KICKER CVR10 CompVR 10-Inch (250mm) Subwoofer Instruction Manual

1. Киришүү

This manual provides essential information for the proper installation, operation, and maintenance of your KICKER CVR10 CompVR 10-Inch (250mm) Subwoofer. Please read this manual thoroughly before use to ensure optimal performance and longevity of your product.

Сүрөт 1.1: Алдыңкы view of two KICKER CVR10 CompVR 10-inch subwoofers. These subwoofers feature a black cone with a red stitching accent around the perimeter and a central KICKER logo.

2. Коопсуздук маалыматы

Ар дайым төмөнкү коопсуздук чараларын сактаңыз:

• Disconnect the vehicle's battery before installing any audio components to prevent electrical shorts.
• Ensure all wiring is properly insulated and secured to prevent damage and short circuits.
• Do not operate the subwoofer beyond its rated power handling capabilities to avoid damage.
• High sound pressure levels can cause permanent hearing loss. Use caution when adjusting volume levels.
• Consult a professional installer if you are unsure about any installation procedures.

3. Пакеттин мазмуну

Пакетиңизде бардык буюмдар бар экенин текшериңиз:

• KICKER CVR10 CompVR 10-Inch (250mm) Subwoofer (Quantity: 1 or 2, depending on bundle)
• Mounting Screws (16 pieces, 1-5/8" wood screws)
• Көрсөтмө (бул документ)

4. Орнотуу жана орнотуу

4.1 Mounting the Subwoofer

The KICKER CVR10 CompVR subwoofer is designed for installation in a custom enclosure. Ensure the enclosure meets the recommended volume specifications for optimal performance.

• Монтаждоо диаметри: 9-3/16 дюйм (23.3 см)
• Монтаждоо тереңдиги: 5-1/2 дюйм (14 см)

Use the provided 1-5/8" wood mounting screws to secure the subwoofer to the enclosure. Ensure a tight, airtight seal between the subwoofer frame and the enclosure.

Сүрөт 4.1: Каптал view of the KICKER CVR10 CompVR subwoofer, illustrating its mounting depth and overall profile. Бул view highlights the robust surround and basket design.

4.2 Wiring Instructions (2-Ohm DVC)

The CVR10 CompVR features a 2-Ohm Dual Voice Coil (DVC) design. This allows for flexible wiring configurations to match various amplifier impedances. Always ensure your amplifier is stable at the final impedance load.

Single Subwoofer Wiring:

• 1-Ohm Load (Parallel Wiring): Connect the positive terminals of both voice coils together, and the negative terminals of both voice coils together. Connect the amplifier's positive output to the combined positive terminals, and the amplifier's negative output to the combined negative terminals. This results in a 1-Ohm load.
• 4-Ohm Load (Series Wiring): Connect the positive terminal of one voice coil to the negative terminal of the other voice coil. Connect the amplifier's positive output to the remaining positive terminal, and the amplifier's negative output to the remaining negative terminal. This results in a 4-Ohm load.

Two Subwoofer Wiring (for a bundle):

When using two CVR10 CompVR subwoofers, various configurations are possible depending on the desired final impedance. Common configurations include:

• 0.5-Ohm Load: Wire each subwoofer for a 1-Ohm load (parallel), then wire the two 1-Ohm subwoofers in parallel. (Caution: Very few amplifiers are stable at 0.5 Ohms.)
• 2-Ohm Load: Wire each subwoofer for a 4-Ohm load (series), then wire the two 4-Ohm subwoofers in parallel. Alternatively, wire each subwoofer for a 1-Ohm load (parallel), then wire the two 1-Ohm subwoofers in series.
• 8-Ohm Load: Wire each subwoofer for a 4-Ohm load (series), then wire the two 4-Ohm subwoofers in series.

Always refer to your amplifier's manual for its minimum stable impedance and recommended wiring configurations.

5. Иштөө нускамалары

5.1 Электр менен иштөө

The KICKER CVR10 CompVR subwoofer has a recommended RMS power handling of 400 Watts and a peak power handling of 800 Watts. It is crucial to match your amplifier's output to these specifications to prevent damage and ensure optimal sound quality.

5.2 Enclosure Recommendations

The performance of your subwoofer is highly dependent on the enclosure it is installed in. The CVR10 CompVR works best in either sealed or ported (vented) enclosures. Refer to the specifications section for recommended enclosure volumes.

• Жабылган Корпу: Provides tight, accurate bass response.
• Vented (Ported) Enclosure: Offers louder, more extended bass output at lower frequencies.

Consult KICKER's official resources or a professional installer for detailed enclosure design and tuning specific to your vehicle and listening preferences.

6. Техникалык тейлөө

The KICKER CVR10 CompVR subwoofer requires minimal maintenance to ensure long-term performance.

• Тазалоо: Use a soft, dry cloth to gently wipe down the cone and surround. Avoid using harsh chemicals or abrasive cleaners.
• Текшерүү: Periodically check all wiring connections to ensure they are secure and free from corrosion. Inspect the subwoofer's surround for any signs of cracking or damage.
• Курчап турган чөйрө: Ensure the subwoofer is installed in an environment free from excessive moisture, direct sunlight, and extreme temperatures.

7. Кыйынчылыктарды

Сабвуфериңизде көйгөйлөр пайда болсо, төмөнкү жалпы көйгөйлөрдү жана чечимдерди караңыз:

8. Техникалык шарттар

Detailed technical specifications for the KICKER CVR10 CompVR 10-Inch Subwoofer:

9. Кепилдик жана колдоо

9.1 Кепилдик маалыматы

KICKER products are covered by a limited warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official KICKER webсайт. Сатып алуу квитанциясын кепилдик дооматтары үчүн сатып алуунун далили катары сактаңыз.

9.2 Кардарларды колдоо

For technical assistance, troubleshooting, or further inquiries, please contact KICKER customer support. You can find contact information and additional resources on the official KICKER webсайт:

Visit the KICKER Store on Amazon