13.75 x 12.5 x 4 дюйм (34.93 x 31.75 x 10.16 см) |
| Салмагы | 3.7 килограмм (болжол менен 8.16 фунт) |
Кепилдик жана колдоо
Пирамида PB2518 amplifier comes with a limited one-year warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. It does not cover damage resulting from improper installation, accident, misuse, abuse, neglect, or unauthorized modification.
For warranty service or technical support, please contact Pyramid customer service. Keep your proof of purchase for warranty claims.
For further assistance, visit the official Pyramid website or contact their support channels. Refer to your product packaging or the Pyramid webакыркы байланыш маалыматы үчүн сайт.
