1. Продукт бүтүп калдыview
This manual provides detailed instructions for the installation, maintenance, and troubleshooting of the Hüppe Universal Drain Seal Strip. This seal strip is designed to ensure water tightness for specific shower enclosures, preventing water leakage.
It is compatible with 4-corner shower enclosures featuring 8mm glass thickness. Please note, this seal strip is жок suitable for 1/4 circle shower enclosures.
2. Техникалык шарттар
| Өзгөчөлүк | Деталь |
|---|---|
| Модель номери | 070051000 |
| Бренд | Hüppe |
| Материал | Stainless Steel, Glass (referring to the enclosure, the strip itself is likely plastic/rubber) |
| Түс | Steel Grey (Stainless Steel) |
| Узундук | 1000mm (can be cut to size) |
| Бийиктик | 20mm (can be shortened to 13mm) |
| Glass Thickness Compatibility | 8mm (for 4-corner shower enclosures only) |
| Салмагы | 80 г |
| Шайкеш моделдер | Studio 5000, Jette Joop 1002, Target, Refresh, Studio Paris + Berlin, Manufaktur Studio, 2003E |
Figure 1: Dimensional diagram of the seal strip, indicating a total height of 20mm and a lower section height of 13mm.
3. Орнотуу боюнча колдонмо
3.1 Керектүү куралдар
- Өлчөөчү лента же сызгыч
- Fine-tooth saw or sharp utility knife (for cutting plastic/rubber)
- Маркер
3.2 Орнотуу кадамдары
- Өлчөм: Carefully measure the length of the bottom edge of your shower enclosure door where the seal strip will be installed.
- Өлчөмгө кесүү: Using the measured length, mark the Hüppe seal strip. Cut the strip precisely to the required length using a fine-tooth saw or a sharp utility knife. Ensure a clean, straight cut for optimal fit.
- Adjust Height (if necessary): The seal strip has a total height of 20mm and can be shortened to 13mm if required for your specific shower enclosure setup. Refer to Figure 1 for visual guidance. If shortening is needed, carefully trim the lower part of the strip.
- Тирке: Slide the U-shaped channel of the seal strip onto the bottom edge of the 8mm thick glass shower door. Ensure it is firmly seated and extends evenly across the entire width of the door. The flexible lip should face inwards towards the shower tray to direct water back into the shower.
- Сыноо: Close the shower door and check for proper fit and seal. Run water along the bottom edge of the door to verify that no water leaks out.
4. Иштөө принциби
The Hüppe Universal Drain Seal Strip functions by creating a barrier at the bottom of your shower door. Its design, with a flexible lip, directs water that runs down the glass back into the shower tray, preventing it from escaping onto the bathroom floor. Proper installation ensures a tight seal, maintaining a dry bathroom environment.
5. Техникалык тейлөө
- Тазалоо: Regularly clean the seal strip with mild soap and water. Avoid abrasive cleaners or harsh chemicals, as these can damage the material and reduce its effectiveness.
- Текшерүү: Periodically inspect the seal strip for signs of wear, cracking, or discoloration. Over time, seals can degrade, affecting their water-tight properties.
- Алмаштыруу: If the seal strip shows significant signs of wear or no longer provides an effective seal, it should be replaced to maintain the functionality of your shower enclosure.
6. Кыйынчылыктарды
6.1 Суунун агып кетиши
- Маселе: Water is leaking from under the shower door.
- Мүмкүн болгон себептер жана чечимдер:
Туура эмес орнотуу: Ensure the seal strip is fully seated on the glass and the flexible lip is facing inwards towards the shower tray. Re-adjust if necessary.
Improper Length: The strip might be too short, leaving gaps. Measure and cut a new strip if needed.
Worn or Damaged Seal: The seal strip may be old or damaged. Inspect for cracks or hardening. Replace the seal strip if it is compromised.
Incorrect Height: If the strip was shortened, ensure it still makes proper contact with the shower tray. The height might be too low. Consider a new strip with appropriate height.
6.2 Difficulty Closing Door
- Маселе: The shower door is difficult to close after installing the seal strip.
- Мүмкүн болгон себептер жана чечимдер:
Seal Strip Too Thick/Long: The seal strip might be too thick for the gap between the door and the frame/tray, or it might be too long, causing it to bunch up. Ensure the strip is correctly sized and trimmed.
Incorrect Height: If the strip is too tall, it might create excessive friction. Consider trimming the height to 13mm if applicable and if it still provides a sufficient seal.
7. Кепилдик жана колдоо
For specific warranty information regarding your Hüppe Universal Drain Seal Strip, please refer to the purchase documentation or contact the retailer from whom you purchased the product. For technical support or further assistance, please contact Hüppe customer service directly or the authorized seller.
Сатуучунун байланышы: Wilh.Heunert GmbH & Co.KG
For more information, you may visit the official Hüppe website or consult your product's original packaging.
