Onyx Re-Arm Kit for 3200 Automatic/Manual Inflatable PFD Instruction Manual

1. Киришүү

This instruction manual provides essential information for the proper use, installation, and maintenance of the Onyx Re-Arm Kit, model 3200. This kit is designed specifically for Onyx automatic/manual inflatable personal flotation devices (PFDs) that require a 24-gram CO2 cylinder. Adhering to these instructions ensures the continued safety and functionality of your inflatable PFD.

2. Продукт бүтүп калдыview жана компоненттер

The Onyx Re-Arm Kit 3200 contains the necessary components to restore your inflatable PFD to an operational state after it has been deployed or if components require replacement due to expiration or damage.

Комплекттин мазмуну:

• One (1) 24 gram CO2 cylinder with 1/2" thread
• One (1) Green indicator clip
• One (1) Yellow water-soluble bobbin (for automatic inflation mechanism)

This image displays the three primary components of the Onyx Re-Arm Kit: a 24-gram CO2 cylinder with a threaded neck, a yellow water-soluble bobbin, and a green indicator clip. These parts are crucial for the proper function of an automatic/manual inflatable PFD.

3. Setup and Installation (Re-Arming Instructions)

Before re-arming, ensure your PFD is completely deflated and dry. Always refer to your specific Onyx PFD's instruction manual for detailed re-arming procedures, as steps may vary slightly by model. The following are general guidelines.

General Re-Arming Steps:

1. Remove Used Components: If the PFD has been deployed, carefully remove the spent CO2 cylinder by unscrewing it. Discard the old cylinder. Remove any old bobbin or indicator clips.
2. Inspect PFD: Thoroughly inspect the PFD for any damage, tears, or punctures. Ensure the inflation bladder is intact and the oral inflation tube cap is secure.
3. Install New Bobbin (for Automatic PFDs): Locate the automatic inflation mechanism. Insert the new yellow water-soluble bobbin into the designated slot. Ensure it is seated correctly according to your PFD's manual. This bobbin dissolves in water, triggering automatic inflation.
4. Install New CO2 Cylinder: Carefully screw the new 24-gram CO2 cylinder into the inflation mechanism. Turn clockwise until it is hand-tight. Ашыкча катуулабагыла. Ensure the cylinder is fully seated.
5. Install Green Indicator Clip: Attach the green indicator clip to the inflation mechanism. This clip typically confirms that the PFD is armed and ready for use. Refer to your PFD manual for the exact placement.
6. Repack PFD: Once re-armed, carefully fold and repack the PFD according to its original instructions. Ensure the pull-cord for manual inflation is accessible and not obstructed.

Маанилүү: Always ensure the CO2 cylinder is new and undamaged. Never use a cylinder that has been punctured or shows signs of corrosion.

4. Operating the Re-Armed PFD

After re-arming, your Onyx PFD is ready for use. It offers both automatic and manual inflation capabilities.

• Автоматтык инфляция: When submerged in water, the yellow water-soluble bobbin will dissolve, triggering the CO2 cylinder to inflate the PFD automatically.
• Мануалдык инфляция: In an emergency, or if automatic inflation is desired before water entry, pull the manual inflation cord firmly downwards. This will activate the CO2 cylinder and inflate the PFD.
• Оозеки инфляция: For additional buoyancy or to top off air, use the oral inflation tube. Remove the cap, inflate by mouth, and replace the cap securely.

Always ensure the PFD is worn correctly and securely before engaging in water activities.

5. Техникалык тейлөө жана текшерүү

Regular inspection and proper maintenance are crucial for the reliability of your inflatable PFD and its re-arm kit components.

• Ар бир колдонуудан мурун:
  • Check the green indicator clip to ensure it is properly installed and indicates the PFD is armed.
  • Verify the CO2 cylinder is securely attached and shows no signs of damage or corrosion.
  • Inspect the PFD fabric for any tears, punctures, or excessive wear.
• Жылдык текшерүү:
  • Perform a full inflation test by orally inflating the PFD and leaving it inflated for 24 hours to check for leaks.
  • Check the expiration date on the CO2 cylinder and the bobbin. Replace if expired.
  • Clean the PFD with mild soap and water, then allow it to air dry completely before repacking.
• Сактагыч: Store the PFD in a cool, dry place, away from direct sunlight and extreme temperatures.

Replace the re-arm kit components immediately after each inflation or if any component is damaged or expired.

6. Кыйынчылыктарды

This section addresses common issues related to the re-arm kit and PFD inflation.

7. Техникалык шарттар

• Бренд: Оникс
• Модел: Re-Arm Kit 3200
• CO2 Cylinder Size: 24 грамм
• CO2 Cylinder Thread: 1/2 дюйм
• Шайкештик: Onyx A/M 24 Automatic/Manual Inflatable PFD (Model 3200 series)
• Комплекттин компоненттери: 24g CO2 cylinder, green indicator clip, yellow water-soluble bobbin
• Буюмдун болжолдуу Салмагы: 0.6 фунт (9.6 унция)
• Approximate Product Dimensions: 8"L x 6"Вт (упаковка)
• UPC: 043311002295

8. Кепилдик жана колдоо

For specific warranty information regarding your Onyx Re-Arm Kit or PFD, please refer to the documentation included with your original PFD purchase or visit the official Onyx Outdoor website. For technical support or inquiries, please contact Onyx Outdoor customer service directly.

Эскертүү: Using non-Onyx approved re-arm kits or components may void your PFD's warranty and compromise its safety performance.