Schneider Electric Square D HOM125 сайгыч автоматтык өчүргүч колдонуучусунун колдонмосу

1. Коопсуздук маалыматы

ЭСКЕРТҮҮ: Risk of electric shock, explosion, or arc flash. Installation and maintenance must be performed by qualified personnel only. Read these instructions carefully and look at the equipment to become familiar with the device before trying to install, operate, service, or maintain it.

• Always turn off power at the main disconnect before working on electrical equipment.
• Томду колдонуңузtage tester to confirm power is off before touching any wires.
• Тиешелүү жеке коргонуу шаймандарын (ЖКК) кийиңиз.
• Бардык жергиликтүү жана улуттук электр эрежелерин сактаңыз.
• This circuit breaker is designed for use in Square D Homeline load centers only.

2. Продукт бүтүп калдыview

The Schneider Electric Square D HOM125 is a 25 Amp, single-pole, thermal-magnetic plug-in circuit breaker designed for use in Homeline load centers. It provides overcurrent protection for electrical circuits, safeguarding wiring and equipment from damage due to overloads and short circuits. This breaker has a 10 kA interrupting rating and is rated for 120/240 VAC at 50/60 Hz.

Негизги өзгөчөлүктөрү:

• Түрү: Thermal-Magnetic Branch Circuit Breaker
• Учурдагы рейтинг: 25 Amperes
• поляктар: 1-уюл
• Тtage Рейтинг: 120/240 Бунёдкор
• Үзгүлтүксүз баа: 10 кА
• Монтаждоо: Плагин
• Терминал түрү: Screw Clamp
• Шайкештик: Square D Homeline Load Centers

1-сүрөт: Жогорудан төмөн view of the Square D HOM125 circuit breaker, showing the toggle switch and rating labels.

3. Орнотуу

МААНИЛҮҮ: Орнотуу бардык колдонулуучу электр коддоруна ылайык квалификациялуу электрик тарабынан аткарылышы керек.

1. Жүктөө борборун даярдоо:
   • Ensure all power to the load center is OFF at the main disconnect. Verify with a voltage сыноочу.
   • Remove the load center cover.
2. Connect the Circuit Wire:
   • Strip approximately 1/2 inch (12.7 mm) of insulation from the circuit wire (14 to 8 AWG aluminum/copper, or two 14 to 10 AWG copper wires).
   • Insert the stripped end of the circuit wire into the screw clamp terminal on the breaker.
   • Tighten the terminal screw firmly to the specified torque (refer to load center instructions for exact torque specifications). Ensure the wire is securely fastened and no bare strands are exposed outside the terminal.
   

   2-сүрөт: Арткы view of the HOM125 circuit breaker, highlighting the screw clamp terminals for wire connection.

3. Install the Breaker:
   • Position the breaker so that the clip on the back engages with the mounting rail in the load center.
   • Align the plug-on connector with the bus bar stab.
   • Firmly press the breaker onto the bus bar until it is fully seated and clicks into place.
   

   3-сүрөт: Side view of the HOM125 circuit breaker, illustrating the plug-in connection mechanism.
4. Күчтү калыбына келтирүү:
   • Replace the load center cover.
   • Turn the main disconnect power back ON.
   • Switch the newly installed circuit breaker to the "ON" position.

4. Операция

The HOM125 circuit breaker operates as a protective device for your electrical circuit. It has two primary states: ON and OFF, and a tripped state.

• ON позициясы: When the toggle handle is in the "ON" position, power is supplied to the connected circuit.
• ӨЧҮРҮҮ абалы: When the toggle handle is manually moved to the "OFF" position, power to the connected circuit is interrupted.
• БУРУЛУП КАЛГАН абал: If an overload or short circuit occurs, the breaker will automatically move to a central, "TRIPPED" position (often indicated by the handle being between ON and OFF, or slightly past OFF). This indicates that the breaker has interrupted the circuit to prevent damage.

4-сүрөт: Жакын план view of the HOM125 circuit breaker's toggle switch, which indicates the ON, OFF, or TRIPPED status.

Resetting a Tripped Breaker

If the circuit breaker trips, follow these steps:

1. Себебин аныктоо: Unplug or turn off any appliances or devices on the affected circuit that may have caused the overload or short circuit.
2. Breakerди баштапкы абалга келтирүү:
   • First, firmly push the breaker handle completely to the "OFF" position. You may feel a click.
   • Андан кийин, тутканы "ON" абалына бекем түртүңүз.
3. Монитор: If the breaker trips again immediately, there may be a persistent issue (e.g., a short circuit or a faulty appliance). Do not repeatedly reset the breaker without addressing the underlying problem. Consult a qualified electrician.

5. Техникалык тейлөө

The Square D HOM125 circuit breaker is designed for reliable, long-term operation with minimal maintenance. However, periodic inspection is recommended.

• Визуалдык текшерүү: Annually, or as needed, inspect the breaker for any signs of physical damage, discoloration, or loose connections. Ensure the toggle handle moves freely.
• Тазалоо: If necessary, gently clean the exterior of the breaker with a dry, lint-free cloth. Do not use liquids or abrasive cleaners. Ensure power is off before cleaning.
• Туташуу текшерүү: Periodically, with power off, verify that the wire terminal screws are tight. Loose connections can cause overheating.

If any issues are observed, consult a qualified electrician for assessment and potential replacement.

6. Кыйынчылыктарды

Бул бөлүмдө сиздин автоматтык өчүргүчүңүз менен кездешүүсү мүмкүн болгон жалпы маселелер каралат.

7. Техникалык шарттар

8. Кепилдик жана колдоо

For specific warranty information, please refer to the documentation provided with your Square D Homeline load center or contact Schneider Electric customer support directly. General product support and technical assistance can be obtained through the official Schneider Electric webсайтка же кардарларды тейлөө бөлүмүнө кайрылыңыз.

Schneider Electric Байланыш маалыматы:

• Официалдуу Webсайт
• Refer to your load center manual for specific regional support contacts.