WaterCop Wireless Flood Sensor (WCDFS1) Instruction Manual

1. Киришүү

The WaterCop Wireless Flood Sensor (WCDFS1) is designed to detect the presence of water and transmit a wireless signal to a compatible WaterCop automatic water shut-off system. This system helps prevent water damage by automatically activating the shut-off valve when a leak is detected.

This sensor operates wirelessly, providing flexible placement options up to 200 feet from the main WaterCop system. It is powered by standard AA alkaline batteries.

2. Пакеттин мазмуну

• WaterCop Wireless Flood Sensor (WCDFS1)
• Remote Probe with cable
• Монтаждоочу жабдыктар (буроолор, анкерлер)
• Бул Колдонмо

3. Коопсуздук маалыматы

• Орнотуудан жана иштетүүдөн мурун бардык көрсөтмөлөрдү окуп чыгыңыз.
• Do not expose the sensor to extreme temperatures or direct sunlight.
• Батареялардын полярдуулук белгилерине ылайык туура орнотулганын текшериңиз.
• Replace batteries annually or when indicated by the WaterCop system.
• Бул аппарат имараттын ичинде гана колдонууга арналган.

4. Орнотуу жана орнотуу

4.1 Батареяны орнотуу

The WaterCop WCDFS1 sensor requires two (2) AA alkaline batteries (not included).

1. Сенсорду кылдаттык менен ачыңыз casing. Refer to the diagram for assistance.
2. Insert two AA alkaline batteries, observing the correct polarity (+/-) as marked inside the battery compartment.
3. Сенсорду жабуу casing коопсуз.

A pair of standard AA alkaline batteries should operate the sensor for approximately one year.

4.2 Сенсордун жайгашуусу

Place the sensor in areas prone to water leaks, such as near water heaters, washing machines, dishwashers, sinks, toilets, or in basements.

The sensor transmits a wireless signal up to 200 feet to the WaterCop control unit. Consider potential obstructions like thick walls or metal objects that may reduce signal range.

The remote probe should be positioned directly on the floor or surface where water accumulation is most likely to occur.

4.3 Pairing with WaterCop System

The WCDFS1 sensor is compatible with all WaterCop systems. Refer to your specific WaterCop control unit's manual for detailed instructions on how to pair new sensors. Generally, this involves placing the control unit into a "learn" mode and then activating the sensor.

4.4 Монтаждоо

The sensor unit can be wall-mounted using the provided hardware. Ensure the remote probe cable reaches the desired detection area.

5. Операция

Once installed and paired, the WaterCop Wireless Flood Sensor continuously monitors for the presence of water at its remote probe.

Upon detecting water, the sensor immediately transmits a wireless signal to the WaterCop control unit.

The WaterCop control unit, upon receiving this signal, will activate the automatic shut-off valve, thereby stopping the water supply to prevent further damage.

The sensor will continue to transmit the alarm signal until the water is no longer detected by the probe.

6. Техникалык тейлөө

6.1 Батареяны алмаштыруу

Replace the AA alkaline batteries annually or when the WaterCop control unit indicates a low battery signal from the sensor.

1. Сенсорду ачыңыз casing.
2. Эски батарейкаларды алып чыгып, жоопкерчиликтүү түрдө жок кылыңыз.
3. Туура полярдуулукту камсыз кылуу менен эки жаңы AA щелочтуу батарейканы салыңыз.
4. Сенсорду жабуу casing коопсуз.

6.2 Тазалоо

Periodically inspect the sensor and probe for dust or debris. Clean with a soft, dry cloth. Do not use abrasive cleaners or immerse the unit in water.

6.3 Сыноо

It is recommended to test the sensor's functionality periodically (e.g., every 3-6 months).

1. Place a small amount of water (e.g., a few drops) on the remote probe.
2. Observe if the WaterCop control unit receives the alarm signal and activates the shut-off valve.
3. Remove the water from the probe and verify that the WaterCop system resets or allows manual reset.
4. Refer to your WaterCop control unit's manual for specific testing procedures.

7. Кыйынчылыктарды

7.1 Sensor not detecting water:

• Ensure the remote probe is making good contact with the surface.
• Батареянын деңгээлин текшерип, керек болсо алмаштырыңыз.
• Verify the sensor is correctly paired with the WaterCop control unit.

7.2 WaterCop system not responding to sensor:

• Check the sensor's batteries.
• Ensure the sensor is within the 200 ft wireless range of the WaterCop control unit and there are no significant obstructions.
• Re-pair the sensor with the WaterCop control unit.
• Consult the WaterCop control unit's manual for troubleshooting its reception.

7.3 False alarms:

• Ensure the probe is not placed in an area where condensation or minor spills are common and not indicative of a leak.
• Check for any moisture on the probe that might be causing a false trigger.

8. Техникалык шарттар

9. Кепилдик жана колдоо

For warranty information and technical support, please refer to the official WaterCop webсайтка же түздөн-түз кардарларды тейлөөгө кайрылыңыз. Кепилдик дооматтар үчүн сатып алуу дүмүрчөгүңүздү сактаңыз.

Official WaterCop Webсайт: www.watercop.com

Contact Information: Refer to the webучурдагы байланыш маалыматтары үчүн сайт.