Introduction
Thank you for choosing the Proel DST110CR Desktop Microphone Stand. This manual provides essential information for the safe and effective assembly, operation, and maintenance of your new microphone stand. Please read this manual thoroughly before use and retain it for future reference.
Коопсуздук нускамалары
- Always ensure the stand is placed on a stable, flat, and level surface to prevent tipping.
- Do not exceed the maximum load capacity of the stand.
- Before making any adjustments, ensure that the microphone and any attached accessories are securely held or removed to prevent accidental drops.
- Tighten all adjustment knobs and locking mechanisms firmly after positioning to ensure stability.
- Keep the stand away from excessive heat, moisture, and corrosive substances.
- Do not attempt to modify or disassemble the stand beyond the instructions provided in this manual.
Пакеттин мазмуну
Сураныч, бардык компоненттер бар экенин текшерүү үчүн пакетти текшериңиз:
- 1 x Proel DST110CR Desktop Microphone Stand Base
- 1 x Telescopic Boom Arm
Жайгашуу
Follow these steps to assemble your Proel DST110CR Microphone Stand:
- Бардык компоненттерди таңгактан чыгарыңыз.
- Insert the main vertical shaft of the telescopic boom arm into the designated opening on the heavy cast iron base.
- Secure the boom arm to the base by tightening the locking mechanism at the base. Ensure it is firm and stable.
- Attach your microphone clip (not included) to the threaded end of the boom arm.
An image showing the fully assembled Proel DST110CR desktop microphone stand, featuring its heavy triangular base, chrome-plated telescopic boom arm, and height adjustment mechanism.
Иштеп жатат
The Proel DST110CR offers adjustable height and boom arm positioning for optimal microphone placement.
Бийиктикти жөндөө:
- Locate the height adjustment knob on the vertical shaft.
- Loosen the knob by turning it counter-clockwise.
- Carefully raise or lower the shaft to your desired height.
- Tighten the knob firmly by turning it clockwise to secure the shaft in place.
Adjusting Boom Arm Angle and Length:
- Locate the boom arm adjustment knob.
- Loosen the knob to allow the boom arm to pivot and extend/retract.
- Position the boom arm to the desired angle and length.
- Tighten the knob firmly to lock the boom arm in position.
Always ensure your microphone is securely attached to the microphone clip before making adjustments or leaving the stand unattended.
Техникалык тейлөө
Proper maintenance will ensure the longevity of your microphone stand:
- Тазалоо: Чаңды жана манжа издерин кетирүү үчүн стендди жумшак, кургак чүпүрөк менен сүртүңүз. Өжөр тактар үчүн бир аз сүртүңүзamp cloth can be used, followed by immediate drying. Do not use abrasive cleaners, solvents, or harsh chemicals, as these can damage the chrome finish and other materials.
- Текшерүү: Periodically inspect all screws, knobs, and joints for tightness. Re-tighten any loose components to maintain stability and safety.
- Сактагыч: When not in use, store the stand in a clean, dry environment, away from extreme temperatures and humidity.
Проблемаларды чечүү
If you encounter issues with your Proel DST110CR, refer to the following common problems and solutions:
- Stand is unstable or wobbles:
Чечим: Ensure the stand is placed on a completely flat and level surface. Check that the boom arm is fully inserted into the base and all adjustment knobs are securely tightened. - Boom arm slips or does not hold position:
Чечим: Ensure the boom arm adjustment knob is tightened firmly. If the issue persists, check for any debris or damage in the locking mechanism. - Height adjustment is difficult or sticky:
Чечим: Ensure the height adjustment knob is fully loosened. Clean the vertical shaft with a dry cloth to remove any dust or grime that might be causing friction.
If you experience problems not covered here, please contact Proel customer support.
Техникалык шарттар
| Өзгөчөлүк | Спецификация |
|---|---|
| Модель номери | DST110 |
| Материал | Металл |
| Түс | Chrome |
| Элемент Салмагы | 3.4 килограмм |
| Негизги өлчөмдөр | 180 x 185 мм (болжол менен) |
| Минималдуу бийиктик | 400 мм |
| Максималдуу бийиктик | 560 мм |
| Боомдун колунун узундугу | 330 mm / 490 mm (telescopic) |
| Өндүрүүчү | Proel |
| Келип чыккан өлкө | Италия |
Кепилдик жана колдоо
For warranty information, please refer to the documentation included with your purchase or visit the official Proel webсайт. Кепилдиктин шарттары аймакка жана сатуучуга жараша өзгөрүшү мүмкүн.
If you require technical assistance or have questions regarding your Proel DST110CR Desktop Microphone Stand, please contact Proel customer support through their official webсайтында же сатып алуу учурунда берилген байланыш маалыматында.
Кепилдик дооматтары үчүн сатып алганыңыздын далилин сактап коюңуз.
