Introduction
Thank you for choosing the BN-LINK Countdown Digital Wall Timer Switch. This manual provides essential information for the safe installation, operation, and maintenance of your new timer switch. Please read these instructions thoroughly before installation and use, and retain them for future reference.
Коопсуздук маалыматы
- ЭСКЕРТҮҮ: Электр шок коркунучу. Installation requires working with high voltage wiring. Always turn off power at the circuit breaker before installation.
- This device requires a Нейтралдуу зым for proper operation. Ensure your electrical box has a neutral wire (typically white) before attempting installation.
- Эгерде сиз орнотуу процессинин кайсы бир бөлүгү боюнча күмөн санасаңыз, квалификациялуу электрикке кайрылыңыз.
- Rated 125V, 60 Hz, 15A/1875W Resistive or General Purpose, 10A/1250W Ballast or Tungsten, ½ HP, TV-5.
- ETL listed, conforms to UL Std. 60730-1, 60730-2-7.
Пакеттин мазмуну
- BN-LINK Countdown Digital Wall Timer Switch
- Дубал плитасы
- Wire Nuts
- Монтаждоо бурамалар
- Instruction Manual
Техникалык шарттар
| Өзгөчөлүк | Спецификация |
|---|---|
| Иштөө режими | КҮЙГҮЗҮҮ ӨЧҮРҮҮ |
| Учурдагы рейтинг | 15 Amps |
| Operating Voltage | 125 вольт |
| Ватtage | 1875 Ватт |
| Байланыш түрү | Адатта ачык |
| Туташтыргыч түрү | Зымдуу |
| Өлчөмдөрү (L x W x Y) | 4.2 x 1.8 x 2 дюйм |
| Элемент Салмагы | 5.6 унция |
| Шайкеш түзмөктөр | Incandescent, fluorescent, and LED lighting, bathroom exhaust fans, heaters |
Орнотуу жана орнотуу
Баштоодон мурун: Turn off power at the circuit breaker for the switch location. Verify power is off using a voltage сыноочу.
Wiring Instructions
- Зымдарды аныктоо: Carefully remove your existing switch and identify the Hot, Load, Neutral, and Ground wires in your wall box. A neutral wire (typically white) is required.
- Зымдарды туташтыруу: Use the provided wire nuts to connect the BN-LINK timer switch wires to your household wires as follows:
- Black Wire (Timer) чейин Hot Wire (Wall Box)
- Red Wire (Timer) чейин Load Wire (Wall Box)
- White Wire (Timer) чейин Neutral Wire (Wall Box)
- Green Wire (Timer) чейин Ground Wire (Wall Box)
- Коопсуз зымдар: Ensure all wire connections are secure and insulated with wire nuts.
Mounting and Finishing
- Которгучту киргизүү: Carefully push the wired timer switch into the wall box.
- Коопсуз которуу: Use the provided screws to secure the timer switch to the wall box.
- Дубал плитасын бекитүү: Mount the included wall plate over the switch.
- Күчтү калыбына келтирүү: Электрди өчүргүчтөн кайра күйгүзүңүз.
Орнотуу боюнча видео көрсөтмө
Иштөө нускамалары
1. Инициализация
When the timer is first powered, all indicator lights will briefly illuminate and then turn off after a self-diagnosis process. This indicates the timer is ready for use.
2. Setting a Countdown Program
To activate a countdown, simply press the button corresponding to your desired time (5, 10, 20, 30, 45, or 60 minutes). The indicator light on the selected button will illuminate, and the countdown will begin. The connected device will turn off automatically once the countdown is complete.
3. Shifting to Another Countdown Program
If a countdown is active and you wish to change the duration, press a different countdown button. The indicator light on the previously active button will turn off, and the light on the newly selected button will illuminate. The new countdown program will then begin.
4. Activating the Daily Repeat Function
To enable the daily repeat function, press the КАЙТАЛОО button while a countdown program is running. The indicator light on the КАЙТАЛОО button will illuminate. The current program will automatically run again at the same time on the following day.
5. Deactivating the Daily Repeat Function (2 Ways)
There are two methods to deactivate the daily repeat function:
- Press REPEAT Button: басыңыз КАЙТАЛОО button again. Its indicator light will turn off. This will deactivate the repeat function for any ongoing program.
- Press ON/OFF Button: басыңыз КҮЙГҮЗҮҮ/ӨЧҮРҮҮ button. This will terminate the ongoing program and also deactivate the daily repeat function.
6. Termination of a Countdown Program
A countdown program will terminate automatically when its set time expires. The indicator light for that program will turn off, and the power output to the connected device will be cut off.
7. Always On Mode
If a countdown is already running, or if the daily repeat function is active, press the КҮЙГҮЗҮҮ/ӨЧҮРҮҮ button twice to set the timer to 'Always On' mode. The КҮЙГҮЗҮҮ/ӨЧҮРҮҮ indicator light will illuminate, and the device will remain powered indefinitely.
If the timer is in 'Off' mode, press the КҮЙГҮЗҮҮ/ӨЧҮРҮҮ button once to set the timer to 'Always On' mode. The КҮЙГҮЗҮҮ/ӨЧҮРҮҮ индикатор жарыгы күйөт.
8. Terminating Always On Mode
To terminate 'Always On' mode:
- Press ON/OFF Button: басыңыз КҮЙГҮЗҮҮ/ӨЧҮРҮҮ баскычын бир жолу. The КҮЙГҮЗҮҮ/ӨЧҮРҮҮ indicator light will turn off, and the power output will be cut off.
- Select Countdown Program: Press any of the preset countdown buttons (5, 10, 20, 30, 45, or 60 minutes). This will initiate a new countdown program and terminate 'Always On' mode.
9. Restarting a Running Countdown Program
To restart a running countdown program:
- Terminate and Re-select: басыңыз КҮЙГҮЗҮҮ/ӨЧҮРҮҮ button to terminate the current program, then immediately press the desired countdown button to restart it.
- Shift Program: Alternatively, press a different countdown button, and then press the original countdown button you wish to restart.
Техникалык тейлөө
To maintain your BN-LINK Countdown Digital Wall Timer Switch, ensure the power is off at the circuit breaker before cleaning. Wipe the surface with a soft, damp cloth. Do not use harsh chemicals or abrasive cleaners. Regular inspection for any loose wiring or damage is recommended.
Проблемаларды чечүү
- Таймер күйбөй жатат: Check the circuit breaker to ensure power is supplied. Verify all wiring connections are secure, especially the neutral wire.
- Countdown not starting: Ensure a specific time button is pressed and its indicator light is on.
- Repeat function not working: Confirm the REPEAT indicator light is illuminated after activation. If not, press the REPEAT button again while a countdown is active.
- Device not turning off: Check if the timer is in 'Always On' mode (ON/OFF indicator illuminated). If so, press the ON/OFF button to turn it off.
Кепилдик жана колдоо
BN-LINK products are designed for reliability and performance. For any questions regarding installation, operation, or troubleshooting, please contact BN-LINK customer support. We are always here to assist you.
For further information, please refer to the included guide or visit our official webсайт.
