Hunter X-Core XC601i-e 6-станциялуу үй ичиндеги сугаруу контроллери колдонуучунун колдонмосу

Introduction

This manual provides comprehensive instructions for the installation, operation, and maintenance of your Hunter X-Core XC601i-e 6-Station Indoor Irrigation Controller. Please read this manual thoroughly before installation and operation to ensure proper use and optimal performance of your irrigation system.

Продукт бүттүview

The Hunter X-Core XC601i-e is an indoor irrigation controller designed to manage up to 6 irrigation stations. It features three independent programs (A, B, C) with multiple start times, allowing for flexible scheduling of watering cycles. The intuitive dial and button interface simplify programming and manual operation.

1-сүрөт: Front panel of the Hunter X-Core XC601i-e controller. It displays a digital screen at the top, control buttons (+, -, arrow keys, PRG) above the main dial, and a large central dial with various settings: System Off, Manual, Solar Sync, Seasonal Adjust, Date/Time, Start Times, Run Times, and Water Days. The Hunter logo is visible at the bottom.

Жайгашуу

1. Контроллерди орнотуу

1. Күндүн тике тийген нурларынан жана экстремалдык температурадан корголгон стандарттуу электр розеткасынын жанында ылайыктуу имаратты тандаңыз.
2. Use the provided mounting template or mark the two mounting holes on the wall.
3. Install two screws into the wall, leaving approximately 3mm of the screw head exposed.
4. Hang the controller on the screws using the keyhole slots on the back.

2. Контроллерди туташтыруу

Коопсуздук чарасы: Ensure the power supply is disconnected before performing any wiring.

• Кубат туташуу: Connect the two wires from the external transformer to the two terminals labeled "24 VAC" on the controller's terminal strip.
• Клапан зымдары:
  1. Connect one wire from each solenoid valve to a separate station terminal (1-6).
  2. Connect the common wire from all solenoid valves to the terminal labeled "COM".
• Негизги клапанды/насосту ишке киргизүү (милдеттүү эмес): If using a master valve or pump start relay, connect one wire to the terminal labeled "MV" and the other to the "COM" terminal.
• Сенсордук зымдар (милдеттүү эмес): If using a rain sensor or other weather sensor, connect the sensor wires to the two terminals labeled "SEN". Ensure the sensor bypass switch is set correctly.

3. Initial Power-Up and Basic Settings

1. Connect the transformer to a power outlet. The display should illuminate.
2. Дата/убакыт коюу:
   • терүү үчүн бургула Дата/Убакыт позиция.
   • колдонуу + or - buttons to adjust the year, month, day, and time.
   • колдонуу > button to move between settings.

Иштөө нускамалары

The X-Core controller uses a central dial for navigation and dedicated buttons for adjustments.

Башкаруу терүү позициялары:

• Система өчүк: Turns off all automatic and manual watering.
• Кол менен: Allows for manual operation of individual stations or programs.
• Дата/Убакыт: Used to set the current date and time.
• Баштоо убактысы: Used to set the start times for programs A, B, and C.
• Иштөө убактысы: Used to set the watering duration for each station within programs A, B, and C.
• Суу күндөрү: Used to select specific watering days or intervals for programs A, B, and C.
• Сезондук тууралоо: Adjusts all program run times by a percentage (e.g., 100% for normal, 50% for half).
• Solar Sync: (If equipped and enabled) Automatically adjusts watering based on local weather conditions.

Programming Automatic Watering:

The X-Core has three independent programs: A, B, and C. Each program can have up to four start times.

1. Программаны тандоо: басыңыз PRG button to cycle through programs A, B, and C.
2. Баштоо убакыттарын коюу:
   • Тергичти буруңуз Times Times.
   • Колдонуу + or - to set the desired start time.
   • Басыңыз PRG or > to move to the next start time (up to four per program).
3. Иштөө убакыттарын коюу:
   • Тергичти буруңуз Run Times.
   • The display will show the program and station number. Use + or - to set the watering duration (in minutes) for each station.
   • Колдонуу > to advance to the next station.
4. Суу күндөрүн белгилөө:
   • Тергичти буруңуз Суу күндөрү.
   • Select watering days (e.g., Monday, Wednesday, Friday) or an interval (e.g., every 2 days) using the + or - баскычтар.
   • The > button can be used to cycle through day options.
5. Return to RUN: After programming, turn the dial to the RUN position for automatic operation.

Кол менен иштөө:

1. Тергичти буруңуз Manual.
2. колдонуу > button to select the desired station or program.
3. Колдонуу + or - to set the manual run time.
4. The selected station or program will begin watering immediately.
5. To stop manual watering, turn the dial to Тутум өчүк or RUN.

Техникалык тейлөө

Батареяны алмаштыруу:

The X-Core controller uses one AAA battery to maintain the time and program settings during power outages. It is recommended to replace the battery annually.

1. Locate the battery compartment on the back or side of the controller.
2. Open the compartment and remove the old AAA battery.
3. Туура полярдуулукту камсыз кылуу үчүн жаңы AAA батарейкасын салыңыз.
4. Батарея отсегин жабыңыз.

Note: The controller requires AC power for valve operation. The battery only preserves settings.

Жалпы кам көрүү:

• Контроллерди таза жана чаңдан алыс кармаңыз. Тазалоо үчүн жумшак, кургак чүпүрөктү колдонуңуз.
• Ensure the controller is not exposed to moisture or extreme temperatures, as it is designed for indoor use.

Проблемаларды чечүү

Техникалык шарттар

• Модел: XC601i-e
• Станциялар: 6
• Программалар: 3 independent programs (A, B, C)
• Баштоо убактысы: Up to 4 per program
• Кубат киргизүү: 230 VAC, 50/60 Hz (via external transformer)
• Чыгуу кубаттуулугу: 24 VAC, 1.0 А
• Батарея: 1 x AAA (for time and program backup)
• Өлчөмдөрү (болжол менен): 25.5 x 18.5 x 8 cm (Package dimensions, actual unit may vary slightly)
• Салмагы (болжол менен): 3 kg (Package weight, actual unit may vary slightly)
• Ичинде гана колдонуу