1. Киришүү
The Futaba R2106GF is a super small and lightweight 2.4GHz 6-Channel Micro Receiver designed for remote control applications. It offers a High Speed mode for use with digital servos and includes a fail-safe function on all channels. This receiver is compatible with Futaba FHSS and S-FHSS transmitters and supports a wide voltage range of 4.8V to 7.4V. It is not compatible with FASST systems.
Негизги өзгөчөлүктөрү:
- 6-channel micro receiver.
- 2.4GHz FHSS/S-FHSS compatible.
- High Speed mode for digital servos.
- Fail-safe on all channels.
- Жогорку тtage capability (4.8V - 7.4V).
- Компакт жана жеңил дизайн.
Сүрөт 1.1: Жогорку view of the Futaba R2106GF 6-Channel S-FHSS Micro Receiver, showing channel labels 1-6 and the Futaba logo.
2. Коопсуздук маалыматы
Өзүңүзгө же башкаларга жаракат келтирбөө жана жабдууларыңызга зыян келтирбөө үчүн ар дайым төмөнкү коопсуздук чараларын сактаңыз.
- Ensure the receiver is securely mounted in your model to prevent vibration damage.
- Verify correct polarity when connecting the battery to avoid damage to the receiver.
- Do not operate your model in areas with high radio interference or near power lines.
- Always perform a range check before each flight or operation session.
- Keep the antenna free from obstructions and away from conductive materials.
- Бул продукт 15 жаштан жогорку курактагы колдонуучулар үчүн сунушталат.
3. Пакеттин мазмуну
The Futaba R2106GF package typically includes:
- Futaba R2106GF 6-Channel S-FHSS Micro Receiver
- Instruction sheet (if included separately)
4. Техникалык шарттар
| Өзгөчөлүк | Спецификация |
|---|---|
| Модель номери | R2106GF (FUTL7605) |
| Каналдар | 6 |
| Модуляция | FHSS / S-FHSS |
| Тtage Киргизүү | 4.8В - 7.4В |
| Өлчөмдөрү (L x W x Y) | 38 x 21 x 10 мм (1.50 x 0.85 x 0.40 дюйм) |
| Салмагы | 4 г (0.14 унция) |
| Антеннанын узундугу | 0.5 дюйм (болжол менен 12.7 мм) |
| Шайкештик | Futaba FHSS/S-FHSS transmitters (Not compatible with FASST systems) |
Сүрөт 1.2: Side view of the Futaba R2106GF receiver, showing the six channel ports and the antenna connection.
5. Орнотуу
5.1. Кабылдагычты орнотуу
- Mount the receiver in your model using double-sided foam tape or a similar vibration-dampening material. Ensure it is protected from fuel, water, and excessive vibration.
- Position the antenna to ensure optimal signal reception. Avoid bending or cutting the antenna wire.
- Ensure the antenna is not in contact with carbon fiber or other conductive materials, which can shield the signal.
5.2. Binding (Linking) the Receiver to Your Transmitter
The binding process establishes a unique link between your R2106GF receiver and your Futaba FHSS/S-FHSS transmitter. This must be done before first use.
- Turn on your Futaba FHSS/S-FHSS transmitter and place it in "Link" or "Binding" mode according to your transmitter's manual.
- Connect a battery (4.8V-7.4V) to the R2106GF receiver. The LED on the receiver will begin to flash.
- Press and hold the "SW" (Switch) button on the receiver for approximately 2 seconds. The LED will change its flashing pattern.
- Once the binding process is complete, the LED on the receiver will turn solid green, indicating a successful link.
- Turn off both the receiver and the transmitter. Then, turn them back on (transmitter first, then receiver) to confirm the link is maintained.
Эскертүү: If the LED does not turn solid green, repeat the binding process. Ensure your transmitter is set to FHSS or S-FHSS mode, not FASST.
5.3. Servo Connections
Connect your servos and other components (e.g., ESC, battery) to the corresponding channels on the receiver. The R2106GF has 6 channels, typically labeled 1 through 6 or B/6.
- 1-канал: Aileron (or Steering for surface models)
- 2-канал: Elevator (or Throttle for surface models)
- 3-канал: Throttle (or Auxiliary for surface models)
- 4-канал: Руль
- 5-канал: Gear / Auxiliary
- Channel 6 (B/6): Auxiliary / Battery (often used for battery connection or an additional servo)
Always refer to your model's specific instructions for correct servo assignments.
6. Операция
6.1. Күйгүзүү жана өчүрүү
- Always turn on your transmitter first.
- Then, connect the battery to the receiver or turn on the receiver's power switch.
- To power off, disconnect the receiver battery or turn off the receiver's power switch first.
- Finally, turn off your transmitter.
Following this sequence prevents unintended model operation.
6.2. High Speed Mode
The R2106GF supports a High Speed mode, which is beneficial for digital servos to achieve faster response times. To activate High Speed mode, your transmitter must also support and be set to High Speed (HS) mode. Consult your transmitter's manual for instructions on enabling this feature.
Маанилүү: High Speed mode should only be used with digital servos. Using analog servos in High Speed mode can cause damage to the servos.
6.3. Fail-Safe Function
The R2106GF features a fail-safe function on all channels. In the event of signal loss or low battery voltage from the receiver, the fail-safe system will move the servos to a pre-programmed position (e.g., throttle to idle, control surfaces to neutral) to minimize damage or loss of the model. Refer to your transmitter's manual for setting up fail-safe positions.
7. Техникалык тейлөө
- Ресиверди чаңдан, кирден жана нымдан таза жана таза кармаңыз.
- Ресиверди экстремалдык температурага же түз күн нуруна узак убакытка калтыруудан сактаңыз.
- Regularly inspect all wiring and connections for signs of wear or damage.
- Ensure the antenna is not kinked or damaged.
- Ресиверди колдонбогондо кургак, салкын жерде сактаңыз.
8. Кыйынчылыктарды
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Receiver LED flashes, but no control. | Not bound to transmitter, or transmitter is off. | Ensure transmitter is on. Perform binding procedure (Section 5.2). |
| Receiver LED does not light up. | No power, or incorrect polarity. | Батарея байланышын жана томду текшериңизtage. Verify correct polarity. |
| Erratic servo movement or short range. | Interference, damaged antenna, or low receiver battery. | Check antenna placement. Ensure receiver battery is fully charged. Avoid areas with known interference. |
| Servos not responding in High Speed mode. | Analog servos used with High Speed mode. | Only use digital servos with High Speed mode. Switch transmitter to normal mode if using analog servos. |
9. Кепилдик жана колдоо
9.1. Кепилдик маалыматы
The Futaba R2106GF Micro Receiver comes with a бир жылдык кепилдик from the date of purchase. This warranty covers manufacturing defects and workmanship under normal use. It does not cover damage caused by misuse, modification, accident, or improper installation.
Кепилдик дооматтары үчүн сатып алганыңыздын далилин сактап коюңуз.
9.2. Кардарларды колдоо кызматы
For technical assistance, troubleshooting beyond this manual, or warranty service, please contact Futaba customer support or your authorized Futaba dealer. Refer to the official Futaba webакыркы байланыш маалыматы үчүн сайт.
Онлайн ресурстар: For additional information and compatibility lists, you may visit the official Futaba webсайт: www.futabarc.com
