Introduction
This manual provides detailed instructions for the safe and effective use of the HI-Link HLK-PM01 AC-DC 220V to 5V Step-Down Power Supply Module. Please read this manual thoroughly before installation and operation.
1-сүрөт: Жогорку view of the HLK-PM01 AC-DC 220V to 5V Step-Down Power Supply Module, showing the HI-Link logo, input/output specifications, and model number.
Продукт өзгөчөлүктөрү
- Ultra-thin, subminiature design for compact integration.
- Толук томtage input range (90 ~ 264 Vac) for versatile applications.
- Low ripple and low noise output for stable power delivery.
- Integrated output overload and short circuit protection function for enhanced safety.
- High efficiency and power density.
- Designed to meet EMC and safety testing requirements.
- Low power consumption, green environmental protection, with no-load loss less than 0.1 W.
- 100% load test and aging test performed.
- Meets the requirements of UL and CE standards.
Коопсуздук чаралары
Always observe the following safety precautions to prevent injury or damage to the module:
- Киргизүү көлөмүн камсыз кылыңызtage is within the specified range (90-264 Vac).
- 0.6A максималдуу чыгаруу ток ашпагыла.
- Avoid direct contact with the module's pins when power is applied.
- Install the module in a well-ventilated area to prevent overheating.
- Ensure proper insulation and clearance from other components.
- This module is intended for integration into larger electronic systems by qualified personnel.
Жайгашуу
1. Pin конфигурациясы
The HLK-PM01 module has clearly labeled pins for input and output connections.
2-сүрөт: Бурчтуу view of the HLK-PM01 module, highlighting the input (AC) and output (+Vo, -Vo) pins.
- AC киргизүү: Two pins for AC line voltage (90-264V).
- +Vo Output: Positive 5V DC output.
- -Vo Output: Negative (Ground) 5V DC output.
2. Электр байланышы
- Identify the AC input terminals on the module. Connect your AC power source (90-264V) to these two terminals.
- Identify the +Vo and -Vo output terminals. Connect the positive input of your 5V DC load to +Vo and the negative/ground input to -Vo.
- Кыска туташуунун алдын алуу үчүн бардык туташуулардын коопсуз жана туура изоляцияланганын текшериңиз.
Эскертүү: For optimal performance and safety, consider adding appropriate input filtering and output capacitance as per your application's requirements, although the module has internal filtering.
Иштөө нускамалары
Once the module is correctly wired, operation is straightforward:
- Apply AC power to the input terminals. The module will immediately begin converting the AC voltagтуруктуу 5V DC чыгышына.
- Monitor the load to ensure it operates within the module's specified output current (max 0.6A).
- The module is designed for continuous operation within its specified parameters.
The module features built-in overload and short-circuit protection. In case of an overload or short circuit, the module will automatically protect itself and resume normal operation once the fault condition is removed.
Техникалык тейлөө
The HLK-PM01 module is designed for maintenance-free operation. However, periodic checks are recommended:
- Визуалдык текшерүү: Periodically inspect the module and its connections for any signs of physical damage, loose wires, or discoloration.
- Чаңды тазалоо: Ensure the module is free from excessive dust accumulation, which can impede heat dissipation. Use a soft brush or compressed air if necessary.
- Температура мониторинги: While operating, the surface temperature of the main converter should not exceed 90°C, and the shell surface maximum temperature should not exceed 60°C. Ensure adequate ventilation.
Do not attempt to open or repair the module. Refer to qualified personnel for any issues beyond basic inspection.
Проблемаларды чечүү
| Көйгөй | Мүмкүн себеп | Чечим |
|---|---|---|
| No 5V output | No AC input power; Incorrect wiring; Module failure. | Verify AC input power supply. Check all wiring connections for correctness and security. If wiring is correct and power is present, the module may be faulty and require replacement. |
| Чыгуу томtage unstable or low | Overload condition; Poor connections; Input voltagд термелүүлөр. | Reduce the load current to below 0.6A. Ensure all connections are firm. Verify the stability of the AC input voltage. |
| Module is hot | Excessive load; Insufficient ventilation. | Ensure the load current does not exceed 0.6A. Provide adequate airflow around the module. |
| Module shuts down intermittently | Overload protection triggered; Short circuit detected. | Check for intermittent short circuits or transient overloads on the output. The module should resume operation once the fault is cleared. |
Техникалык шарттар
| Параметр | Нарк |
|---|---|
| Модель номери | HLK-PM01 |
| Киргизүү көлөмүtage Диапазон | 90 - 264 Vac |
| Output Voltage | 5 Vdc |
| Output Current | 0.6 А (Max) |
| Номиналдуу кубаттуулук | 3 Вт |
| Жок жүк жоготуу | < 0.1 Вт |
| Өлчөмдөрү (L x W x Y) | Болжол менен 35 мм x 21 мм x 16 мм |
| Коргоо өзгөчөлүктөрү | Output Overload, Short Circuit Protection |
| Шайкештик | UL, CE requirements |
Эскертүү: Dimensions are approximate based on customer reviews. Refer to official HI-Link datasheets for precise measurements.
Кепилдик жана колдоо
For warranty information and technical support, please contact your point of purchase or visit the official HI-Link webсайт. Сатып алганыңыздын далили катары сатып алуу дүмүрчөгүңүздү сактаңыз.
Кошумча ресурстарды жана продукт маалыматын алуу үчүн, сиз иш сапары менен болот HI-Link Store on Amazon.
