Introduction
This instruction manual provides essential information for the safe installation, operation, and maintenance of the Franklin Electric 1.5 HP Submersible Water Pump Control Box, Model 14G19-24-00904B. This control box is designed to manage and protect 230V, single-phase, 3-wire + ground submersible motors up to 1.5 horsepower. Please read this manual thoroughly before proceeding with installation or service.
Коопсуздук маалыматы
ЭСКЕРТҮҮ: ЭЛЕКТР ТОГУ КОРКУНУЧУ.
- Always disconnect all power to the control box and pump motor before attempting any installation, maintenance, or troubleshooting. Failure to do so can result in severe injury or death.
- Installation and service must be performed by qualified personnel in accordance with all local and national electrical codes.
- Ensure proper grounding of the control box and pump motor.
- Do not operate the pump or control box if any components are damaged.
- This control box contains capacitors that can store electrical charge even after power is disconnected. Exercise caution when handling internal components.
Орнотуу жана орнотуу
Proper installation is critical for the safe and efficient operation of your submersible pump system. Refer to the wiring diagram provided with the control box and adhere to all applicable electrical codes.
- Монтаждоо: Select a dry, accessible location for mounting the control box. Ensure it is protected from direct weather exposure and physical damage. Use appropriate fasteners to secure the box firmly to a stable surface.
- Электр энергиясын өчүрүү: Before making any electrical connections, ensure that the main power supply to the pump circuit is completely disconnected at the circuit breaker or fuse panel. Verify with a voltage сыноочу.
- Зымдарды туташтыруу:
- Connect the incoming power supply (230V, single-phase) to the designated terminals within the control box.
- Connect the 3-wire + ground submersible motor leads to the corresponding terminals (typically L1, L2, and Ground for power, and R, Y, B for motor windings). Ensure correct phase rotation if applicable, though for single-phase, this refers to matching the motor leads to the correct capacitor/relay connections.
- Ensure all connections are tight and secure. Use appropriate wire gauges as specified by electrical codes and the pump motor manufacturer.
- Негиздөө: Connect the system ground wire to the designated grounding terminal within the control box.
- Короонун жабылышы: Once all connections are made and verified, securely close the control box cover.
- Электр энергиясын калыбына келтирүү: Restore power to the circuit only after all installation steps are complete and verified.
Сүрөт 1: Сырткы көрүнүш view of the Franklin Electric 1.5 HP Submersible Water Pump Control Box. This image shows the gray metal enclosure with the Franklin Electric logo and warning labels prominently displayed on the front. A mounting bracket is visible at the top.
Сүрөт 2: Интерьер view of the Franklin Electric 1.5 HP Submersible Water Pump Control Box. The cover is removed, revealing the internal components including capacitors, relays, and terminal blocks for wiring connections. Wires are visible, indicating the pre-wired nature of some internal components.
Иштөө нускамалары
The control box operates automatically in conjunction with your pump's pressure switch or other control devices. It provides the necessary starting components and overload protection for the submersible motor.
- Once properly installed and powered, the control box will energize the pump motor when a demand for water is detected (e.g., pressure switch closes).
- The control box includes an overload protector. If the pump motor draws excessive current, the overload protector will trip, shutting off power to the motor to prevent damage.
- To reset the overload protector, locate the reset button (typically labeled "OVERLOAD RESET" or similar) on the exterior or interior of the control box. Press the button firmly. If the overload trips repeatedly, investigate the cause before continuous resetting.
Техникалык тейлөө
Regular inspection can help ensure the longevity and reliable operation of your control box.
- Визуалдык текшерүү: Periodically inspect the control box for any signs of physical damage, corrosion, or loose connections. Ensure the cover is securely closed.
- Тазалоо: Keep the exterior of the control box clean and free of dust or debris. Do not use harsh chemicals or abrasive cleaners.
- Internal Inspection (by qualified personnel only): If internal inspection is required, ensure power is disconnected. Check for signs of overheating, such as discolored wires or components. Verify that capacitors are not bulging or leaking.
Проблемаларды чечүү
Before attempting any troubleshooting, ensure power is disconnected. If you are unsure about any step, contact a qualified electrician or pump technician.
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| Насос иштебейт. | No power to control box. Tripped overload protector. Faulty pressure switch or control device. Motor or pump issue. | Check circuit breaker/fuses. Press overload reset button. Inspect pressure switch wiring and operation. Consult a pump technician for motor/pump diagnosis. |
| Overload trips frequently. | Төмөн үнtage. Motor drawing excessive current (e.g., worn pump, clogged impeller). Faulty capacitors in control box. Incorrect motor wiring. | Тастыктоо томtage. Inspect pump and motor for mechanical issues. Have capacitors tested/replaced by qualified personnel. Зымдардын схемага ылайык туташканын текшериңиз. |
| Насос үзгүлтүксүз иштейт. | Бузулуу басым өчүргүч. Leak in plumbing system. Control box relay stuck. | Inspect/replace pressure switch. агып кетүүлөрдү текшерүү. Consult qualified personnel for control box inspection. |
Техникалык шарттар
- Модел: 14G19-24-00904B
- Ат күчү (HP): 1.5 HP
- Тtage: 230 вольт
- Фаза: Бир фазалуу
- Мотор шайкештиги: 3-wire + Ground Submersible Motors
- Өндүрүүчү: Франклин электр
- UPC: 755717496515
- Продукциянын өлчөмдөрү: Болжол менен 10.79 x 8.43 x 6.14 дюйм
- Элемент Салмагы: Болжол менен 6.15 фунт
- Кубат булагы: Электр зымдары
Image 3: Product label from the Franklin Electric control box packaging. This label displays key specifications such as HP (1/1.5), Volts (230), Hz (60), PH (1), and the Part Number (14G19-24-00904B), confirming the model and electrical characteristics.
Кепилдик маалымат
Warranty coverage for the Franklin Electric 1.5 HP Submersible Water Pump Control Box is provided by the manufacturer. Please refer to the warranty documentation included with your purchase or visit the official Franklin Electric webтолук шарттары жана шарттары үчүн сайт. Кепилдик дооматтар үчүн сатып алганыңыздын далилин сактаңыз.
Колдоо
For technical assistance, replacement parts, or further inquiries, please contact Franklin Electric customer support or a certified Franklin Electric service provider. Always provide the model number (14G19-24-00904B) and serial number (if applicable) when seeking support.
You can find contact information on the official Franklin Electric webсайт: www.franklinwater.com
