Introduction
This manual provides essential instructions for the setup, operation, and maintenance of your Pro-Ject RM 1.3 Turntable. Please read it thoroughly before use to ensure proper functionality and longevity of your device.
Пакеттин мазмуну
Орнотууну улантуудан мурун, бардык компоненттер бар экенин текшериңиз:
- Pro-Ject RM 1.3 Turntable Unit
- Платтер
- Drive Belt
- Outboard 15V AC Motor
- Электр камсыздоо
- Sumiko Pearl Cartridge (pre-installed or separate)
- Removable RCA Cables
- Каршы салмак
- Конькиге каршы салмак
- Стилус басым өлчөгүч
Орнотуу нускамалары
Follow these steps carefully to set up your turntable:
- Пакеттен чыгаруу: Carefully remove all components from the packaging. Retain packaging for future transport.
- Табакты орнотуу: Place the platter onto the central spindle. Ensure it sits securely and rotates freely.
- Мотор жайгаштыруу: Position the outboard motor unit next to the turntable chassis. The motor pulley should align with the outer rim of the platter.
- Drive Belt Installation: Gently stretch the drive belt around the motor pulley and the outer rim of the platter. Ensure the belt is not twisted.
- Cartridge Installation (if not pre-installed): If your Sumiko Pearl cartridge is not pre-installed, carefully attach it to the tonearm headshell using the provided screws. Ensure correct alignment.
- Каршы салмакты жөндөө: Slide the counterweight onto the rear of the tonearm. Adjust it until the tonearm floats horizontally. Then, set the tracking force according to the cartridge manufacturer's recommendations (typically 1.8g for Sumiko Pearl). Use a stylus pressure gauge for accuracy.
- Anti-skating Adjustment: Attach the anti-skating weight to the tonearm's anti-skating mechanism. Adjust the setting to match the tracking force.
- туташуу Ampөмүр берүүчү: Connect the removable RCA cables from the turntable's output to the "Phono" input of your amplifier or a dedicated phono preamplifier. Ensure the ground wire is connected between the turntable and your ampөмүр бою/мурункуampызы-чууну азайтуу үчүн көтөргүч.
Иштөө нускамалары
- Күйгүзүү: Connect the power supply to the motor unit and a wall outlet. Press the power button on the motor unit to start the platter rotation.
- Ылдамдыкты тандоо: Most turntables offer 33 1/3 RPM and 45 RPM. Ensure the correct speed is selected for your record. (Refer to motor unit for speed selection mechanism, typically a switch or belt position change).
- Рекорд: Carefully place your vinyl record onto the platter.
- Төмөнкү Тонеарм: Gently lift the tonearm using the cueing lever. Position the stylus over the desired track on the record. Slowly lower the cueing lever to allow the stylus to descend onto the record groove.
- Ойнотуу: The record will now play. Adjust the volume on your ampөмүрлүү.
- Ойнотууну токтотуу: At the end of the record, or when you wish to stop, use the cueing lever to lift the tonearm from the record. Return the tonearm to its rest and secure it. Press the power button on the motor unit to stop the platter.
Техникалык тейлөө
- Жазуу тазалоо: Regularly clean your vinyl records using a dedicated record brush or cleaning solution to remove dust and static.
- Стилуска кам көрүү: Use a soft stylus brush to gently clean the stylus tip before and after each play. Brush from back to front. Avoid touching the stylus with your fingers.
- Айланма табакты тазалоо: Wipe the turntable chassis and platter with a soft, dry, lint-free cloth. Avoid abrasive cleaners or solvents.
- Белдик текшерүү: Periodically check the drive belt for wear or stretching. Replace if necessary to maintain accurate playback speed.
Проблемаларды чечүү
Эгерде сиз айланма табагыңыз менен көйгөйлөргө туш болсоңуз, төмөнкү кеңири таралган көйгөйлөрдү жана чечимдерди караңыз:
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| No power / Platter not spinning | Power cable disconnected; faulty power supply/motor; power outlet issue. | Ensure power cable is securely connected. Test the power outlet with another device. If the issue persists, contact support. |
| Уккан же ызылдаган үн | Ground wire not connected; proximity to other electronics; faulty cabling; internal wiring issue. | Ensure the ground wire is securely connected between the turntable and ampөмүр бою/мурункуamplifier. Move the turntable away from other electronic devices. Check RCA cables for damage. If hum persists, it may indicate an internal grounding issue requiring professional service. |
| Distorted sound / Skipping | Incorrect tracking force; worn or dirty stylus; damaged record; incorrect anti-skating. | Re-adjust tracking force and anti-skating. Clean the stylus. Inspect the record for damage. Replace stylus if worn. |
| Ойнотуу ылдамдыгы туура эмес | Incorrect speed selection; worn or stretched drive belt. | Verify the correct speed setting. Inspect and replace the drive belt if it appears worn or loose. |
Техникалык шарттар
| Өзгөчөлүк | Деталь |
|---|---|
| Бренд | Pro-Ject |
| Модел | RM 1.3 |
| Продукциянын өлчөмдөрү | 15 x 4.33 x 13.78 дюйм |
| Элемент Салмагы | 11.15 фунт |
| Камтылган компоненттер | Sumiko Pearl Cartridge, removable RCA cables |
| Мотор түрү | AC мотор |
| Сигнал форматы | Аналог |
| Тtage | 15 вольт (AC) |
| Түс | Кара |
Кепилдик жана колдоо
For warranty information, please refer to the documentation provided with your purchase or visit the official Pro-Ject website. For technical support or service inquiries, please contact your authorized Pro-Ject dealer or the manufacturer's customer service department.
Кепилдик дооматтар үчүн сатып алганыңыздын далилин сактаңыз.
