1. Киришүү
This manual provides essential information for the safe and efficient operation of the SMT Ultrasonic Homogenizer UH-50. Please read this manual thoroughly before using the device and keep it for future reference.
The SMT Ultrasonic Homogenizer UH-50 is a compact and lightweight device designed for laboratory applications requiring ultrasonic homogenization. Its key features include a space-saving design, a lightweight vibrator (approximately 160g), and a hand pulser for convenient control of ultrasonic vibration. The system automatically adjusts output to maintain a constant amplitude, adapting to variations in sample load and pressure.
2. Коопсуздук маалыматы
WARNING: This is a professional-use product. It should only be operated by trained personnel in a laboratory setting.
- No Dry Operation: Do not operate the ultrasonic vibrator without it being immersed in a liquid sample. Dry operation can cause damage to the device.
- Түзмөктүн туруктуу, тегиз бетке коюлганын текшериңиз.
- Connect the device to a grounded power outlet with the specified voltage (AC100V, 50/60Hz).
- Avoid direct contact with the vibrating tip during operation.
- Түзмөктү өз алдынча бөлүп же оңдоого аракет кылбаңыз. Квалификациялуу тейлөө кызматкерлерине кайрылыңыз.
- Keep the unit away from flammable materials and excessive moisture.
3. Продукциянын компоненттери жана башкаруу элементтери
The SMT Ultrasonic Homogenizer UH-50 consists of a main control unit and an ultrasonic vibrator with a hand pulser. Familiarize yourself with the components and controls shown below.
Figure 1: SMT Ultrasonic Homogenizer UH-50 Overview
This image displays the main control unit of the SMT Ultrasonic Homogenizer UH-50 on the left, connected to the ultrasonic vibrator on the right. The control unit features a "MONITOR" display, a "POWER" switch, "CONSTANT" and "HAND" mode selector, "TUNE" and "OUTPUT" adjustment knobs. A yellow label on top of the main unit warns against dry operation. The vibrator is a slender, metallic component with a tip.
Control Panel Description:
- POWER которуштуруу: Агрегатты күйгүзөт жана өчүрөт.
- MONITOR Display: Shows the current output level or other operational parameters.
- CONSTANT/HAND Selector:
- ТУРУКТУУ: Continuous ultrasonic operation.
- КОЛ: Operation controlled by the hand pulser switch.
- TUNE Knob: Adjusts the ultrasonic frequency for optimal performance.
- OUTPUT баскычы: Controls the ultrasonic power output (ampлитуда).
- Hand Pulser: A switch located on the vibrator cable for convenient start/stop of ultrasonic vibration when in HAND mode.
4. Орнотуу
- Пакеттен чыгаруу: Таңгактан бардык компоненттерди этияттык менен алып салыңыз. Бардык тетиктердин таңгактоо тизмесине ылайык бар экенин текшериңиз.
- Жайгашкан жери: Place the main control unit on a stable, flat, and dry surface, ensuring adequate ventilation around the unit.
- Вибраторду туташтырыңыз: Connect the ultrasonic vibrator cable securely to the designated port on the main control unit.
- Кубат туташуу: Ensure the POWER switch is in the "OFF" position. Connect the power cord to the main control unit and then to a grounded AC100V, 50/60Hz power outlet.
- Алгачкы текшерүү: Before first use, visually inspect the vibrator tip for any damage or wear.
5. Иштөө нускамалары
Always ensure the vibrator tip is immersed in the sample liquid before starting operation to prevent damage from dry running.
- Даярдоо Сampле: Силерди койгулаample in an appropriate vessel. Ensure the vessel is suitable for ultrasonic treatment and can withstand the energy generated.
- Immerse Vibrator: Carefully immerse the tip of the ultrasonic vibrator into the sample liquid. Ensure the tip is sufficiently submerged but not touching the bottom or sides of the vessel.
- Күйгүзүү: Turn the POWER switch to the "ON" position. The MONITOR display should illuminate.
- Режимди тандоо:
- For continuous operation, set the selector to "CONSTANT".
- For intermittent operation controlled by the hand pulser, set the selector to "HAND".
- Adjust TUNE: Slowly adjust the TUNE knob until the MONITOR display shows the highest stable reading, indicating optimal resonance.
- Set OUTPUT: Adjust the OUTPUT knob to the desired ultrasonic power level. The system will automatically control the output to maintain a constant ampжарыктык.
- Start Homogenization:
- In "CONSTANT" mode, homogenization will start immediately.
- In "HAND" mode, press and hold the switch on the hand pulser to start homogenization. Release the switch to stop.
- Монитор процесси: Observe the homogenization process. Adjust OUTPUT or TUNE as necessary.
- Аяктоо: Once homogenization is complete, turn the OUTPUT knob to minimum, then turn the POWER switch to "OFF".
- Clean Vibrator: Carefully remove the vibrator from the sample and clean it immediately according to the maintenance instructions.
6. Техникалык тейлөө
Regular maintenance ensures the longevity and optimal performance of your SMT Ultrasonic Homogenizer UH-50.
- Cleaning the Vibrator Tip: After each use, thoroughly clean the vibrator tip to prevent sample residue buildup. Use appropriate cleaning agents for the materials being processed. Rinse with distilled water and dry completely.
- Негизги блокту тазалоо: Wipe the exterior of the main control unit with a soft, damp cloth. Do not use abrasive cleaners or allow liquids to enter the unit.
- Текшерүү: Periodically inspect the vibrator tip, cable, and connectors for any signs of wear, damage, or corrosion. Replace damaged parts immediately.
- Сактагыч: Колдонулбай турган учурда, түзмөктү таза, кургак чөйрөдө сактаңыз.
7. Кыйынчылыктарды
If you encounter issues with your SMT Ultrasonic Homogenizer UH-50, refer to the following common problems and solutions:
- Кубат жок:
- Кубат шнуру түзмөккө да, розеткага да бекем туташтырылганын текшериңиз.
- Электр розеткасынын иштешин текшериңиз.
- Verify the POWER switch is in the "ON" position.
- No Ultrasonic Vibration:
- Ensure the vibrator tip is properly immersed in liquid.
- Check the TUNE and OUTPUT knob settings. Adjust TUNE for optimal resonance.
- If in "HAND" mode, ensure the hand pulser switch is pressed.
- Inspect the vibrator cable for damage.
- Төмөн же дал келбеген чыгаруу:
- Adjust the TUNE knob to find the optimal frequency.
- Increase the OUTPUT knob setting.
- Ensure the vibrator tip is clean and free of damage.
- s текшериңизample volume and viscosity are within appropriate limits for the device.
If the problem persists after attempting these solutions, please contact SMT customer support or your local distributor for assistance.
8. Техникалык шарттар
| Өзгөчөлүк | Спецификация |
|---|---|
| Модель номери | UH-50 |
| Өлчөм (Негизги бирдик) | 182 × 320 × 110 мм |
| Электр камсыздоо | AC100V, 50/60Hz, 2A |
| Чыгуу күчү | 50 Вт |
| Максималдуу Ampжарыктык | 40 мкм |
| Жыштык | 20 кГц |
| Vibrator Outer Dimensions | φ32 × 297 мм |
| Included Tip | 3mm (Titanium Alloy) |
| Vibrator Weight | Болжол менен 160г |
| Продукт Салмагы | 3.16 кг |
| Батареяны колдонуу | Жок |
9. Кепилдик жана колдоо
Specific warranty information for the SMT Ultrasonic Homogenizer UH-50 is not provided in this document. Please refer to your purchase agreement or contact your local SMT distributor for details regarding warranty coverage and technical support.
Кошумча жардам алуу үчүн, сиз да барсаңыз болот SMT Brand Store on Amazon.co.jp.
