Masonite эки бүктөлүүчү 6 панелдүү эшиктин колдонмосу

Introduction

This manual provides comprehensive instructions for the proper installation, operation, and maintenance of your Masonite Bi-Fold 6-Panel Door. Please read all instructions carefully before beginning installation to ensure safe and correct assembly and long-term performance.

Коопсуздук маалыматы

• Орнотуу учурунда ар дайым коргоочу көз айнек жана кол кап сыяктуу тиешелүү жеке коргонуу шаймандарын (ЖКК) кийиңиз.
• Жумуш аймагы жакшы жарыктандырылсын жана тоскоолдуктар жок болсун.
• Handle the door panels with care to prevent injury or damage to the product.
• Майда тетиктерди жана жабдууларды балдардан алыс кармаңыз.
• Эгер кандайдыр бир кадамга ишенбесеңиз, квалификациялуу адиске кайрылыңыз.

Компоненттердин жана тетиктердин тизмеси

Verify that all components are present before beginning installation. If any parts are missing or damaged, contact Masonite customer support.

• Prefinished Bi-Fold Door Panels (2 sections)
• Top Track
• Pivot Brackets (top and bottom)
• Guide Wheel/Roller
• Hinges (pre-attached)
• Door Knob/Pull (may be included or sold separately)
• Fasteners (screws)

Image: A white, prefinished bi-fold door with a six-panel design. The door consists of two vertical sections, each with three recessed rectangular panels, designed to fold inward for space-saving operation.

Орнотуу жана орнотуу

Керектүү куралдар:

• Өлчөө лентасы
• Карандаш
• Бургулоо
• Screwdriver
• Деңгээл
• Saw (if trimming is required)

Орнотуу кадамдары:

1. Ачылышын даярдоо: Ensure the door opening is plumb, level, and square. Measure the height and width to confirm it matches the door dimensions (30x80 inches).
2. Top Track орнотуу: Secure the top track inside the door frame header using the provided fasteners. Ensure it is level and centered.
3. Install Bottom Pivot Bracket: Mount the bottom pivot bracket to the floor or door frame sill, aligning it with the top track.
4. Attach Door Hardware: Insert the top pivot pin into the pre-drilled hole on the top edge of the door panel. Attach the guide wheel/roller to the other top edge of the door panel. Insert the bottom pivot pin into the pre-drilled hole on the bottom edge of the door panel.
5. Эшикти илип коюңуз: Lift the door panels and insert the top pivot pin into the top pivot bracket in the track. Guide the bottom pivot pin into the bottom pivot bracket. Engage the guide wheel/roller into the top track.
6. Жөндөө жана тегиздөө: Adjust the pivot pins and guide wheel to ensure the door hangs plumb and operates smoothly. The door should close flush with the frame.
7. Install Door Knob/Pull: Attach the door knob or pull according to its specific instructions.

Иштөө нускамалары

The Masonite Bi-Fold Door is designed for smooth and quiet operation. To open the door, gently pull the door knob or handle, allowing the panels to fold inward. To close, push the door panels until they are fully extended and meet in the center of the opening.

Техникалык тейлөө

• Тазалоо: Clean the prefinished door surface with a soft, damp кездеме жана жумшак самын. Абразивдүү тазалагычтардан же финишке зыян келтирүүчү катаал химиялык заттардан алыс болуңуз.
• Аппараттык камсыздоону текшерүү: Periodically inspect all hardware, including hinges, pivots, and the top track, for any signs of wear or looseness. Tighten screws as needed.
• Майлоо: Apply a silicone-based lubricant to the top track and guide wheel/roller annually to ensure continued smooth operation.
• Боёкту оңдоо: If the prefinished surface gets scratched or chipped, use a matching white paint to touch up the affected area.

Проблемаларды чечүү

Техникалык шарттар

Кепилдик жана колдоо

For information regarding product warranty or to obtain technical support, please refer to the official Masonite webсайтка же түздөн-түз кардарларды тейлөө бөлүмүнө кайрылыңыз. Сатып алганыңыздын далили катары сатып алуу дүмүрчөгүңүздү сактаңыз.

Masonite Customer Service: www.masonite.com/contact-us