GPI M-150 сериясындагы күйүүчү май өткөрүүчү насостун колдонуу боюнча колдонмосу

Introduction

The GPI M-150 Series Fuel Transfer Pump is a high-efficiency gear technology pump designed for reliable fuel transfer in various applications. Manufactured in the USA with globally sourced components, it features a rugged diecast aluminum housing and a rotary gear design for minimal maintenance and extended pump life. This pump is compatible with gasoline, E15 ethanol blends, diesel fuel blends (up to B20), and kerosene.

Designed for mobile applications, the M-150 pump is ideal for transferring fuel from truck or trailer-mounted tanks powered by a 12V DC battery. Its robust construction ensures dependable performance even in harsh weather conditions, with operation possible at temperatures as low as -20°F (-29°C).

Figure 1: GPI M-150 Series Fuel Transfer Pump with manual nozzle and hose.

Кутуда эмне бар

Your GPI M-150 Series Fuel Transfer Pump package includes the following components:

• M-150S 15 GPM pump
• Manual unleaded nozzle
• Сопло кармагыч
• Dispensing hose with static wire
• Factory-installed power cord
• Telescoping suction pipe
• Tank adapter
• Фузер монтажы
• Колдонуучунун колдонмосу (бул документ)

Figure 2: All components included in the GPI M-150 Series Fuel Transfer Pump kit.

Орнотуу жана орнотуу

1. Насос орнотуу

1. Apply Thread Tape: Apply thread tape to all threaded joints, including hoses, suction pipes, and adapters, to ensure a secure, leak-free connection.
2. Bung адаптерин орнотуу: Install the included bung adapter onto your fuel tank. Tighten it down securely with a pipe wrench.
3. Install Gasket and Suction Pipe: Install the gasket and suction pipe onto the pump. Extend the suction pipe to its full length.
4. Насосту орнотуу: Install the pump onto the bung adapter. If your model has a spin collar, tighten it with a pipe wrench. For direct mount models, install directly onto the tank.
5. Шлангды бекитүү: Attach the dispensing hose to the pump. Tighten the hose securely with a crescent wrench to prevent leaks.
6. Соплолорду бекитүү: Attach the manual unleaded nozzle to the end of the dispensing hose.

3-сүрөт: Каптал view of the GPI M-150 pump with nozzle and hose attached.

2. Power Wire Installation (Permanent Connection)

For a permanent connection to your truck's battery:

1. Электр зымынын багыты: Feed the factory-installed power wire down through the gap between your truck bed and cab. Secure the power wire with zip ties (not included) at regular intervals underneath the truck along the frame.
2. Engine Bay Routing: Feed the power wire along the firewall and up into the engine bay. Ensure the wire is clear of the exhaust or any moving components that could damage it.
3. Terminate Negative Wire: Terminate the negative power wire using a ring terminal, crimping it securely.
4. Terminate Positive Wire with Fuse: Crimp the positive wire to one end of the butt connector. Strip 1/3 inch of insulation from each end of the included fuse and crimp the fuse to the other side of the butt connector. Terminate the other end of the fuse wire with a ring terminal.
5. Батареяга туташуу: Ensure the power switch on your pump is turned off. Connect the negative power wire to your battery's negative terminal. Connect the positive power wire (with the fuse assembly) to the positive terminal.

3. Power Wire Installation (Temporary Connection - Optional)

If you prefer a temporary connection using optional battery clamps (sold separately):

1. Тилкелүү зымдар: Strip 1.5 inches of insulation from the fuse wire and the negative wire. Twist the strands tightly.
2. Prepare Clamps: Remove the insulator from one side of each battery clamp and slide the insulators onto the power wires.
3. Insert and Crimp: Insert the stripped fuse wire into the positive clamp and the negative wire into the negative clamp. Fold each stripped wire back to the crimp joint on the clamp and crimp the wire securely.
4. Solder (Optional but Recommended): Apply flux to the stripped wire and solder the wire to the clamp коопсуз байланыш үчүн.
5. Reinstall Insulators: Reinstall the insulator onto the clamp.
6. Батареяга туташуу: Ensure your pump is turned off. Connect the negative clamp to your battery's negative terminal and the positive clamp оң терминалга.

Иштөө нускамалары

The GPI M-150 pump is designed for straightforward operation:

• Күйгүзүү/өчүрүү: The pump features an easy-to-use power switch. Ensure the pump is connected to a 12V DC power source.
• Fuel Compatibility: This pump is suitable for transferring gasoline, E15 ethanol blends, diesel fuel blends (up to B20), and kerosene. Always ensure you are transferring the correct fuel type.
• Бөлүп берүү: Once the pump is powered on, use the manual unleaded nozzle to dispense fuel. The pump delivers a flow rate of up to 15 gallons per minute (57 liters per minute).

Figure 4: The GPI M-150 pump in operation on a truck bed.

Техникалык тейлөө

Regular maintenance ensures the longevity and optimal performance of your GPI M-150 pump:

• Strainer Access: The pump features a unique strainer and poppet design that allows for easy access and maintenance. Regularly check and clean the strainer to prevent debris from entering the pump and affecting its performance.
• Жалпы тазалоо: Keep the pump and its components clean from dirt, dust, and fuel spills.
• Шлангды жана форсунканы текшерүү: Periodically inspect the dispensing hose and nozzle for any signs of wear, cracks, or damage. Replace components as needed to prevent leaks and ensure safe operation.

Figure 5: Key features of the GPI M-150 pump, including easy strainer access for maintenance.

Проблемаларды чечүү

If you encounter issues with your GPI M-150 pump, consider the following common troubleshooting steps:

• Насос иштебейт:
  • Check power connections to the battery.
  • Ensure the power switch on the pump is in the ON position.
  • Inspect the fuse assembly for a blown fuse. Replace if necessary.
  • Батареянын көлөмүн текшериңизtage (12V DC).
• Төмөн агым ылдамдыгы:
  • Check the strainer for clogs and clean if obstructed.
  • Ensure the suction pipe is fully submerged in fuel and not drawing air.
  • Verify all connections are tight to prevent air leaks.
• Агышуулар:
  • Inspect all threaded connections for proper sealing. Re-tighten or re-apply thread tape if needed.
  • Check the hose and nozzle for any damage or cracks.

For more detailed troubleshooting or complex issues, please refer to the full owner's manual or contact GPI product support.

Техникалык шарттар

Кепилдик жана колдоо

The GPI M-150 Series Fuel Transfer Pump is backed by a 2-Year Pump Warranty, ensuring quality and reliability. All M-Series pumps are 100% full-load tested at the factory to guarantee performance.

For any questions regarding installation, maintenance, repair, or warranty, please contact GPI Product Support:

Телефон: 1-800-835-0113

Дүйшөмбү - Жума, саат 8:00 - 5:00 CST

Кошумча ресурстар

For a complete and detailed owner's manual, you can download the PDF version here:

Колдонуучунун толук нускасын жүктөп алыңыз (PDF)